Mando Footloose user manual 06
English
A new way of moving 07
Adjustment of the
product
Adjustment of the handlebar
Mando Footloose has a foldable handle system for which you can adjust
the angle of the handlebar and its height.
1.Setting the handle height
The height at which a rider feels comfortable when going up and down a
slope or cornering
- If the handle is too low you may experience backache, neck pain or wrist
pain during a ride.
- If the handle is too high you may find the handling is unsteady during a ride.
2. How to adjust the handle height
- Loosen the lever of the handlepost clamp located under the handlebar.
- Adjust the handle to the desired height.
- After ensuring the alignment of the handle, tighten the clamp lever.
- Note : The tightness of the lever may be adjusted with the adjustment of a
screw on the other side of the clamp to the lever.
3. Finding the right angle of the handlebar
While holding the handlebar with the clamp bolts, set the angle of the handle
at which you can perform throttling and braking comfortably. Then re-tighten
the clamp bolts.
- If the angle of handle is not properly set, it may cause finger or wrist pain.
- Place fingers on the brake levers and adjust the angles so they lie parallel to
the extension line of the arm.
- Setting the angle of brake lever: Adjust it with the brake lever clamp bolts.
- Setting the angle of the throttle lever: Adjust it with the throttle bolts.
4. Adjustment of the brake lever
If it is hard to grab the handle due to your hand size, it is encouraged to
contact the store or a specialist to adjust the lever reach.
C-2
1) Check whether the sit front is on
the straight line with the handle post.
2) If the sit moves or goes down with the
lever closed, turn the nut beside the
clamp to clockwise
Note
It is important to adjust the brake prop-
erly so you can easily reach the brake
lever. It is recommended to set the brake
at which produces the best braking
power within the adjustment range of
the brake lever reach.
• If the brake lever reach is too short:
you may find it too stiff or hand pain.
• If the brake lever reach is too long:
it may not produce the best braking power.
Minimum insertion line
Handlepost clamp
How to adjust the seat post
1) Open the seat clamp lever
completely.
2)Adjust the height of the seat
post that fits the user (Do not
pull out the seat post beyond
the minimum insertion depth).
3)Close the lever.
Adjustment of seat height
For riding Mando Footloose, it is important to place the seat properly and
adjust the height. When adjusting the seat, adjust (1) the height first and then
(2) the front and back part of the seat.
1. Adjusting the seat up and down
How to check the seat height
1) Sit on the seat.
2) Put one heel on the pedal.
3) Adjust the seat height so that your heel is parallel to the axis of pedal and
you can almost straighten your leg (However, it is not recommended to
straighten your leg completely).
4) Get into and off from the seat when the product is standing.
Enquire at the store to learn how to adjust the optimum seat height. If you
would like to adjust the seat height by yourself, you have to ensure the fol-
lowing.
5) Ensure that the seatpost clamp is tightened properly.
6) Ensure that the seat post is not above the ‘minimum insertion’ line.
7) Ensure that the seat is not twisted to one side.
8) Ensure that the seat is properly clamped to the seatpost.
2. Adjusting the seat forward and backward
As the seat is adjustable in forward and backward directions, it enables an
optimal seat position.
For proper operation and better charging efficiency when pedaling with
Mando Footloose, it is recommended to set the pedal position so it can rotate
continuously. Adjust the seat forward and backward by aligning the imaginary
line vertically drawn from knee cap with the axis of pedal. Within this range,
find the most comfortable position.
3. Adjusting the seat angle
Most riders prefer the seat parallel to the ground. However, some prefer to
raise or lower the front part of the seat. If you have pain while sitting on the
seat, lowering the front part of the seat may help reduce it (however, the
center of gravity may move to the front).
The seat fastening clamp of Mando Footloose is in the form of 2 bolts; 1
at the front and 1 at the back. Adjust the seat to ensure that the seat lies
horizontally or at a preferred angle by screwing the front and back bolts in
turns. A little difference gives a large effect on the performance and comfort of
Mando Footloose.
Although the seat height has been properly adjusted, you may feel uncom-
fortable while riding if the slope and front/back position of the seat are not
balanced. Also, the seat provided with the product may not fit to your body. In
this case, it is encouraged to ask assistance of a specialist at the store.
C-1
Adjustment of the
product
The first point to consider before a ride
is to adjust Mando Footloose to your
body. Proper adjustment allows comfort-
able riding and safety. Should you have
any difficulty with the adjustment, please
contact the store. Even though you
have completed the fitting (adjustment
of Mando Footloose to yourbody) with
proper skills and tools, it is encouraged to
confirm your adjustment with the store.
Adjustment of the seat
Minimum insertion line
If Mando Footloose is improperly fitted,
you may lose control or get injured such
as joint injury during a ride.
The seat is designed for general sizes;
therefore, it does not correspond to every
rider’s pelvic shape and sitting habits. If
you are unable to find a comfortable posi-
tion, and it causes consistent pain even
after seat adjustment, it is encouraged to
replace it with another type of seat.
After seat adjustment ensure that it is se-
cured properly before riding. before rid-
ing. Loosely placed seat clamp or seat-
post clamp may cause damage to the
seatpost. Due to this damage, you may
lose control and fall off the bike.
In some cases, riding with a improperly
positioned seat may cause minor or se-
vere injury (e.g. It may chafe skin and
cause prostate pain/numbness, knee
pain, etc) Should you feel uncomfortable
or have pain, stop riding and visit the
store for specialist assistance.
Tighten clamp bolts properly. Loosely
screwed bolts may cause wobbling and
fatigue during a ride, or may cause you to
fall off from the bike.
