Mainstays MS17-D4-1011-03 Bedienungsanleitung

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Date 2017-05-04 Rev. 0001-A Factory: FOCIDI

3-in-1TM TV Stand

Model # MS17-D4-1011-03

U.S. Patent 8,561,551

CA Patent 2,811,974

This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your

needs. DO NOT discard any of the hardware or parts that you will not use on your chosen option.

This will allow you to use this TV console in different configurations at a later date, if desired.

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to

the store where it was purchased. Please call our customer service number and have your

instructions and parts list ready to provide the model name, part name or factory number:

866-942-5362

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday

Or visit our web site 24 hours a day, 7 days a week for product assistance at

www.whalenstyle.com

Or e-mail your request to parts@whalenfurniture.com

LOT NUMBER:

DATE PURCHASED: / /

MANUFACTURER: Whalen Furniture Manufacturing

CATALOG: 3-in-1

TV Stand

MODEL # MS17-D4-1011-03

MADE IN CHINA

1. Please read the Assembly Instructions prior to assembling this product.

2. Remove all hardware from the box and sort by size.

3. Check to see that all hardware and parts are present BEFORE assembling.

4. Ask a friend to assist you with the assembly of this furniture.

5. To avoid damage, assemble the product on a sturdy, level and protective surface.

6. Please wait until all steps are completed before fully tightening Bolts.

7. Make sure all Bolts are tightly fastened before the unit is used.

MAXIMUM RECOMMENDED WEIGHT LOADS

FITS UP TO MOST 177.8 cm / 70 in FLAT PANEL TVs

MAXIMUM LOAD 61.2 kg / 135 lb

FITS UP TO MOST 177.8 cm / 70 in FLAT PANEL

TVs WITHOUT SWIVELING BRACKET

MAXIMUM LOAD 61.2 kg / 135 lb

MAXIMUM LOAD 22.6 kg / 50 lb

GENERAL INFORMATION, TIPS

and

TRICKS

This product is sold with one set of Tipping Restraint Hardware Kit. You must install the

Tipping Restraint Hardware between the wall and the TV stand to prevent any accidents or

damages. When properly installed, this restraint can provide protection against the

unexpected tipping of the unit due to small tremors, bumps or climbing. The restraint is only a

deterrent and is not a substitute for proper adult supervision. Use of tip-over restraints may

only reduce, but not eliminate, the risk of tip-over.

THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH

FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND

WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL

TVS OREQUIPMENT. TOAVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTRE OF THE

UNIT; THE BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING

SURFACE OF THE UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY

POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT

EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT,

CAUSING POSSIBLE SERIOUS INJURY.

PLACE TV BEHIND THE STOPPER

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts and hardware

are present before beginning assembly.

A- Top Panel with Metal Frame B- Middle Metal Frame C- Bottom Panel with Metal Frame

(Qty. 1) (Qty. 1) (Qty. 1)

D- Spine Assembly (Qty. 1) E- Leg (Qty. 2) F- Top Frame Support (Qty. 1)

G- Middle Glass Shelf (1) H- Swiveling Bracket (Qty. 1) I- Mounting Frame (Qty. 1)

J- Monitor Bracket (Qty. 2) K- Cable Wheel (Qty. 2) L- Stop Rail (Qty. 1)

(1) 1/2” Bolt (2) 5/8” Bolt (3) 1” Bolt (4) 1-5/8” Bolt

(Qty. 4+1 extra) (Qty. 15+1 extra) (Qty. 6+1 extra) (Qty. 10+1 extra)

(5) 2-1/2” Bolt (6) Lock Washer (7) Flat Washer (8) Flange Nut

(Qty. 1+1 extra) (Qty. 16+1 extra) (Qty.16+1 extra) (Qty. 1+1 extra)

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts and hardware

are present before beginning assembly.

(9) 2-1/2” Lag Bolt (10) Large Flat Washer (11) Concrete Anchor (12) Plastic End Cap

(Qty. 4) (Qty. 4+1 extra) (Qty. 4) (Qty. 1)

(13)

Glass Bumper (Qty. 8+1 extra)

4 mm Hex Wrench (Qty. 2)

3/16” Hex Wrench Touch-up Pen Tipping Restraint Hardware Kit (Qty. 1)

(Qty. 1) (Qty. 1) (Inside Plastic Bag)

TV Mounting Kit

M4 x 12 Bolt (Qty. 4) M4 x 30 Bolt (Qty. 4) M5 x 12 Bolt (Qty. 4) M5 x 30 Bolt (Qty. 4)

M6 x 12 Bolt (Qty. 4) M6 x 35 Bolt (Qty. 4) M8 x 16 Bolt (Qty. 4) M8 x 40 Bolt (Qty. 4)

M4 Lock Washer

(Qty. 4)

M5 Lock Washer

(Qty. 4)

M6 Lock Washer

(Qty. 4)

M8 Lock Washer

(Qty. 4)

Large Spacer (Qty. 4) Small Spacer (Qty. 4) M4/M5 Flat Washer (Qty. 8) M6/M8 Flat Washer (Qty. 4)

Tools required: Hex wrench (provided) and Phillips screwdriver (not provided).

Assembly Instructions

NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,

go back and fully tighten all bolts. This will make the assembly easier.

1. Unpack the unit and confirm that you have all the hardware and required parts.

2. Locate the Spine Assembly (D) and set the back face down on a scratch-free surface.

3. Fasten the Top Panel (A) to the Spine (D) with two 5/8” Bolts (2) and two Washers (6 and 7).

Lock Washer

(2 used in this step)

⑥

Flat Washer

(2 used in this step)

⑦

5/8” Bolt

(2 used in this step)

②

Assembly Instructions

4. Fasten the Middle Shelf Frame (B) to the Spine (D) with two 1-5/8” Bolts (4).

1-5/8” Bolt

(2 used in this step)

④

Assembly Instructions

5. Fasten the Bottom Shelf Frame (C) to the Spine Assembly (D) with two 1” Bolts (3).

1” Bolt

(2 used in this step)

③

Assembly Instructions

6. Align and attach one Leg (E) to the Shelf Frames (A and B) with four 1-5/8” Bolts (4).

7. Fasten the Leg (E) to the Bottom Shelf Frame (C) with two 1” Bolts (3).

8. Repeat the same procedure to attach the other Leg (E) at the opposite side.

A/B

1” Bolt

(4 used in this step)

③

1-5/8” Bolt

(8 used in this step)

④

Assembly Instructions

9. Fasten the Top Frame Support (F) to the middle rail of the Top Shelf Frame (A) and the Spine

(D) with three 5/8” Bolts (2) and three Washers (6 and 7).

10.Stand the unit upright.

Lock Washer

(3 used in this step)

⑥

Flat Washer

(3 used in this step)

⑦

5/8” Bolt

(3 used in this step)

②

If you choose

the

Table

top configurat

ion

continue to the next step.

If mounting the TV to the Floating Swivel

Mount, skip ahead to PAGE 16.

Assembly Instructions for Table-top Display

11.Remove the Upper Spine from the assembled unit by unscrewing the four bolts and four

washers with the provided hex wrench as shown.

NOTE: The upper spine is pre-installed for shipping. Keep the bolts and the washers for the

future used.

Inhaltsverzeichnis

Sprachen:

Andere Mainstays Rack & Stand Handbücher

Mainstays

Mainstays CONRAD MS18-D1-1007-55 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung