Malatech EMERALD PRO INDUSTRY Bedienungsanleitung

USER MANUAL

PROFESSIONAL MULTIFUNCTIONAL SOLAR FLOOD LIGHT

WITH 2.4G REMOTE CONTROL

EMERALD PRO INDUSTRY

MANUFACTURER/IMPORTER:

MALATECH WATER, LTD.

1/E Vanyi way, Alsonemedi,

2351 Hungary

+36 30 377 8089

info@malatechsolar.com

LED power: 15 W

Luminous ux: 3 280 lumen

LED chip data: EPISTAR SMD 2835, 192 pcs

Light color: Cold white 6000K

Solar Panel: 10V/50W monocrystalline solar

Li-battery: 6.4V/24 Ah/154Wh LiFePO4 battery

Waterproof IP rating: IP65

Body material: Tempered glass + die-casting Aluminium

Light size: 375X275X52 mm

Solar panel size: 400X670X17 mm

Net weight: 4.45 kg (light head) + 2.75 kg (solar panel)

Charging Time: 4.5 h (considering sucient sunshine during

charging)

Discharging Time: >10h on full capacity (considering full battery

load)

Lighting area: 45-60 m2

Working mode:

By light sensor and remote control (adjustable

brightness, timer, continuous lighting or

motion sensor setup)

Working temperature: -15 - +70 Celsius

Expected battery lifetime: >1500 cycles

Expected LED lifetime: >50,000 hours

Charging methods: 100% solar powered

Remote control: Yes, 2.4G technology remote control

Beam angle: 120 degrees

Motion sensor: Yes, microwave (radar) sensor

Waterproof cable length: 4.5 m

Warranty period: 2 years

Recommended eld of use: Domestic and industrial

Lamp box length/width/height 415X356X89 mm

Solar panel box length/width/height 676X409X26 mm

CONTENT OF THE BOX:

ATTENTION! Battery is built-in, non-replaceable!

ATTENTION! The performance of the battery may drop below 0 Celsius, and

above 40 Celsius temperatures.

Emerald Pro Industr y

ood light (1 pc)

Adapter cable

(4.5 m, 1 pc)

solar panel

(1 pc)

mounting bracket

(stand) (2 pcs)

2.4G remote control

(1 pc)

AAA battery

(2 pcs)

hit-in dowel

(expansion screw)

(4 pcs)

M4*10 screw

(4 pcs)

USER INSTRUCTIONS

1. Instructions, and information about using the battery, and maximizing

its life span:

ATTENTION! The life span of the battery depends on you as well! Please keep

using the product as described in this manual to maximize its life span for your

pleasure:

• Whenever you turn o your light after use, please make sure that

the battery did not run low. If that happens (the light indicates low

voltage by decreasing the luminosity), please load the battery!

• It is recommended to full-charge the light before rst use!

• If you do not use your light for a longer period, please always pay

attention to full-charge the battery ONCE A MONTH! The light can be

stored on the shelf for another month after that. A long-term storage

of the light with totally discharged battery may signicantly reduce

the life span of the battery, or may damage the battery!

ATTENTION! THE STANDBY OPERATION OF THE LIGHT CONSUMES BATTERY

CHARGE AS WELL, WHICH MEANS THAT THE BATTERY IS BEING DISCHARGED

SLOWLY EVEN WHEN YOU DO NOT USE YOUR LIGHT! THAT IS WHY IT IS KEY

ESSENTIAL TO KEEP THE ABOVE WRITTEN INSTRUCTIONS!

2. Instructions for solar charging, information about charging the

battery:

• Please pay attention to keep the solar panel clean. Please follow

“Cleaning instructions” below for cleaning your light!

• Below the LEDs the indicator light keeps blinking until the solar panel

receives enough light for charging. Depending on the level of charge

in the battery the blinking light can be red, yellow or green. Once

the indicator light stops blinking, it means the solar panel does not

receive sucient light to charge the battery. Continuous green light

means the the battery is full-charged.

• In order to maximize the eciency of solar charging, please set the

solar panel to approximately 45 degrees with the solar panel facing

towards the midday sun.

Please pay attention to place your light in a non-shaded place with

sucient sunshine provided for its operation.

ASSEMBLING THE LIGHT & INSTALLATION

Measure and sign the

location of the ood light ’s

bracket (stand) on the chosen

surface. Please care about

the distance bet ween the 2

holes, measure it exac tly.

Tighten the nuts with

a wrench (Care! do not

overtighten!).

Drill the 2 holes (M10)

Place the ood light’s bracket

(stand) onto the screws.

Set up the desired angle of

the ood light, and tighten

the connection ttings (Care!

Do not overtighten!).

Connect the adapter cable to

the connections of the light’s,

and the solar panel ’s cable

connections. Care about

waterproong, connections

must be attached correctly.

Place the hit-in dowels

(expansion screws) in the

holes, and push them in with

a hammer.

Use the 4 pcs M4 screws

to assemble the 2 pcs of L

prole brackets (stands) of

the solar panel.

Loosen the nut, and remove

it together with the 2

washers.

Considering the points

written above, x the solar

panel assembled with its

brackets (stands) on its

chosen location. You nd

2 hit-in dowels (expansion

screws) for xing the solar

panel on the chosen surface.

Place the 2-2 washers on

each screw (spring washer

should be put last), then

drive in the nut on each.

Use the remote-control unit

to operate and customize

your light.

Correct wiring:

Once you connect the ood light with the solar panel, the “AUTO”

operational mode is activated where the solar panel charges the battery

daytime, and the light turns on at dusk. In the morning the light sensor

switches o the light, and starts charging again. Other operational modes

than “AUTO” can be set up by the 2.4G remote control unit.

Functions of the remote control:

You can customize the operation of your light by the 2.4G remote control

unit. Due to 2.4G technology you do not necessarily need to point at the

light with the remote to control it within the operational radius (10-20 m

depending on obstacles). 4 constant lighting options are available with

dierent power setups: 25%, 50%, 75%, and 100% power can be applied.

You can set up time-controlled operations (4h, 6h, 12h), or you can operate

the light with 2 motion sensor setups: light is o, and switches to 100%

power when motion sensor is triggered, or the light shines at 30% power,

and switches to 100% power when motion sensor is triggered. You can

operate the light by the light sensor (AUTO), or you can override the light

sensor operation by pushing the ON/OFF button, which activates daylight

mode.

OPERATING & CUSTOMIZING THE LIGHT,

FUNCTIONS OF THE REMOTE CONTROL

Important notes:

1. If you intend to choose constant lighting with time-control, please set

up the desired power rst (if needed).

2. If you activate any of the 4 power modes, only constant lighting mode

is available.

3. The motion sensor options cannot be altered, you can only add time-

control to these setups.

4. The ood light blinks 2 times shortly whenever it receives a command

from the remote control.

5. With the ON/OFF button you can override AUTO operation, and

operate the light daytime (e.g. at indoor installations).

ON/OFF, manual mode, even daytime

operation can be applied.

Operation by the light sensor. At dusk the

light switches on, early in the morning it

switches o.

Constant lighting modes with 4 dierent

power setups

When activating Test mode, the light switches

on for 60 seconds, then it turns o.

Time-controlled operation (4h, 6h, 12h

operation with constant lighting or by

motion sensor)

Motion sensor operation 1: light is o, and

turns to 100% power when motion sensor is

triggered ( ligh t remai ns on for 60 sec onds a fte r motion is

not detected anymore, t hen it s witches o ).

Motion sensor operation 2: light shines at

30% power, and turns to 100% power when

motion sensor is triggered (lig ht keep s 100% power

for 60 second s after mot ion is not dete cte d anym ore, then it

switches b ack to 3 0% power).

1. After receiving your light, please open the light’s box gently with paying

attention not to cause harm to the light and its parts.

2. Before starting to use your light, please make sure that there are no

visible damages on the light and its parts.

3. If you observe breaking, crack, fracture on the light or on its parts,

please do not use the product, but contact us for replacement.

4. Please do not apply strong physical force on the product that can

damage the light or its parts. Non-ordinary use of the product results

the loss of product warranty.

5. Please keep the box, the packaging material, and the content out of the

reach of children, and pets. There are small objects among the parts

of the light, which children or pets can ingest, or can cause harm to

themselves with.

6. Please do not disassemble the light, do not bend the light, or

apply physical stress on the light. Please follow the user manual’s

instructions for installation, and operation.

7. Do not expose the light to higher heat than natural caused by weather

changes. Excessive heat may damage more constituents of the light.

8. Do not expose the light to continuous high- or low-pressure water

ow, even if you intend to clean your light. The IP65 protection does

not mean you can put the light in water, or you can wash the light with

continuous water stream. The next chapter declares the right method

of cleaning.

9. Please always contact Malatech Water, Ltd, or a professional appointed

by our company if you intend to disassemble the light, remove any

of its parts, or service the light. Service attempts made by users are

prohibited, and result the loss of product warranty.

For preserving the aesthetical outlook, and maintaining the maximum

functionality, and eciency of your light, cleaning is recommended from

time to time. Since the light is operated by solar energy, keeping the solar

panel clean & free of dust is key-essential to ensure its eciency, and

maximize discharging time. Please follow the instructions below when

cleaning your light:

USER INSTRUCTIONS, INFORMATION

CLEANING INSTRUCTIONS

1. Please always use a suitable, soft, and damp towel for cleaning the

solar panel

2. Apply the towel with higher water content for the rst time at each

cleaning procedure to remove the majority of dust preferably with one

movement.

3. After washing the towel in continuous water stream to remove the

accumulated dust, squeeze the water out of the towel, and remove

the remainder of dust with the towel gently from the surface of the

solar panel if necessary. Care to avoid scratching the surface of the

solar panel.

4. If you observe scaling, or other accumulated dirt on the surface of the

solar panel, please only use a chemical or natural enzymatic based

agent for cleaning which is recommended for solar panel cleaning by

its manufacturer.

5. Cleaning of the plastic and metal parts of the light body can be

executed easily, but attention is needed to avoid scratching of the

surfaces.

6. Cleaning the dome which protects the LED group from external eects

also requires cautious approach for cleaning to avoid scratching.

Please apply chapter 1)-4) above for the dome as it is written in case

of the solar panel.

The light recognizes low battery voltage, and switches o automatically

to prevent the battery from damage, and to maximize the life cycle of the

battery. Besides that, the light applies an eco-mode when the battery

level is low but sucient for operation. In this case the light will shine at

a dimmed mode. Please charge your light whenever any of the above

written occurs!

The WEEE (Waste Electrical and Electronic Equipment) sign

means that every electrical, and electronic wastes must

be collected, and treated separately. According to The

Waste Electrical and Electronic Equipment Directive (WEEE

Directive), the European Community Directive 2012/19/EU

on waste electrical and electronic equipment (WEEE) which, together with

the RoHS Directive 2011/65/EU lights, and light bodies are electrical, and

AUTOMATIC BATTERY PROTECTION

WASTE DISPOSAL

Inhaltsverzeichnis

Andere Malatech Scheinwerfer Handbücher

Malatech

Malatech EMERALD 100 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung