MakerBot Replicator 2X Bedienungsanleitung
Replacing the Extruders on a MakerBot Replicator 2X
These are instructions for removing the extruders on the MakerBot Replicator
2X Experimental 3D Printer and replacing them with new ones. To complete this
part replacement, you will need the 2.5 mm hex wrench that came with your
MakerBot Replicator 2X, some masking tape, a marker and possibly a small
flathead screwdriver.
Before you start working on your MakerBot Replicator 2X:
• Unload any filament.
• Turn off the MakerBot Replicator 2X
• Remove the filament guide tubes from the extruders
• Unplug power and USB cables
1. Remove the enclosure lid from the Replicator 2X
2. Remove the left fan assembly
Open the enclosure door to gain access to the inside of your MakerBot
Replicator 2X. Use the 2.5 mm hex wrench that came with your 3D printer to
remove the bolts at the lower edge of the left extruder fan. Pull the bolts, fan
guard, fan, spacers and heat sink off of the extruder as one piece, and rest them
on the frame of the MakerBot Replicator 2X.
3. Detach the extruder cable from the MakerBot Replicator 2X
The extruder cable is secured with zip ties to the plastic guide at the back of the
extruder carriage and to another guide at the top of the MakerBot Replicator
2X’s back panel. Snip both zip ties to free the cable. Be careful -- make sure you
clip only the zip ties and avoid any of the wires going into the extruder cable.
4. Remove the extruders from the extruder carriage
Use the 2.5 mm hex wrench to remove the two bolts on the underside of the
extruder carriage. There is one bolt all the way at the right of the extruder
carriage and another all the way at the left. Set the bolts aside. Tilt the
extruders to free them from the extruder carriage and set them aside.
5. Turn the MakerBot Replicator 2X onto its left side
To access the Mightyboard, you will need to remove the electronics cavity
cover. Carefully turn your MakerBot Replicator 2X onto its left side so you have a
clear view of the underside of your 3D printer.
6. Remove the electronics cavity cover
The cover is secured with four M3X6 bolts. Use the 2.5 mm hex wrench to
remove them. Set the bolts aside and remove the electronics cavity cover.
Removing Cables from the Mightyboard
In the following steps, you will disconnect the cables that link the extruders to
the Mightyboard. To make connecting the cables from your new extruders
easier, use masking tape and a marker or pen to label the parts of the
Mightyboard where each cable connects. You can also label the cables on your
old extruders as you’re disconnecting them and use them as a visual reference
when you’re installing the new extruders.
7. Detach the main extruder cable from the Mightyboard
The extruder cables from your two extruders are each composed of four pairs of
twisted wires. They connect to the Mightyboard at two ports along the lower
edge of the board, labeled A and B. Use tape and a marker to label the extruder
cable ports before you detach the cables. Gently pull the plastic connectors to
disconnect the cables.
8. Detach the thermocouples from the Mightyboard
The thermocouples from the two extruders attach to a set of terminals at the
lower right of the Mightyboard. These terminals are also marked A and B. Use
tape and a marker to label the terminals before detaching the thermocouples
from the board.
If the terminals are secured by buttons, push the buttons on the terminals to
release the red and yellow leads. If the terminals are secured by screws, use a
small flathead screwdriver to loosen the screws until you can remove the leads.
9. Reattach the fan assembly
Add the heat sink, spacers, fan, and fan guard that you removed in step 2 to the
left extruder. Use the 2.5 mm hex wrench to thread the fan assembly bolts back
into the extruder motor.
10. Set the extruders aside
The extruders are now completely detached from your MakerBot Replicator 2X.
Set them aside and unpack the new extruders.
11. Separate the extruder wires into two bundles
Separate the wires coming from the right extruder from the wires coming from
the left extruder. You may have to unwrap the cable completely to find out
which bundle is which, but it’s very important. Make sure the right and left wire
bundles are labeled before proceeding.
12. Attach the new extruders to the Mightyboard
The new extruders have two thermocouples and two main extruder cables, just
like the old ones. Plug the extruder cables into the ports from which you
removed the old cables. Make sure the right cable is being plugged into the
terminal labeled “A” and the left cable is being plugged into the terminal
labeled “B.”
Next, attach the thermocouples. Make sure you’re inserting the thermocouple
leads into the same terminals you removed the old ones from. The right
thermocouple leads go to the terminals labelled “A” and the left thermocouple
leads go to the terminals labeled “B.” The terminals are also labeled with color
names—be sure to insert the yellow and red leads into the right places.
For terminals with buttons, press the buttons on the terminals, slide the leads
all the way in, and release the buttons. For terminals with screws, slide the
leads in and tighten the screws. Tug on the leads to make sure they're secure.
You may find that it's easier to reconnect one lead at a time.
13. Return the electronics cover to the bottom of your MakerBot
Replicator 2X
Bolt it into place with the 2.5 mm hex wrench and the four bolts you set aside
earlier.
14. Turn your MakerBot Replicator 2X upright again
Make sure the wrapped extruder cable routes through the notch at the back of
the 3D printer.
15. Remove the left fan assembly
Use the 2.5 mm hex wrench to remove the bolts, fan guard, fan, spacers and
heat sink of the left extruder as one piece.
16. Bolt the new extruders onto the extruder carriage
Angle the dual extruders into the extruder carriage. The fans should face the
front of the 3D printer and the motors should face the back. Bolt them into
place using the 2.5 mm hex wrench and the two bolts you set aside earlier.
17. Reattach the left fan assembly
Now that the extruders are on the extruder carriage, you can bolt the fan
assembly into place using the 2.5 mm hex wrench.
18. Push the extruder cable into place
Push the extruders all the way to the front left of the MakerBot Replicator 2X to
ensure that there’s enough slack. Then push the cable into the brackets at the
back of your 3D printer.
That’s it—the new extruders are installed. You can plug in your MakerBot
Replicator 2X, turn it on, load filament and return to printing.
Andere Handbücher für Replicator 2X
8
Inhaltsverzeichnis
Andere MakerBot 3D-Drucker Handbücher
MakerBot
MakerBot Replicator 2X Leitfaden
MakerBot
MakerBot Replicator Z18 Bedienungsanleitung
MakerBot
MakerBot Replicator Mini+ Bedienungsanleitung
MakerBot
MakerBot METHOD Bedienungsanleitung
MakerBot
MakerBot Replicator Bedienungsanleitung
MakerBot
MakerBot Replicator 2X Leitfaden
MakerBot
MakerBot Replicator+ Leitfaden
MakerBot
MakerBot Labs Experimental Extruder Bedienungsanleitung
MakerBot
MakerBot Replicator Bedienungsanleitung
MakerBot
MakerBot Replicator+ Montageanleitung
MakerBot
MakerBot Replicator Mini Compact Bedienungsanleitung
MakerBot
MakerBot Replicator Mini Bedienungsanleitung
MakerBot
MakerBot Replicator 2 Bedienungsanleitung
MakerBot
MakerBot Replicator 2X Stücklistenhandbuch
MakerBot
MakerBot Replicator 2X Bedienungsanleitung
MakerBot
MakerBot Replicator Bedienungsanleitung
MakerBot
MakerBot Replicator Z18 Bedienungsanleitung
MakerBot
MakerBot Replicator 2 Bedienungsanleitung
MakerBot
MakerBot FILAMENT CASE Bedienungsanleitung
MakerBot
MakerBot Sketch Bedienungsanleitung
