Manrose Quiet Fan Series Montageanleitung

QF100SX5OP Manrose Quiet Fan X5 S

QF100TX5OP Manrose Quiet Fan X5 T

QF100HTX5OP Manrose Quiet Fan X5 HT

QF100PIRX5OP Manrose Quiet Fan X5 PIR

PLEASE READ THESE INSTRUCTIONS IN CONJUNCTION WITH THE ILLUSTRATIONS.

PLEASE SAVE THESE INSTRUCTIONS.

Installation and Wiring Instructions

Quiet Fan Range

220-240V~50Hz

IPX5

Installation and Wiring Instructions for the Quiet Fan Range

IMPORTANT: READ THESE INSTRUCTIONS BEFORE COMMENCING THE

INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

SAFETY AND GUIDANCE NOTES

All wiring to be in accordance with the current I.E.E. Regulations,

or the appropriate standards of your country and

MUST

installed by a suitably qualified person.

The Fan is suitable for installation within Zones 1 & 2.

The Fan should be provided with a local isolator switch capable of

disconnecting all poles, having a contact separation of at least

3mm.

Ensure that the mains supply (Voltage, Frequency, and Phase)

complies with the rating label.

The Fan should only be used in conjunction with the appropriate

Manrose products.

The Fan should only be used in conjunction with fixed wiring.

When the Fan is used to remove air from a room containing a fuel-

burning appliance, ensure that the air replacement is adequate for

both the fan and the fuel-burning appliance.

The Fan should not be used where it is liable to be subject to direct

water spray for prolonged periods of time.

Where ducted Fans are used to handle moisture-laden air, a

condensation trap should be fitted. Horizontal ducts should be

arranged to slope slightly downwards away from the Fan.

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they do not play with

the appliance.

Stationary appliances not fitted with means for disconnection from

the supply mains having a contact separation in all poles that

provide full disconnection under over voltage category III, the

instructions state that means for disconnection must be

incorporated in the fixed wiring in accordance with the wiring rules.

Ensure the grille is fully engaged onto the fan chassis using all

clips.

Cleaning and user maintenance shall not be made by children.

ACCESSORIES (not supplied)

WALL FITTING KIT

A range of 100mm wall kits are available for installing into most walls using liners supplied.

INSTALLATION

IMPORTANT: The fan should only be used in

conjunction with fixed wiring.

PANEL/CEILING MOUNTING

1. For panel/ceiling mounting the fan should be installed into a closed duct protected by an exterior air

grille that must comply with the standard requirements of your country.

2. Cut a 105mm diameter hole for 100mm fans.

3. Push the two clips on each side of the fan and pull the grille away from the chassis.

4. Mark the screw centres through the holes in the fan back plate. Drill, plug and screw into position.

5. After installation, ensure impeller rotates freely and the shutters can open.

6. Replace the grille and ensure the clips reactivate.

WALL MOUNTING

1. For wall mounting either cut a 115mm diameter hole for 100mm fans, through the wall and insert the

wall sleeve. Slope the sleeve slightly downwards away from the fan. Cut to length and cement both

ends into position flush with the wall faces.

2. Push the two clips on each side of the fan and pull the grille away from the chassis.

3. Mark the screw centres through the holes in the fan back plate. Drill, plug and screw into position.

Fix exterior grille into position with the louvres positioned downwards. (Note:- The grille must

comply with the standard requirements of your country. The wall kit used in this installation should

provide a minimum ducting length of 100mm from the fans back plate to the inside of the external

grille).

4. After installation, ensure impeller rotates freely and the shutters can open.

5. Replace the grille and ensure the clips reactivate.

WIRING

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST

BE ISOLATED FROM THE POWER SUPPLY DURING THE

INSTALLATION / OR MAINTENANCE.

IMPORTANT

The fan should only be used in conjunction with fixed wiring.

The cross - sectional area of supply cord used should be ranged from 0.75-1.5mm2.

Cable entry can be made from the rear or the side of the fan using the grommet provided.

The extraction fan is suitable for connection to 220-240V ~ 50Hz supply.

The fan is a class ll double insulated product and MUST NOT be earthed.

1. Select and follow the appropriate wiring diagram. (Fig. 1, 2 or 3)

2. Check all connections have been made correctly and ensure all terminal connections are securely

fastened.

3. Ensure the impeller rotates and is free from obstructions.

SETUP

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE

ISOLATED FROM THE POWER SUPPLY DURING THE INSTALLATION / OR

MAINTENANCE.

See Fig 1, 2, 3, 4, 5, 6 & 7

QF100SX5OP – Single speed fan. Controlled by remote switch (e.g light switch or auto sensor) Fig.1.

QF100TX5OP – Single speed fan with overrun Timer* - The fan can be wired to a lighting circuit switch.

Fig.3. or wired for a basic on/off operation wire as Fig 2.

When switched ‘ON’, the fan will operate at full speed and will continue to run for a pre-set time after the

switch is turned ‘OFF’ Overrun timer adjustable 5-30min. See Fig.6.

QF100HTX5OP - Single speed fan with Humidity Timer* - The fan contains an integral humidity sensor.

In automatic mode the fan switches on when the room Relative Humidity (RH) increases. The fan will

continue to run until the room RH falls. These fans also include a built in overrun timer function that is

adjustable between 5-30 min. See Fig.7.

QF100PIRX5OP - PIR* - Single speed with PIR (passive infra-red) detector and overrun timer. The fan

starts automatically when a movement is detected and will continue to operate for the set overrun time

period. Fig. 1.

The fan can also be wired to a lighting circuit switch. Fig.3. so it can be started by the light switch or the PIR

detector. For timer adjustment see Fig.5.

*All timer versions require a third switch live wire for the timer to work.

SERVICING AND MAINTENANCE

WARNING: THE FAN AND ANCILLARY CONTROL

EQUIPMENT MUST BE ISOLATED FROM THE POWER

SUPPLY DURING MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no

build-up of dirt or other deposits.

2. Wipe the inlets and front face with a damp cloth until clean.

The fan has sealed for life bearings, which do not require lubrication.

Fig.1:

QF100SX5OP & QF100PIRX5OP

Fig.2:

QF100TX5OP & QF100HTX5OP (Timer / Humidistat disabled)

220-240V

~ 50Hz

3 AMP

MAX

220-240V

~ 50Hz

3 AMP

MAX

Fig. 5: PIR TIMER

To remove the grille, push both clips on each

side (1)

Timer Adjustment

Fig.3: QF100TX5OP, QF100HTX5OP & QF100PIRX5OP

Fig.6: QF100TX5OP

Timer Adjustment:

To REDUCE the operating time, use a small

screwdriver to turn the adjuster ANTI-CLOCKWISE.

To INCREASE the operating time, use a small

screwdriver to turn the ad

uster CLOCKWISE.

220-240V ~ 50Hz

3 AMP

MAX

Timer

Adjustment

Timer Adjustment

To REDUCE the operating time, use a small

screwdriver to turn the adjuster ANTI-CLOCKWISE.

To INCREASE the operating time, use a small

screwdriver to turn the adjuster CLOCKWISE.

Fig.7:

QF100HTX5OP

Disposal

This product should not be disposed of with household waste. Please recycle where facilities

exist. Check with your local authority for recycling advice.

Timer Adjustment

To REDUCE the operating time, use a small screwdriver

to turn the adjuster ANTI-CLOCKWISE.

To INCREASE the operating time, use a small screwdriver

to turn the adjuster CLOCKWISE.

Humidity Adjustment

To INCREASE SET POINT, turn the adjuster

CLOCKWISE. This makes the controller LESS

sensitive.

To REDUCE SET POINT, turn the adjuster

ANTI-CLOCKWISE. This makes the controller

MORE sensitive.

Humidity

Adjustment

Timer

Adjustment

Manrose Manufacturing

Unit 23, 53 Suttons Park Avenue

Earley

Reading

RG6 1AZ

EU Authorised Representative: Manrose Bedrijvenweg 17 7442 CX Nijverdal Nederland authorisedrep@manrose.nl

496934 A 0621

Contact Information

Website: www.manrose.co.uk

email: [email protected]

Sales hotline: 01753 691399

Technical hotline: 01753 876941

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Manrose Lüfter Handbücher

Manrose

Manrose LED Series Bedienungsanleitung

Manrose

Manrose COMT Series Bedienungsanleitung

Manrose

Manrose HYPER150 EC Bedienungsanleitung

Manrose

Manrose CRA100T Bedienungsanleitung

Manrose

Manrose FAN2040 Bedienungsanleitung

Manrose

Manrose FAN0090 Bedienungsanleitung

Manrose

Manrose 100T Montageanleitung

Manrose

Manrose PURO DCT4565 Bedienungsanleitung

Manrose

Manrose FAN7180 Bedienungsanleitung

Manrose

Manrose FAN2120 Bedienungsanleitung

Manrose

Manrose intellivent 2.0 Bedienungsanleitung

Manrose

Manrose EXTRACT-A-LITE Service-Handbuch

Manrose

Manrose LED Series Bedienungsanleitung

Manrose

Manrose PRO Series Bedienungsanleitung

Manrose

Manrose LED Series Installationsanleitung

Manrose

Manrose FAN7187 Bedienungsanleitung

Manrose

Manrose MRUF150WH Montageanleitung

Manrose

Manrose VIVO FAN7291 Bedienungsanleitung

Manrose

Manrose PRO Series Bedienungsanleitung

Manrose

Manrose MANI3000N Montageanleitung

Manrose

Manrose FAN7191 Bedienungsanleitung

Manrose

Manrose HYPER150 Bedienungsanleitung

Manrose

Manrose FAN0616 Bedienungsanleitung

Manrose

Manrose CLASSIC XF125 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung