MakerBot Replicator Mini+ Bedienungsanleitung

MakerBot Replicator Mini+ Teardown Guide

MakerBot

Tools Needed:

1.3mm Hex Driver

T10 - T20 Torx Driver

2.0mm Hex Driver

1.5mm Hex Driver

2.5 mm Hex Driver

Pair of thin Tweezers

Small Container for Screws

Color Guide:

Button Heads Screw

Action

Thread Forming Screw

Socket Cap Screw

Flat Head Screw

Index

Removing the Covers

Removing the Housing Assembly

Removing the Brooklyn PCB

Removing the Power Supply

Removing the Z Stage Assembly

Removing the Base Cover and Electronics Cover

Motor Cover

Z Carriage Cover

Z Stage Base Cover

Housing

Electronics

Z Stage Assembly

MakerBot Replicator Mini+

MakerBot

MakerBot Replicator

MakerBot

MakerBot Replicator Mini+

Step 1 - Remove Outer Motor

Cover

Grab the Motor Cover and gently

pull away from the Mini. If needed

you can use a small ﬂat head

screw driver, or a tool similar to

it, to make some space between

the Outer and Inner Motor Covers.

Removing the Outer Motor Cover

will expose the screws that attach

the Inner Motor Cover to the

Z-Stage and Spool

Assembly.

Step 2 - Remove Z Carriage

Cover

Grab the Z-Carriage Cover and

slide upward to remove from

Z-stage assembly.

MakerBot Replicator

MakerBot

MakerBot Replicator Mini+

Step 3 - Removing the Z-Stage

Base Cover

Step 4 - Remove Base Cover

and Electronics Cover

Manually rotate the Z-axis rod

clockwise to raise the Build Plate

Holder to give enough clearance

to be able to pull out the Z-Stage

Base Cover and Electronics Cover.

Once the Z-Stage Base Cover is

removed you can slide your ﬁngers

underneath the Base Cover and

pull upwards. You will feel it snap

out of place slide it out of the

Mini+ and set it aside.

Using 1.5mm hex driver remove

the three (3) silver ﬂat head

screws attaching the Electronics

cover and set aside.

With the Base Cover removed you

now have access to the three (3)

silver ﬂat head screws attaching

the Electronics Cover to the Mini+.

Using a small ﬂat head or similar

tool, slide it in the opening near

the threaded lead screw and lift

upwards.

Grab the Z-Stage Base Cover and

pull away from the Mini+.

MakerBot Replicator

MakerBot

MakerBot Replicator Mini+

Step 5 - Remove the Housing

(optional)

Remove the following Screws:

Two (2) thread forming screws

using a T15 driver attaching the

Housing to the Bottom Base.

Eight (8) ﬂathead bolts using a

2.5mm hex driver from the edges

of the Back Panel.

Loosen one (1) socket cap

tensioning bolt by using a 2.5mm

hex driver from the Back Panel.

Two (2) thread forming screws

using a T15.

Three (3) button head screws

using a T15 driver attaching the

Housing to the Bottom Base.

One (1) lock nut and the ground

wire using a 7mm nut driver.

Unplug the Camera Wire from

the Queens PCB located at the

bottom of the Front Panel.

Remove the Gantry Belts from the

Motor Pulleys.

Loosen two (2) button head bolts

located on the rear left Gantry

Motor Mount using a 1.5mm hex

driver.

Unplug Ribbon Cable from the

Queens PCB.

With upward force remove the

Outer Housing Assembly from the

Bottom Base Assembly.

Step 7 - Remove the Brooklyn

PCB

Remove the FFC from the

Brooklyn PCB.

MakerBot Replicator

MakerBot

MakerBot Replicator Mini+

Step 6 - Remove Z-Stage

Assembly

Remove the four (4) thread

forming screw using a T15 driver

located attaching the Z-Stage

Assembly to the bottom base.

Pull the Z-Stage Assembly of

the Housing Assembly upwards

to remove (using a small driver

wedged between the Back Panel

and Frame allows easier removal).

Unplug the limit switch cable from

the Brooklyn PCB.

Unplug the Motor Wire Harness

from the Brooklyn PCB.

Unplug the 10-pin Ribbon Cable

from the Brooklyn PCB.

Unplug the WiFi Antenna from the

Brooklyn PCB.

Unplug 20-pin Power Supply Cable.

Lift up the Brooklyn PCB to remove.

MakerBot Replicator

MakerBot

MakerBot Replicator Mini+

Step 8 - Remove the

Power Supply

Remove three (3) button head

screws from the rear left side of

the Mini+.

Disconnect the twenty-pin

connector from the Brooklyn PCB.

Unclip connector from plastic clips.

Pull Power Supply toward you to

remove it out of the slot.

Andere Handbücher für Replicator Mini+

Inhaltsverzeichnis

Andere MakerBot 3D-Drucker Handbücher

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Sketch Bedienungsanleitung

MakerBot

MakerBot FILAMENT CASE Bedienungsanleitung

MakerBot

MakerBot Replicator+ Leitfaden

MakerBot

MakerBot Replicator+ Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Replicator Z18 Bedienungsanleitung

MakerBot

MakerBot Replicator+ Montageanleitung

MakerBot

MakerBot Replicator 2X Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

MakerBot

MakerBot METHOD Bedienungsanleitung

MakerBot

MakerBot Replicator Z18 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

MakerBot

MakerBot Replicator Mini+ Bedienungsanleitung

MakerBot

MakerBot Replicator 2X Stücklistenhandbuch

MakerBot

MakerBot Smart Extruder+ Bedienungsanleitung

MakerBot

MakerBot Replicator 2X Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Replicator Z18 Bedienungsanleitung

MakerBot

MakerBot Replicator 2X Leitfaden

MakerBot

MakerBot Replicator Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Extruder Installations- und Benutzerhandbuch

MakerBot

MakerBot Replicator+ Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung