Marani LPP260A Gebrauchsanweisung

LPP260A Quick User's Guide

Before to install the setup.exe, please make sure that the Net Framework 4.0 is already installed on

the PC used.

After install the setup.exe and run the app “LPP260A then the system show the following window

and after few seconds the main window

Below is introduction for the “Device List :

: Connect all device

: Disconnect all device

: Add device to the List

: Remove one or more device from the List

: Search Device

: Device Name

: Connection status of the device, by double clicking this characters, user can switch between

“On-line and “Off-line mode.

Click the icon, you will see below conversation window. Click the preferable connection mode and

device model. (In this case, device model shall be “LPP260A )

Note: When you connect under TCP/IP mode, please input the IP address of the device; if under

RS485 mode, please input the ID of the device as well.

Once you have confirm the information, click “OK to finish, and you will see the name of device you

just added, as below image shows. Double click the device name, you will see the editing page.

You can also add the device into the “Device List with the icon, set configuration in below boxes

according to your connection mode, so to Search and connect the device.

The User has the possibility to connect the device via USB or RS485 or TCP/IP

* If the USB is selected, the User must set the number of the COM used to connect the device

By the way, using the button “Check the Sw will scan the Pc ports looking for the potentially

connected ones: set on the Com Select window the found Com ports until found the working one.

In order to use the USB connection for remotely controlling the LPP260A, need first set on the unit

the communication interface as USB.

To set the USB interface on the LPP260A the following steps have to be done:

1. press the “PM3/UTILITY button on the front panel, for entering the “UTILITY MENU

2. use the “PM1/ENTER encoder for selecting the “Interface Utility field

3. press the “PM1/ENTER button, for entering the “Interface Setup field

4. use the “PM2/ESC encoder, for selecting the USB interface

5. after operated the selection, press the “PM2/ESC button the necessary times for moving back

on the several fields up to the default screen, showing “LPP260A and the current loaded

preset

* If the RS485 is selected, the User must set the number of the COM used to connect the device and

the ID number set on the device. When the RS485 is used and the User want connect several devices

then if important that all device have an unique ID otherwise some device can not working

Use the button “Check to see all COM connected on the PC.

In order to use the RS485 connection for remotely controlling the LPP260A, need first set on the unit

the communication interface as RS485 and assign an ID to the unit.

To set the RS485 interface on the LPP260A the following steps have to be done:

1. press the “PM3/UTILITY button on the front panel, for entering the “UTILITY MENU

2. use the “PM1/ENTER encoder for selecting the “Interface Utility field

3. press the “PM1/ENTER button, for entering the “Interface Setup field

4. use the “PM2/ESC encoder, for selecting the RS485 interface

5. use the “PM3/UTILITY encoder, for selecting the RS485 interface's ID number

6. after operated the selection, press the “PM2/ESC button the necessary times for moving back

on the several fields up to the default screen, showing “LPP80A and the current loaded preset

* If the TCP/IP is selected, the User can click the icon, and select “TCP/IP Mode in the checkbox as

below image suggests, and input the device IP address range:

In order to use the TCP/IP connection for remotely controlling the LPP260A, need first set on the unit

the communication interface as TCP/IP and assign an IP address to the unit, if not used DHCP mode. t

To set the TCP/IP interface on the LPP260A the following steps have to be done:

1. press the “PM3/UTILITY button on the front panel, for entering the “UTILITY MENU

2. use the “PM1/ENTER encoder for selecting the “Interface Utility field

3. press the “PM1/ENTER button, for entering the “Interface Setup field

4. use the “PM2/ESC encoder, for selecting the TCP/IP interface

5. use the “PM3/UTILITY encoder, for selecting the DHCP mode On/Off

6. if set the DHCP mode OFF, press the “PM1/ENTER button fo entering the field for the IP

address assignment

7. after operated the selection, press the “PM2/ESC button the necessary times for moving back

on the several fields up to the default screen, showing “LPP260A and the current loaded

preset

Once decided the Interfacing Connection and set the necessary parameters there where required,

from the all USB. RS485 and TCP/IP windows, press the button “OK and the system will start to check

the device(s).

When found the connected device(s) the Sw will show a list of the devices found (if no device are

found then is possible to continue in demo mode “Off-line ) on the window “Device List .

If no devices found, the Sw will ask if the user want to continue in demo mode for evaluating the

available process of the LPP260A.

to edit the device, double click on the name of the device present on the “List ID

EDITI G Windows

on the Edit window is possible edit all parameters of the Input and output Output channel, save and

load configuration on the sw PC, copy the input channel to another input channel, insert and change a

User password in order to lock/unlock the interface, link the channel and see the current version of

the firmware and software.

On the ALL Editing Windows, the Top Bar is fixed and shows ever the several available “tools'' useful

for the User to manage the Editing Job so as to save it on Pc or within the unit.

TOOL BAR

Load: Load a previously saved Full Configuration from a defined Pc directory. The configuration

loaded will be the one edited with its parameters set on the several editing windows. The

configuration loaded is containing the ALL parameters set in the several Editing Windows

Save: Save the current Full Configuration (the all parameters set within the all Editing Windows) into a

defined Pc directory. The saved configuration is containing the ALL parameters set in the several

Editing Windows

Store: Save the current Full Configuration (the all parameters set within the all Editing Windows) into

one of 16 available locations within the LPP260A. The saved configuration is containing the ALL

parameters set in the several Editing Windows and can be recalled also from the unit's front panel.

Recall: Load a previously saved Full Configuration from one of 16 available locations within the

LPP260A. The configuration loaded will be the one edited with its parameters set on the several

editing windows.

Copy (located after Recall): tool for copying the all parameters of one input channel to an other one.

The Phase Correction FIR, available on each Input Path, are not included in this copy tool.

Copy (located before Default): tool for copying the all parameters of one output channel to an other

one. The Xover FIR, available on each output Path, are included in this copy tool. The Routing

available on each couple of outputs (1/2, 3/4) is not included in the copy tool.

Default: tool which can be used to bring back the LPP260A to the default setup, which is matching the

one got by the Hw reset. All parameters are flatted and the all outputs are in MUTE

User (password selection): by default (when released by the factory) the password for locking

permanently the LPP260A is set as “000000 . Using the USER tool, the user can define is own

password of six characters. Just providing at the very beginning the password “000000 . a windows is

entered allowing the user to assign a new password and confirm it.

Lock: momentary lock of the units' controls. When set, the all parameters cannot be accessed by the

user, but no password is required for setting/resetting the lock itself. Used for avoiding to accidentally

modify a setting during a live performance or if the user need to leave the editing session

momentarily.

Password: this tool is allowing to LOCK the LPP260A by Password. When the unit is locked providing a

Password, no control is accessible and to exit this status it is necessary to provide again the password

allowing so to UNLOCK the unit.

Link Input: this powerful tool is giving to the user the possibility, checking the related boxes, to LINK

together 2 or more input channels. When two or more input channels, with their own particular

setting of parameters, are linked, from the link moment ahead the all parameters set to one of the

linked channel will be set in the same way also on the other linked channels. The link function is not

affecting the status of the parameters of the linked channels, preceding the Link action.

Link Output: as for the inputs, this tool is giving to the user the possibility, checking the related boxes,

to LINK together 2 or more output channels. When two or more output channels, with their own

particular setting of parameters, are linked, from the link moment ahead the all parameters set to one

of the linked channel will be set in the same way also on the other linked channels. The link function is

not affecting the status of the parameters of the linked channels, preceding the Link action.

R: button allowing to access the ROUTING Main Editing Page

G: button allowing to access the GAINS Main Editing Page

A/B: buttons allowing to access the INPUT CHANNELS Editing Pages

1/2/3/4/5/6: buttons allowing to access the OUTPUT CHANNELS Editing Pages

i: info button, giving information about the Firmware and Pc Sw version.

ROUTI G WI DOW

This Window is guesting a synoptic image of the several processes available on the Input and Output

paths of the LPP260A, so as a series of “frames for the selection of Input sources and Signal Routings.

Input Source frame: The Signal Sources to the LPP260A inputs can be selected in between several

options, in alternative to each others.

- Analog Input is selecting as Inputs for the LPP260A, the ANLOG INPUT coming from the XLR

Balanced connectors on the unit's back panel. The max accepted input level for the Analog Inputs is

+20dBu.

- Digital Input is selecting as Inputs for the LPP260A, the DIGITAL INPUT coming from the XLR

connectors CHA and CHB on the unit's back panel. In order to select the Digital Inputs, need the inner

button located in between the ChC Input and CH1 Output to be pressed.

- oise Generator is selecting as Inputs for the LPP260A, the White or Pink Noise generated internally

by the Unit and controlled in Level by the related Slider ranging from -40dBu up to 0dBu.

Inhaltsverzeichnis

Andere Marani Steuerungssystem Handbücher

Marani

Marani LPP240A Gebrauchsanweisung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung