Maple Systems HMC4101A-M Series Bedienungsanleitung

[Panel Cutout Dimensions: 256.00(W) x 178.00(H)mm,

Panel Thickness: Maximum 6mm and Mounting Clamps: 6]

Tighten the mounting screws evenly to a torque between 0.4N/m

to maintain water and dust resistance.

Power (Base)

24VDC(±15%), 270mA, 6.48W

Power

(with 5 Expansions)

24VDC(±15%), 520mA, 12.48W

Display

10.1”, 1024 x 600pixels, WSVGA color TFT with

4-wire analog resistive touch screen

LEDs

RAM Memory

512MB

User Application

Up to 1GB that includes user application, data

log, alarms, retentive memory and logic

memory

Internal Datalog

50 MB

eMMC

4GB

RTC

Built-in, date and time function

Expansion

Supports 5 expansion slots

Weight

Approx. 900gm

Product Dimensions

268.0(W) x 190.0(H) x 36.8(D)mm

Panel Cut-out

256.00(W) x 178.00(H)mm

Communication

COM1 and COM2

2 x RS232/RS485

USB Ports

1 USB Type C Port and 1 USB Host Port

Ethernet

1 Ethernet Port

SD Card

Micro SD [High Capacity (4GB to 32GB)]

Speed Class:

[While inserting and removing SD card, please make

sure to TURNOFF the power to the unit.]

Environment & Approvals

Operating

Temperature

0° to 50°C

Storage Temperature

-20° to 85°C

Humidity

10 to 95% (Non-Condensing)

Shock

IEC 60068-2-27

25g, 11ms, 6 shocks per axis, total 18 shocks (X,

Y, Z)

Vibration

IEC 60068-2-6

5 to 150Hz, 3g peak (X, Y, Z)

EMC

EN 55011 : 2009/A1 : 2010

EN 61131-2 : 2007

EN 61000-6-2 : 2005/AC : 2005

EN 61000-6-4 : 2007/A1 : 2011

Protection

IP66 for front panel mounting

APPROVALS

CE, UL (Class1 Div2) & RoHS

SPECIFICATIONS

PRODUCT DIMENSIONS

QUICK START GUIDE

HMC4101A-M Series

Product Description:

HMC4101A-M: 1024 x 600, WSVGA, 10.1” color TFT with

4-wire analog resistive touch screen with 2 comm port,

one USB Type C port, one USB Host port, 1 Ethernet Port

& SD card slot. It supports up to 5 expansions.

Contents:

1ea HMC4101A-M (bagged and sealed)

1ea Mounting kit (4ea mounting clips)

1ea Input Power connector plug

1ea Quick Strat Guide

Perform the following steps to configure and use the

HMC4000 Series unit:

1. Install MAPware-7000 software.

2. Create your project.

3. Connect a programming cable (USB or Ethernet).

4. Save your project.

5. Download project to HMC4101 (note: you must select

the Download Firmware option for the initial download).

6. The HMC4000 unit is ready to use in the system.

GETTING STARTED

For More Information, visit

https:\\www.maplesystems.com

AW-10114101AM Rev. 00, 02/18/22

USB Host Port

1. USB Host, compliant with USB 2.0 specification

2. USB Host can be used to transfer logged data and historical alarm

to USB memory stick.

3. USB Host can handle only USB memory stick devices and can

source current up to 150mA only.

4. Connector used: Standard USB Type a Female connector.

Pin number

Signal

VCC

D-

D+

GND

Cable Diagrams

PC to unit programming cable (RS232):

2 Wire RS485 connections:

4 Wire RS485 connections:

Earthing

The optimum method for Earthing electronic equipment is to earth

it separately from other high-power systems, to earth more than one

unit of electronic equipment with a single-point earth. The Earthing

marked terminal (see below) is provided on the unit.

[Note: Do not use an earth that has an unstable impedance, such as painted

screws or earth subject to vibration.]

This section provides information regarding communication interfaces

supported by this product.

COM1 & COM2: RS485/RS232/RS422

DB9 Female

Pin number

Signal

TX+(RS422/RS485)

TXD(RS232)

RXD(RS232)

RX+(RS422/RS485)

GND

TX-(RS422/RS485)

RX-(RS422/RS485)

Ethernet Port

1. Fully compliant with IEEE 802.3 / 802.3u standards.

2. 10/100 Mbps support.

3. Connector used: Standard shielded RJ-45 female jack with in-built speed

and link activity indication LEDs.

Pin number

Signal

TX+

TX-

RX+

RX-

USB Type C

1. USB Type C, compliant with USB 2.0 specification, self-powered device.

2. Connector used: Micro USB Type C Female connector.

WARNING:

-> This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D

or non- hazardous locations only.

-> WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless

power has been removed or the area is known to be non-hazardous.

-> WARNING – EXPLOSION HAZARD - Substitution of components may impair

suitability for Class I, Division 2.

-> WARNING - CAUTION, Battery May Explode If Mistreated. Do Not Recharge,

Disassemble or Dispose of in Fire.

-> The list of materials used in the construction of these devices with name of

sealed device - generic name of the material and the supplier's name and type

designation.

-> It is recommended that the user periodically inspect the sealed devices

used, for any degradation of properties and Replace the device if any

degradation is found.

Rev.

Description

Date

Initial release

02/18/2022

Maple Systems Inc® reserves the right to change or discontinue

specifications and features without prior notice.

To view the latest and updated datasheets/manuals, please visit

www.maplesystems.com.

REVISION HISTORY

AW-10114101AM Rev. 00, 02/18/22

HMC Unit side (COM2)

HMC4101A-M

CONTROL DRAWING NO# CNTL/DWG/1011-4101AM

Andere Maple Systems Touchscreen Handbücher

Maple Systems

Maple Systems OMI6900BP Series Bedienungsanleitung

Maple Systems

Maple Systems PC100 Series Bedienungsanleitung

Maple Systems

Maple Systems HMC7070A-M Bedienungsanleitung

Maple Systems

Maple Systems OMI6912A Bedienungsanleitung

Maple Systems

Maple Systems HMC7043A-M Bedienungsanleitung

Maple Systems

Maple Systems Ivory Series Bedienungsanleitung

Maple Systems

Maple Systems PC2315A Bedienungsanleitung

Maple Systems

Maple Systems Silver Plus Series Bedienungsanleitung

Maple Systems

Maple Systems OMI6800 Series Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung