Malouf POWER-FLEX 2 Bedienungsanleitung
OWNER’S MANUAL
POWER-FLEXTM 2POWER-FLEXTM 2
OWNER’S MANUAL
POWER-FLEXTM 2
iii
ELECTRICAL
•Carefully remove Take care not to damage the bed frame or any included
•Carefully read and follow the set up and installation instructions included with the
PACEMAKERS
•This product is for use on a standard
•Always use a electrical surge protection device with this This product should
be plugged directly into the surge protection device and the surge protection device should be
plugged directly into a wall
•Only connect this product to a properly grounded
•Always unplug this bed from the electrical outlet before cleaning or
•Never operate with a damaged cord or Keep the cord away from this product’s moving
•Keep the cord away from heated
•Do not use this product
•Some pacemakers may detect motion by this product as a false sense of movement or exercise. This may or may
not affect your pacemaker. Talk to a physician to address any concerns.
•Immediately dispose of all packing materials that may pose a suffocation risk.
•Do not allow children or pets to play on or under the bed. Children should not operate this
product without adult supervision.
•This product is designed solely for in-home use and not as a hospital bed. The product has not been tested to
meet hospital standards. Do not use with oxygen or other flammable gasses.
•Power-Flex 2
•This product will support the recommended weight limits when weight is distributed evenly across the This
product is not designed to support or this amount in the head or foot sections Consumers should not
enter or exit the bed when any portion of it is in the raised Do not sit on the head or foot sections while
in the raised Exceeding the recommended weight restrictions or other misuse of this product could
damage the bed and void the
WARNINGS
OWNER’S MANUAL
POWER-FLEXTM 2
iviii
PRODUCT
RATINGS
• Power-Flex 2
co
Esh nty
• This product is designed to have no maintenance requirements by the Please do not open
any motor alter the modify the or change the product in any way as
it will void the
•
•
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
• Operates on GHz frequency
• To comply with the FCC RF exposure requirements, no change to the antenna or the device is permitted. Any change
to the antenna or the device could result in the device exceeding the RF exposure requirement and void user’s right
to operate the device.
For any questions or concerns regarding this product please contact ®
OWNER’S MANUAL
POWER-FLEXTM 2
viv
CONTENTS
Overview
Assembly
Synchronizing Two Bases
Electrical Components and Backup Battery
Test All Functions / Additional Help
Warranty Information
Remote Control
1 2
OVERVIEW
Power-Flex 2
Retainer Bar Power Supply Box
Power Cord
() -Inch Legs
(6) End Caps
() Leg Sets Included
with King Size
() -Inch Legs
Wireless Remote Control
USB Ports
Head Motor Foot Motor
Control Box
Sync Cable
(included with Split sizes only)
OWNER’S MANUAL
POWER-FLEXTM 2
OWNER’S MANUAL
POWER-FLEXTM 2
3 4
ASSEMBLY
Place the box in the room the bed will be used with the bottom of the box facing
Carefully remove packaging taking care not to puncture the box with any
sharp
Remove the bed base from the box and set mattress side down on the floor
Remove all plastic and zip All components and parts are located
in the underside of the Remove attached parts and set aside in preparation for
assembly Check to make sure all parts have been included and are not
damaged
A minimum of two people are required to assemble this adjustable
Open box on the floor in the flat bottom facing to avoid
B
A
King Size Only
6
OWNER’S MANUAL
POWER-FLEXTM 2
5
ASSEMBLY
A
C
Hand tighten all six legs for King into the bed frame until Note
that there are two location options for each an outside placement or an inside
Tighten the legs in the location of your maintaining a consistent
inside or outside location Take care not to over tighten
To reach a height from the floor to the top of the deck use a
leg
Install the power cord by connecting the cord jack to the receptacle on the bed
motor Be sure the cord is connected completely and
Middle Leg on King Size Only
Foot
Head
Leg Positions
B
7 8
ASSEMBLY
With two to four the bed by the metal frame and turn it over so the
mattress side is facing up Take caution not to the bed with the
or to use the legs as pivot points causing angled pressure as this may cause
Move the bed to the desired
A
OWNER’S MANUAL
POWER-FLEXTM 2
9 10
ASSEMBLY A
To install the mattress retainer insert one end of the retainer bar in its respective
slot until it slides fully into place Flex retainer bar to insert the other end
on the other
Plug the power cord into the wall outlet and run the test on pages of this
You may want to familiarize yourself with the remote control functions
prior to running the
OWNER’S MANUAL
POWER-FLEXTM 2
11 12
REMOTE
CONTROL Overview
All of the functions of the bed can be operated with the remote The remote
control comes with buttons that will automatically adjust when
or you can manually control adjustments using the arrow buttons on the remote
See the diagram to the right for a complete list of remote control
Remove the battery cover on the back side of the remote Insert the two included
AAA batteries
Zero Gravity and Anti Snore are both positions that can be adjusted
and saved to match your Simply adjust your bed to the desired then
hold down the Flat then simultaneously press the position button you want to
A
Head Up
Head Down
Preset Zero Gravity Position
or Programmable Position A
Flat
Preset Anti Snore Position
or Programmable Position B
Foot Up
Foot Down
B
OWNER’S MANUAL
POWER-FLEXTM 2
Andere Malouf Massagegerät Handbücher
