Magnadyne M1-NAV Technisches Datenblatt

Operation

and Installation

Manual

GPS

NAVIGATION BOX

M1-NAV

Navigation Module

M1-NAV 8/4/08 1:27 PM Page 1

Please read this section carefully and follow all the instructions given. This will help ensure reliable opera-

tion and extend the service life of the unit.

Caution

1. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your

passengers and pedestrians, and abiding all state and local traffic regulations. Do not use any fea-

tures of this system to the extent it distracts you from safe driving. Your first priority while driving

should always be the safe operation of your vehicle. Magnadyne will not accept any responsibility

whatsoever for accidents and/or injuries resulting from failure to observe these precautions or safety

instructions.

2. Only look at the display when you are in a safe driving situation!

3. The road layout and driving rules take precedence over the instructions of the instructions of the nav-

igation system. Only follow the instructions when circumstances and driving rules permit it!

4. The direction statements of the navigation system given do not release the driver of the vehicle from

his or her duty of care or personal responsibility.

5. Plan routes before your leave. If you want to plan a new route, pull over and stop driving.

WARNING!

Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be

repaired, consult your dealer.

Operating Environment

1. Mount in a safe location to avoid high temperatures (e.g. heater duct.). Do not install the unit in a

spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust

or the possibility of water splashing.

2. Protect the unit from getting wet. If the unit gets wet, unplug the unit and bring it to an authorized

service department.

3. Avoid heavy vibrations and shaking.

4. Failure to follow these instructions may lead to damage to the unit.

Electromagnetic Compatibility

Please note that only the supplied shielded cable should be used with this unit. For optimal perfor-

mance, maintain a distance of a least 10ft. from sources of high-frequency and magnetic interference

(televisions, loudspeaker systems, mobile telephone and so on). This will help avoid malfunctions and

loss of data.

Safety Instructions

• THIS DEVICE IS INTENDED FOR CONTINUOUS

OPERATION.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK AND ANNOYING INTERFERENCE, USE

ONLY THE RECOMMENDED ACCESSORIES.

Caution

• FCC REGULATIONS STATE THAT ANY UNAUTHO-

RIZED CHANGES OR MODIFICATIONS TO THIS

EQUIPMENT MAY VOID THE USER’S AUTHORITY

TO OPERATE IT.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO

RAIN OR MOISTURE.

M1-NAV 8/4/08 1:27 PM Page 2

Index

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Caution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Voice Control Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Selecting the Navigation Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Selecting a Different Source from Navigation Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Calibrating the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Loading a Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

Main Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Map Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Point on the Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Destinations Menu

Address Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

Recent Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

My Favorites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-18

POI (Points of Interest). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-21

Cancel Route. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Route Manager Menu

Turn by Turn List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23

Route Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Avoid Roads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-26

Route Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27

Quick Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Map Manager Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29

Extra Menu Tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Multistop Planner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-32

Navigation Setting Menu

Prompts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Feature Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

M1-NAV 8/4/08 1:27 PM Page 3

Navigation Voice Control: You can specify if you want the navigation’s voice to interrupt the audio of another

source and give turn directions. For example, with a navigation destination selected and the Navigation Voice

is On and you switch the source to the radio, the radio will be interrupted to give navigation turn directions.

Note: In the navigation source screen the navigation voice is always on and can not be turned off.

Voice Control Set-up

Selecting the Navigation Source

Selecting the Navigation Source:

Press the HOME button to select the source

screen. Then press the NAVIGATION button to

select the navigation source.

Selecting the Destinations Menu:

Press the Navigation button to select the

“Destinations” menu.

Read the Warning statement and if you acknowl-

edge your responsibility press the Agree button.

The Destinations menu with the primary naviga-

tion features will be displayed. See “Getting

Started” page 7 for more information.

To access the Navigation Voice button press the

SETTINGS button in the Home Row then press

the SOUND button.

Turn the navigation voice on or off by touching

the NAVIGATION VOICE OFF/ON button.

M1-NAV 8/4/08 1:34 PM Page 4

Selecting a Different Source from Navigation Screen

Selecting a Different Source:

Press the button to leave the navigation

source and return to the last selected source.

Calibrating the Screen

When you first connect the GPS box to the stereo receiver you should adjust the screen to the center

position and calibrate the touch screen.

1. When the navigation system starts up and the

Console menu is displayed, press the Setting

button.

2. Press the Screen Adjust button to enter the

Centering the Screen Adjustment mode.

3. Use the , , and buttons to move the

screen up/down and left/right to center the

screen. When the screen is centered press the

OK button to confirm the screen adjustment.

4. Press the Touch Cali button to enter the

screen’s Touch Calibration Adjustment mode.

M1-NAV 8/4/08 1:34 PM Page 5

Loading a Map

Before you can use the navigation system you must load the appropriate map. For example, if you are

going to be using the navigation system in California you must load the PACIFIC map which includes CA,

OR and WA. Follow the procedure below to load the appropriate map:

1. From the Destinations menu press the Next

button.

2. From the Options menu press the Map

Manager button.

3. From the Map Manager menu press the

Select Map button.

Calibrating the Screen

5. You will see a +displayed on the screen.

Touch the +firmly, the +will continue to

move until the screen is aligned. Continue

to touch the +firmly until OK appears on

the screen. Press OK to exit the screen’s

Touch Calibration Adjustment mode.

6. Press the Xto exit the screen’s calibration

screen.

Note: The Navi Opt, GPS Monitor,

Language Opt and System Info buttons

have no user adjustable settings.

M1-NAV 8/4/08 1:35 PM Page 6

Getting Started

Destinations Menu:

123

6 7 8

4 5

1. Address:

The Address button lets you navigate to an

address by inputting an address. (See Address

Button on page 11).

2. Recent Location:

The Recent Locations button lets you navigate

to a previously visited destination. (See Recent

Locations on page 13).

3. My Favorites:

The My Favorites button lets you navigate to a

favorite location. (See My Favorites on page 15).

4. POI (Points of Interest):

The POI button lets you navigate to thousands

of interesting places. (See POI “Points of

Interest” on page 19).

5. Cancel Route:

The Cancel Route button stops the current

route navigation.

6. Quit:

The Quit button quits the navigation system.

7. Map:

The Map button activates the Main Map screen.

8. More:

The More button activates the Option menu.

4. Locate the map containing your state by using

the  or  buttons. Press the Select button

to load the map.

Your Location

5. The navigation unit will then automatically

display the Main Map screen and show your

location on the map.

Note: If the map is blank you have selected

the incorrect map. Follow the procedures

again to load the correct map.

Loading a Map (Continued)

M1-NAV 8/4/08 1:35 PM Page 7

Settings Menu:

Getting Started (Continued)

1 2 3

6 7 8

4 5

1. Day/Night Mode:

The Day/Night button adjusts the display for

either day or night driving. (See Maps Views on

page 10).

2. 2D/3D View Mode:

The 2D/3D button displays the map view in

either a 2-dimensional or 3-dimensional view.

(See Map Views on page 10).

3. Route Manager:

Pressing the Route Manager button selects a sec-

ondary menu. (See Route Manager on page 22).

4. Map Manager:

Pressing the Map Manager button selects a sec-

ondary menu. (See Map Manager on page 28).

5. Extras:

The Extra button button

selects a secondary

menu that contains a tutorial button which will

familiarize your with the navigation features. Also

included is a Multi-Stop Planner button (See

Multi-stop Planner on page 30).

6. Back:

The Back button returns you to the Destinations

menu.

7. Map:

The Map button activates the Main Map screen.

8. Settings:

The Settings button activates the Settings

menu.

Options Menu:

From the Destinations menu

press the Next button.

1 2 3

6 7 8

4 5

From the Option menu

press the Settings button.

1. Prompts:

Lets you specify the type of voice or visual

prompts. (See Prompts on page 32).

2. Language:

Lets you select the language text and voice

guidance language.

3. Time:

Use to select the time zone.

4. GPS Signal:

Provides information on location of available

GPS satellites.

5. Help:

Not applicable

6. Back:

The Back button returns you to the Options

menu.

7. Map:

The Map button activates the Main Map screen.

8. About:

Displays software version and copyright infor-

mation.

M1-NAV 8/4/08 1:35 PM Page 8

Main Map

Current Location:

Current Location

Zooms Display

Out

Compass

Quick Nav GPS Status

No Function GPS Generated

Information Area

Destinations

Zooms Display

Direction Bar

Indicates current location.

Indicates last know location before GPS

signal was lost.

Generated Route:

Press the GPS Generate information Area to

display the following information:

Remaining Travel Time and Distance _

Estimated Time of Arrival _

> Current Street _

Speed and Altitude _

> Remaining Travel Time

and Distance.

Compass:

Indicates direction of travel.

GPS Status:

Green GPS receiver means reliable signal.

Red GPS receiver means unreliable signal.

GPS Generated Information Area:

When you have calculated a route, press the

Direction Bar to display the Turn-by-Turn

screen for a complete list of directions.

Direction Bar:

Note: When you first start the navigation system

you will hear the message “Signal too low”. This

message means that your navigation device hasn’t

yet located a reliable GPS signal. Depending on

your location it may take a few seconds to acquire

a reliable GPS signal. For example, if your car is

parked in the garage the navigation system may

not be able to acquire a reliable GPS signal. Move

your vehicle until you have a clear view of the sky.

Displays generated route by the

navigation system.

Quick Nav:

See Route Manager section for more infor-

mation on page 28.

M1-NAV 8/4/08 1:40 PM Page 9

Map Views

2D Views:

Day Map View

Night Map View

3D Views:

Day Map View

Point on the Map

You can navigate to any point by touching its location directly on the Main Map screen in both 2D and 3D

map views. This feature is especially helpful when you want to navigate to a specific point on the map, but

you don’t have the street address.

1. Press the map at a specific point on the map.

2. The context menu appear with the following

options:

Go There: This button lets you calculate a

route from the map point.

Add to My Favorites: This button lets you

save a point on the map as a favorite des-

tination.

Night Map View

M1-NAV 8/4/08 1:40 PM Page 10

Inhaltsverzeichnis

Andere Magnadyne GPS Handbücher

Magnadyne

Magnadyne CoPilot Gebrauchsanweisung

Beliebte GPS Handbücher anderer Marken

Raven

Raven Cruizer II Handbuch

Hama

Hama 53118 Bedienungsanleitung

Garmin

Garmin SOUNDER 125 Bedienungsanleitung

Garmin

Garmin DEZL 580 Bedienungsanleitung

Jigabot

Jigabot EX Bedienungsanleitung

Pointer

Pointer Cellocator CelloTrack XT LTE Installationsanleitung

Queclink

Queclink GV55LITE Bedienungsanleitung

Voxson

Voxson Voxtrack GPS500 Gebrauchsanweisung

Garmin

Garmin ECHOMAP PLUS Bedienungsanleitung

Starcom Systems

Starcom Systems Kylos Compact Bedienungsanleitung

Garmin

Garmin 15 H Series Bedienungsanleitung

Cobra

Cobra Marine MC 600Ci Bedienungsanleitung

Cellocator

Cellocator CelloTrack T Bedienungsanleitung

Enfora

Enfora Mini-MT GSM2228UG001 Bedienungsanleitung

Magellan

Magellan eXplorist 100 Bedienungsanleitung

LTE

LTE G50B Bedienungsanleitung

Garmin

Garmin DEZL OTR500 Bedienungsanleitung

SkyGolf

SkyGolf SkyCaddie SG1 Bedienungsanleitung