Marantz RC9200 Bedienungsanleitung
User Guide
To the RC9200/RC5200
Touch Screen Remote Controls
Automating Your
Home Theater
With Marantz
Automating Your Home Theater With The Marantz RC9200/5200
RC9200/5200 Remote Control User Guide
The in ormation in this manual is copyright-protected. No part o this manual may be
copied or reproduced in any orm without prior written consent rom Marantz America,
Inc.
MARANTZ AMERICA, INC. CORPORATION SHALL NOT BE LIABLE FOR OMIS-
SIONS OR FOR TECHNICAL OR EDITORIAL ERRORS CONTAINED IN THIS
MANUAL. MARANTZ AMERICA, INC. SHALL NOT BE HELD LIABLE FOR INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE SUPPLYING OR
USE OF THIS INFORMATION. MARANTZ AMERICA, INC. SHALL NOT BE HELD
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE PERFORMANCE OR USE OF THE MATERIALS DESCRIBED IN THIS MANU-
AL.
The in ormation in this manual may be subject to change without prior notice.
All other brand or product names are trademarks or registered trademarks o their
respective companies or organizations.
FCC NOTICE: This equipment has been tested and ound to comply with the limits or
a Class B digital device, pursuant to part 15 o the FCC rule. These limits are
designed to provide reasonable protection against harm ul inter erence in residential
installation. This equipment generates, uses, and can radiate radio requency energy
and , i not installed and used in accordance with the instructions, may cause harm ul
inter erence to radio communications. However, there is not guarantee that inter eren-
ce will not occur in a particular installation. I this equipment does cause harm ul inter-
erence to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the inter erence by one
or more o the ollowing measures:
nReorient or relocate the receiving antenna.
nIncrease the separation between the equipment and receiver.
nConnect the equipment into an outlet on a di erent circuit rom the receiver.
nConsult the dealer or an experienced radio/TV technician or help.
Note I serial or parallel ports are con igured, a iltered/shielded serial or paral-
lel cable is recommended to minimize EMI and ensure FCC class B
compliance.
User Guide
1
Introduction 2
1. The Marantz RC9200/5200 2
2. Battery 3
Getting Started 6
1. Activating the RC9200/5200 6
2. Navigating Control Panels 7
3. Operating a Device 12
4. Adjusting the Settings 13
5. The Mode Menus 15
6. Managing Memory 17
Customizing Your RC9200/5200 18
1. Introduction 18
2. Programming Remote Codes 18
3 Deciding between Macros or Help Lists 20
4. Programming Help Lists 22
5. Macro/Panel Jump Capabilities 23
6. Programming Macros & Panel Jumps 24
7. Programming Macros as a Device Action 26
8. Protecting Your Work rom Changes 27
Re erence 28
1. Programming Buttons 28
2. Labeling Buttons, Frames and Menu Items 32
3. Working with Device and Macro Groups 35
4. Deleting and Restoring 40
5. Recording Macros 43
6. RC5000 Setup 47
Troubleshooting 49
Frequently Asked Questions 52
Overview o Symbols 54
Speci ications 56
The Revert Con iguration 57
Index 58
Table of Contents
User Guide
2
The RC9200/5200 is designed to control most devices that understand
in rared remote control signals. Its easy-to-use touchscreen and its intuiti-
ve inter ace make it a per ect remote control or every user. The
RC9200/5200 is completely customizable and programmable. You can
add devices and unctions, relabel buttons, record macros and animate
your macros. Although the RC9200/5200 is pre-programmed or Marantz
components, a vast collection o built-in tab guided panels with pre-arran-
ged button art enables you to easily choose the per ect inter ace or any
non-Marantz component. The RC9200/5200 easily learns commands
rom the vast majority o manu acturers remote controls.
Introduction
1. The Marantz RC9200/5200
The Volume, Channel
and Mute buttons are
typically programmed to
always work the same
way regardless o what
panel is displayed.
The In rared Eye
transmits to your
devices and learns
rom your existing
remotes.
The Touchscreen
The INFO button
enables you to check batte-
ry li e.
Scroll Up and Scroll Dn but-
tons duplicate the unction
o the scroll arrows and are
easier to ind in the dark
(they navigate between
panels when there are more
than one panel or control-
ling a speci ic devicde).
\Menu, Enter, Exit and 4
way navigator buttons will
change their unction
depending on what device
you are controlling.
The Contrast Dial
adjusts the appe-
arance o the
screen.
The Backlight but-
ton lights up the
screen (you can
adjust the length o
time it stays on,
see page 13).
The Serial Port ena-
bles you to program
the RC9200/5200
on a Windows PC.
The Home B utton
always takes you
back to the Main
Home Panel Control
Screen (think o it
as the Start button).
User Guide
3
Introduction
Tap the Mode Button:
to access the Mode
Menus. They are di e-
rent based on the type
o panel you last dis-
played. Use the Mode
Menus to customize
your remote.
Devices
Macros Home
Tap the Scroll Arrows:
to scroll to other panels within the
active group.
Tap the Macro menu Bar:
to use your one touch
Macro buttons. Tap again
and a menu o all o your
Macro groups appears.
Tap again to select:
Tap the Device
menu bar:
to operate devices.
Tap again and a
menu o all your
devices appears.
Tap again to select:
Panel number:
shows active
control panel
Tap the Scroll Arrows:
to scroll to other
panels within the acti-
ve group.
2. The Battery
When you use the Remote Control or the irst time, you will have
to:
¥ install the battery pack;
¥ place the Remote Control in the docking station and charge the
Remote Control.
¥ tap the INFO button on the Home Panel to check battery
li e.
Warning Use the docking station only with the Philips NiMH rechargeable
battery pack.
We strongly advise you not to plug other appliances (like mobile
phones, PDA s, ) into the docking station. This will damage both
the connector and the appliance.
Use the Control Panel
Buttons:
to operate your compo-
nents
User Guide
4
Installing the Battery Pack
1 Press the latch on the battery cover and remove the battery
cover rom the Remote Control.
2 Place the battery pack in the battery compartment.
3 Plug the cable o the battery pack in the connector as illustrated.
4 Place the battery cover back on.
Note Make sure the cable o the battery pack does not get stuck
between the molded interior and the battery cover.
A ter a ew seconds, the Remote Control starts up automatically
and an Introduction screen appears. The Remote Control beeps
twice to indicate that it has inished starting up.
Because the battery pack o the Remote Control is not ully pre-
charged, you will have to charge it as described below.
Introduction
User Guide
5
Charging the Remote Control
For charging the Remote Control you use the docking station.
1 Plug the power adapter into a wall outlet and connect it to the
docking station.
2 Place the Remote Control in the docking station.
Make sure you hold the Remote
Control at an angle o 30¡ to 45¡
when you place the it in the
docking station.
Charging starts immediately. The green charging LED on the
ront o the docking station indicates charging takes place.
When the Remote Control is ully charged, the LED goes o .
Note Normal charging time is 2 to 3 hours, depending on the
condition o the battery pack.
You can operate the Remote Control while it is being charged.
The battery pack does not have to be entirely empty be ore
recharging.
You can place the Remote Control in the docking station at any
time.
When the battery pack is running low, the Low Battery icon lashes
at the top o the screen. Recharge the Remote Control as soon as
possible to ensure per ect per ormance.
Note The RC9200/5200 retains all settings when the AA batteries have
run out. You will only have to reset the clock.
Introduction
User Guide
6
Turning on the Display
Tap the screen gently with your inger or a blunt, so t object like
a pencil eraser.
The display is activated and you see the Home panel.
Notes ÆI the display stays blank or becomes black, adjust
the contrast dial on the le t side.
ÆI another panel is displayed, tap the Home button .
ÆThe RC9200/5200 shuts down automatically.
Using the Backlight
Press the backlight button on the le t side.
The backlight shuts o a ter a ew seconds to save power.
Note In the settings (see page 13) you can choose to activate the
backlight automatically when you turn the RC9200/5200 on.
Use Mode
The RC9200/5200 has di erent modes. When you activate the
RC9200/5200 or the irst time, it starts up in Use mode allowing
you to immediately operate your devices.
In Use mode the menu bar at the top o the screen is visible . I a
label (like or ) covers the icon, just tap the label. A menu
will pop up with USE as an option. Tap the USE to return to normal
operating mode.
Getting Started
1. Activating the RC9200/5200
User Guide
7
Three Divisions o Control Panel Types
Your RC9200/5200 is capable o displaying hundreds o di erent
control screens. By grouping them into sensible divisions, it is easy
to navigate to the control panel you want. The three main divisions
are:
Home The Home group disp-
lays convenient instant jump buttons
to the main control panels o your
system devices (your VCR, TV, CD
player etc.). These buttons
also select the Input o your Home
Theater Receiver or Preamp (Home
buttons are linked to the Device
pull down menu, which also selects
inputs on your receiver).
Access Home by tapping
the Home button at the
bottom le t o the remote.
D evices The Device side
displays the control panels o your
components, one device group at a
time. A button on a Device panel
will act just like the buttons on the
original remote control.
You can always select the Device
side o the RC9200/5200 by tapping the
menu bar to the right o the remote
icon.
Getting Started
2. N avigating Control Panels
Tap to select the Device side o your
RC9200/5200 .
User Guide
8
Macros The Macro side o your
RC9200/5200 displays Macro buttons.
Macro buttons play back a sequence
o up to 255 di erent commands (and
panel jumps, which can be pro-
grammed to give status during the
Macro).
You can always select the Macro side
o the RC9200/5200 by tapping the menu
bar to the le t o the remote icon.
Using Menus to Jump to a Panel Group
1 Navigate to either the Macro (le t) or the Device (right) side o
the remote by tapping the le t or right menu bar.
2 Tap the Menu bar again. A menu will pop into view, enabling you
to choose which group o panels you want. I you have a large
system with more than seven groups, scroll arrows enable
you to select those that are out o sight.
3 A ter using the scroll arrows to view all o the choices, simply
tap the label o the group you would like.
Note When you jump to a Device, the RC9200/5200 will change the
input o your home theater receiver/preamp (using the pull down
menus is exactly the same thing as pressing a Home button).
Getting Started
Tap to select the Macro side o your
RC9200/5200.
Device Groups
Macro Groups
Andere Handbücher für RC9200
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Marantz Fernbedienung Handbücher
Marantz
Marantz RC1200 Betriebsanleitung
Marantz
Marantz RC2001 Bedienungsanleitung
Marantz
Marantz RC2000MKII Bedienungsanleitung
Marantz
Marantz RC5200 Bedienungsanleitung
Marantz
Marantz Professional RC600PMD Bedienungsanleitung
Marantz
Marantz RC101 Kurzanleitung
Marantz
Marantz RC2001 Bedienungsanleitung
Marantz
Marantz RC-1400 Bedienungsanleitung
Marantz
Marantz RC3200 Bedienungsanleitung
Marantz
Marantz RC-9500 Bedienungsanleitung
Marantz
Marantz RC-5400 Bedienungsanleitung
Marantz
Marantz RC5000i Bedienungsanleitung
Marantz
Marantz RC101 Bedienungsanleitung
Marantz
Marantz RC2000MKII Bedienungsanleitung
Marantz
Marantz RC-9500 Bedienungsanleitung
Marantz
Marantz RC-5400 Bedienungsanleitung
Marantz
Marantz RC-1400 Bedienungsanleitung
Marantz
Marantz RC-1400 Bedienungsanleitung
Marantz
Marantz RC5000i Bedienungsanleitung
Marantz
Marantz RC3001 Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
