Maktec MT871 Bedienungsanleitung

MT871

EN Combination Hammer INSTRUCTION MANUAL 4

ID Bor Getar Kombinasi PETUNJUK PENGGUNAAN 9

Máy Khoan Đa Năng Cầm Tay

Hoạt Động Bằng Động Cơ

Điện

TÀI LIỆU HƯỚNG DẪN 15

TH   20

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

4ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: MT871

Drilling

capacities

Concrete 26 mm

Core bit 68 mm

Diamond core bit (dry type) 80 mm

Steel 13 mm

Wood 32 mm

No load speed 0 - 1,200 min-1

Blows per minute 0 - 4,500 min-1

Overall length 362 mm

Net weight 2.7 kg

Safety class /II

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydifferfromcountrytocountry.

• Weight according to EPTA-Procedure 01/2003

Symbols

The following show the symbols used for the equip-

ment. Be sure that you understand their meaning before

use.

Read instruction manual.

DOUBLE INSULATION

Only for EU countries

Do not dispose of electric equipment

together with household waste material! In

observance of the European Directive, on

Waste Electric and Electronic Equipment

and its implementation in accordance with

national law, electric equipment that have

reached the end of their life must be col-

lected separately and returned to an envi-

ronmentally compatible recycling facility.

Intended use

The tool is intended for hammer drilling and drilling in

brick, concrete and stone as well as for chiselling work.

It is also suitable for drilling without impact in wood,

metal, ceramic and plastic.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and

can only be operated on single-phase AC supply. They

are double-insulated and can, therefore, also be used

from sockets without earth wire.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructionsmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet

5ENGLISH

conditions. Water entering a power tool will

increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

7. Use of power supply via an RCD with a rated

residual current of 30 mA or less is always

recommended.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts.Looseclothes,jewel-

lery or long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application. The correct

powertoolwilldothejobbetterandsaferatthe

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

2. Follow instruction for lubricating and chang-

ing accessories.

3. Keep handles dry, clean and free from oil and

grease.

ROTARY HAMMER SAFETY

WARNINGS

1. Wear ear protectors. Exposure to noise can

cause hearing loss.

2. Use auxiliary handle(s), if supplied with the

tool.Lossofcontrolcancausepersonalinjury.

3. Hold power tool by insulated gripping sur-

faces, when performing an operation where

the cutting accessory may contact hidden wir-

ing or its own cord. Cutting accessory contacting

a “live” wire may make exposed metal parts of the

power tool “live” and could give the operator an

electric shock.

4. Wear a hard hat (safety helmet), safety glasses

and/or face shield. Ordinary eye or sun glasses

are NOT safety glasses. It is also highly recom-

mended that you wear a dust mask and thickly

padded gloves.

5. Be sure the bit is secured in place before

operation.

6. Under normal operation, the tool is designed

to produce vibration. The screws can come

loose easily, causing a breakdown or accident.

Check tightness of screws carefully before

operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for

a while by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difcult.

8. Always be sure you have a rm footing. Be

6ENGLISH

sure no one is below when using the tool in

high locations.

9. Hold the tool rmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area

when operating. The bit could y out and

injure someone seriously.

13. Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

14. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and unplugged before adjusting or

checking function on the tool.

Switch action

CAUTION: Before plugging in the tool, always

check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

CAUTION: Switch can be locked in “ON” posi-

tion for ease of operator comfort during extended

use. Apply caution when locking tool in “ON”

position and maintain rm grasp on tool.

►Fig.1: 1. Switch trigger 2. Lock button

To start the tool, simply pull the switch trigger. Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

For continuous operation, pull the switch trigger, push

in the lock button and then release the switch trigger.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

Reversing switch action

CAUTION: Always check the direction of

rotation before operation.

NOTICE: Use the reversing switch only after the

tool comes to a complete stop. Changing the direc-

tion of rotation before the tool stops may damage the

tool.

NOTICE: If the switch trigger can not be

depressed, check to see that the reversing switch

is fully set to position (A side) or (B side).

►Fig.2: 1. Reversing switch lever

This tool has a reversing switch to change the direc-

tion of rotation. Move the reversing switch lever to the

position (A side) for clockwise rotation or to the posi-

tion (B side) for counterclockwise rotation.

Selecting the action mode

NOTICE: Do not rotate the action mode chang-

ing knob when the tool is running. The tool will be

damaged.

NOTICE: To avoid rapid wear on the mode

change mechanism, be sure that the action mode

changing knob is always positively located in one

of the three action mode positions.

Rotation with hammering

For drilling in concrete, masonry, etc., rotate the action

mode changing knob to the symbol. Use a tungsten-

carbide tipped bit (optional accessory).

►Fig.3: 1. Action mode changing knob

Rotation only

For drilling in wood, metal or plastic materials, rotate

the action mode changing knob to the symbol. Use a

twist drill bit or wood drill bit.

►Fig.4: 1. Action mode changing knob

Hammering only

For chipping, scaling or demolition operations, rotate

the action mode changing knob to the symbol. Use a

bull point, cold chisel, scaling chisel, etc.

►Fig.5: 1. Action mode changing knob

Torque limiter

NOTICE: As soon as the torque limiter actuates,

switch off the tool immediately. This will help pre-

vent premature wear of the tool.

NOTICE: Drill bits such as hole saw, which tend

to pinch or catch easily in the hole, are not appro-

priate for this tool. This is because they will cause

the torque limiter to actuate too frequently.

The torque limiter will actuate when a certain torque

level is reached. The motor will disengage from the

output shaft. When this happens, the drill bit will stop

turning.

7ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION: After installing or adjusting the

side grip, make sure that the side grip is rmly

secured.

Installthesidegripsothattheprotrusionsonthegript

in between the grooves on the tool barrel. Then tighten

thethumbscrewclockwisetoxthegripatthedesired

position.

The side grip can be swung 360° so as to be secured at

any position.

►Fig.6: 1. Side grip 2. Thumb screw 3. Tighten

4. Loosen

Grease

Coat the shank end of the drill bit/chisel beforehand with

a small amount of grease (about 0.5 - 1 g).

This chuck lubrication assures smooth action and lon-

ger service life.

Installing or removing drill bit/chisel

Clean the shank end of the drill bit/chisel and apply

grease before installing the drill bit/chisel.

►Fig.7: 1. Shank end of the drill bit/chisel 2. Grease

Insert the drill bit/chisel into the tool. Turn the drill bit/

chisel and push it in until it engages.

After installing the drill bit/chisel, always make sure that

the drill bit/chisel is securely held in place by trying to

pull it out.

►Fig.8: 1. Drill bit/chisel

To remove the drill bit/chisel, pull the chuck cover down

all the way and pull the drill bit/chisel out.

►Fig.9: 1. Drill bit/chisel 2. Chuck cover

Chisel angle (when chipping,

scaling or demolishing)

The chisel can be secured at the desired angle. To

change the chisel angle, rotate the action mode chang-

ing knob to the O symbol. Turn the chisel to the desired

angle.

►Fig.10: 1. Action mode changing knob

Rotate the action mode changing knob to the sym-

bol. Then make sure that the chisel is securely held in

place by turning it slightly.

Depth gauge

The depth gauge is convenient for drilling holes of

uniformdepth.Loosenthethumbscrewandadjust

thedepthgaugetothedesireddepth.Afteradjusting,

tightenthethumbscrewrmly.

►Fig.11: 1. Thumb screw 2. Depth gauge

NOTE: The depth gauge cannot be used at the posi-

tion where the depth gauge touches against the gear

housing/motor housing.

OPERATION

CAUTION: Always use the side grip (auxiliary

handle) and rmly hold the tool by both side grip

and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

►Fig.12

Hammer drilling operation

CAUTION: There is tremendous and sudden

twisting force exerted on the tool/drill bit at the time of

hole break-through, when the hole becomes clogged

with chips and particles, or when striking reinforcing

rods embedded in the concrete. Always use the side

grip (auxiliary handle) and rmly hold the tool by

both side grip and switch handle during opera-

tions. Failure to do so may result in the loss of control

ofthetoolandpotentiallysevereinjury.

Set the action mode changing knob to the symbol.

Position the drill bit at the desired location for the hole,

then pull the switch trigger. Do not force the tool. Light

pressure gives best results. Keep the tool in position

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at

an idle, then remove the drill bit partially from the hole.

By repeating this several times, the hole will be cleaned

out and normal drilling may be resumed.

NOTE: Eccentricity in the drill bit rotation may occur

while operating the tool with no load. The tool auto-

matically centers itself during operation. This does not

affect the drilling precision.

Chipping/Scaling/Demolition

Set the action mode changing knob to the symbol.

Holdthetoolrmlywithbothhands.Turnthetoolon

and apply slight pressure on the tool so that the tool will

not bounce around, uncontrolled.

Pressing very hard on the tool will not increase the

efciency.

►Fig.13

8ENGLISH

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece. There is a tremendous force exerted on

the tool/drill bit at the time of hole break through.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool. The

drill chuck may be damaged.

Also, the drill chuck will come off when reversing the

tool.

NOTICE: Pressing excessively on the tool will

not speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of your drill

bit, decrease the tool performance and shorten the

service life of the tool.

Set the action mode changing knob to the symbol.

Youcandrillupto13mm(1/2″)diameterinmetaland

upto32mm(1-1/4″)diameterinwood.

Use a drill chuck assembly (optional accessory). When

installing it, refer to the section “Installing or removing

drill bit/chisel”.

►Fig.14: 1. Drill chuck assembly (optional accessory)

To install the drill bit, place it in the chuck as far as it will

go. Tighten the chuck by hand. Place the chuck key in

each of the three holes and tighten clockwise. Be sure

to tighten all three chuck holes evenly.

To remove the drill bit, turn the chuck key counterclock-

wiseinjustonehole,thenloosenthechuckbyhand.

►Fig.15: 1. Chuck key

Diamond core drilling

NOTICE: If performing diamond core drilling

operations using “rotation with hammering”

action, the diamond core bit may be damaged.

When performing diamond core drilling operations,

always set the change lever to the position to use

“rotation only” action.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and unplugged before attempting to

perform inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenanceoradjustmentshouldbeperformedby

Makita Authorized or Factory Service Centers, always

using Makita replacement parts.

9BAHASA INDONESIA

BAHASA INDONESIA (Petunjuk Asli)

SPESIFIKASI

Model: MT871

Kapasitas

pengeboran

Beton 26 mm

Mata bor berteras 68 mm

Mata bor berteras intan

(tipe kering)

80 mm

Baja 13 mm

Kayu 32 mm

Kecepatan tanpa beban 0 - 1.200 min-1

Hembusan per menit 0 - 4.500 min-1

Panjangkeseluruhan 362 mm

Berat bersih 2,7 kg

Kelas keamanan /II

• Karenakesinambunganprogrampenelitiandanpengembangankami,spesikasiyangdisebutkandisinidapat

berubah tanpa pemberitahuan.

• Spesikasidapatberbedadarisatunegarakenegaralainnya.

• Berat menurut Prosedur EPTA 01/2003

Simbol

Berikut ini adalah simbol-simbol yang digunakan pada

peralatan ini. Pastikan Anda mengerti makna masing-

masing simbol sebelum menggunakan alat.

Bacapetunjukpenggunaan.

ISOLASI GANDA

Hanya untuk negara-negara Uni Eropa

Jangan membuang peralatan listrik

atau baterai bersama-sama dengan

bahan limbah rumah tangga! Dengan

memerhatikanPetunjukEropa,tentang

Limbah Peralatan Listrik dan Elektronik

serta pelaksanaannya sesuai dengan

ketentuan hukum nasional, peralatan

listrik yang telah habis umur pakainya

harus dikumpulkan secara terpisah dan

dikembalikan ke fasilitas daur ulang yang

kompatibel secara lingkungan.

Penggunaan

Mesin ini digunakan untuk pengeboran dengan

getar dan mengebor batu bata, beton dan batu serta

pekerjaanpemahatan.

Juga cocok untuk pengeboran tanpa hentakan pada

kayu, logam, keramik dan plastik.

Pasokan daya

Mesin harus terhubung dengan pasokan daya listrik

yang bervoltase sama dengan yang tertera pada pelat

nama,danhanyadapatdijalankandenganlistrikAC

fase tunggal. Mesin diisolasi ganda dan oleh sebab itu

dapat dihubungkan dengan soket tanpa kabel.

PERINGATAN

KESELAMATAN

Peringatan keselamatan umum

mesin listrik

PERINGATAN: Bacalah semua peringatan

keselamatan dan semua petunjuk. Kelalaian

mematuhiperingatandanpetunjukdapat

menyebabkan sengatan listrik, kebakaran dan/atau

cedera serius.

Simpanlah semua peringatan

dan petunjuk untuk acuan di

masa depan.

Istilah “mesin listrik” dalam semua peringatan mengacu

padamesinlistrikyangdijalankandengansumberlistrik

jala-jala(berkabel)ataubaterai(tanpakabel).

Keselamatan tempat kerja

1. Jaga tempat kerja selalu bersih dan

berpenerangan cukup.Tempatkerjayang

berantakan dan gelap mengundang kecelakaan.

2. Jangan gunakan mesin listrik dalam

lingkungan yang mudah meledak, misalnya

jika ada cairan, gas, atau debu yang mudah

menyala. Mesin listrik menimbulkan bunga api

yang dapat menyalakan debu atau uap tersebut.

3. Jauhkan anak-anak dan orang lain saat

menggunakan mesin listrik. Bila perhatian

terpecah, anda dapat kehilangan kendali.

Keamanan Kelistrikan

1. Steker mesin listrik harus cocok dengan

stopkontak. Jangan sekali-kali mengubah

10 BAHASA INDONESIA

steker dengan cara apa pun. Jangan

menggunakan steker adaptor dengan mesin

listrik terbumi (dibumikan). Steker yang

tidak diubah dan stopkontak yang cocok akan

mengurangi risiko sengatan listrik.

2. Hindari sentuhan tubuh dengan permukaan

terbumi atau yang dibumikan seperti pipa,

radiator, kompor, dan kulkas. Risiko sengatan

listrikbertambahjikatubuhAndaterbumikanatau

dibumikan.

3. Jangan membiarkan mesin listrik kehujanan

atau kebasahan. Air yang masuk ke dalam mesin

listrik akan meningkatkan risiko sengatan listrik.

4. Jangan menyalahgunakan kabel. Jangan

sekali-kali menggunakan kabel untuk

membawa, menarik, atau mencabut mesin

listrik dari stopkontak. Jauhkan kabel dari

panas, minyak, tepian tajam, atau bagian

yang bergerak. Kabel yang rusak atau kusut

memperbesar risiko sengatan listrik.

5. Bila menggunakan mesin listrik di luar

ruangan, gunakan kabel ekstensi yang

sesuai untuk penggunaan di luar ruangan.

Penggunaan kabel yang sesuai untuk

penggunaan luar ruangan mengurangi risiko

sengatan listrik.

6. Jika mengoperasikan mesin listrik di lokasi

lembap tidak terhindarkan, gunakan pasokan

daya yang dilindungi peranti imbasan arus

(residual current device - RCD). Penggunaan

RCD mengurangi risiko sengatan listrik.

7. Penggunaan pasokan daya melalui RCD

dengan kapasitas arus sisa 30 mA atau kurang

selalu dianjurkan.

Keselamatan Diri

1. Jaga kewaspadaan, perhatikan pekerjaan Anda

dan gunakan akal sehat bila menggunakan

mesin listrik. Jangan menggunakan mesin

listrik saat Anda lelah atau di bawah pengaruh

obat bius, alkohol, atau obat.Sekejapsaja

lalai saat menggunakan mesin listrik dapat

menyebabkan cedera badan serius.

2. Gunakan alat pelindung diri. Selalu gunakan

pelindung mata. Peralatan pelindung seperti

masker debu, sepatu pengaman anti-selip, helm

pengaman, atau pelindung telinga yang digunakan

untuk kondisi yang sesuai akan mengurangi risiko

cedera badan.

3. Cegah penyalaan yang tidak disengaja.

Pastikan bahwa sakelar berada dalam posisi

mati (off) sebelum menghubungkan mesin

ke sumber daya dan/atau paket baterai, atau

mengangkat atau membawanya. Membawa

mesinlistrikdenganjariAndapadasakelarnya

atau mengalirkan listrik pada mesin listrik

yang sakelarnya hidup (on) akan mengundang

kecelakaan.

4. Lepaskan kunci-kunci penyetel sebelum

menghidupkan mesin listrik. Kunci-kunci yang

masih terpasang pada bagian mesin listrik yang

berputar dapat menyebabkan cedera.

5. Jangan meraih terlalu jauh. Jagalah pijakan

dan keseimbangan sepanjang waktu. Hal ini

memungkinkan kendali yang lebih baik atas mesin

listrik dalam situasi yang tidak diharapkan.

6. Kenakan pakaian dengan baik. Jangan

memakai pakaian yang kedodoran atau

perhiasan. Jaga jarak antara rambut, pakaian,

dan sarung tangan Anda dengan bagian mesin

yang bergerak. Pakaian kedodoran, perhiasan,

ataurambutpanjangdapattersangkutpada

bagian yang bergerak.

7. Jika tersedia fasilitas untuk menghisap dan

mengumpulkan debu, pastikan fasilitas

tersebut terhubung listrik dan digunakan

dengan baik. Penggunaan pembersih debu dapat

mengurangi bahaya yang terkait dengan debu.

Penggunaan dan pemeliharaan mesin listrik

1. Jangan memaksa mesin listrik. Gunakan

mesin listrik yang tepat untuk keperluan

Anda. Mesin listrik yang tepat akan menuntaskan

pekerjaandenganlebihbaikdanamanpada

kecepatan sesuai rancangannya.

2. Jangan gunakan mesin listrik jika sakelar

tidak dapat menyalakan dan mematikannya.

Mesin listrik yang tidak dapat dikendalikan

dengan sakelarnya adalah berbahaya dan harus

diperbaiki.

3. Cabut steker dari sumber listrik dan/atau paket

baterai dari mesin listrik sebelum melakukan

penyetelan, penggantian aksesori, atau

menyimpan mesin listrik. Langkah keselamatan

preventif tersebut mengurangi risiko hidupnya

mesinsecarataksengaja.

4. Simpan mesin listrik jauh dari jangkauan anak-

anak dan jangan biarkan orang yang tidak

paham mengenai mesin listrik tersebut atau

petunjuk ini menggunakan mesin listrik. Mesin

listrik sangat berbahaya di tangan pengguna yang

tak terlatih.

5. Rawatlah mesin listrik. Periksa apakah ada

bagian bergerak yang tidak lurus atau macet,

bagian yang pecah dan kondisi lain yang dapat

memengaruhi penggunaan mesin listrik. Jika

rusak, perbaiki dahulu mesin listrik sebelum

digunakan. Banyak kecelakaan disebabkan oleh

kurangnya pemeliharaan mesin listrik.

6. Jaga agar mesin pemotong tetap tajam dan

bersih. Mesin pemotong yang terawat baik

denganmatapemotongyangtajamtidakmudah

macet dan lebih mudah dikendalikan.

7. Gunakan mesin listrik, aksesori, dan mata

mesin, dll. sesuai dengan petunjuk ini, dengan

memperhitungkan kondisi kerja dan jenis

pekerjaan yang dilakukan. Penggunaan mesin

listrik untuk penggunaan yang lain dari peruntukan

dapat menimbulkan situasi berbahaya.

Servis

1. Berikan mesin listrik untuk diperbaiki hanya

kepada oleh teknisi yang berkualikasi dengan

menggunakan hanya suku cadang pengganti

yang serupa.Haliniakanmenjaminterjaganya

keamanan mesin listrik.

2. Patuhi petunjuk pelumasan dan penggantian

aksesori.

3. Jagalah agar gagang kering, bersih, dan bebas

dari minyak dan gemuk.

Inhaltsverzeichnis

Sprachen:

Andere Maktec Werkzeuge Handbücher

Maktec

Maktec MT660 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung