Mark 7 Evolution Bedienungsanleitung

Mark 7® Evolution Autodrive

User Manual v 1.1

Read this manual completely. Understand all safety and operating instructions. Failure to

comply with the warnings and instructions may result in serious injury, illness or death.

reserved

Table of Contents

Table of Contents .........................................................................................................................................2

Important Safety Instructions...................................................................................................................3

Box Contents ................................................................................................................................................5

Set-Up Procedures........................................................................................................................................6

1. Removal of equipment from the packing carton.................................................................................. 7

2. Mouting Evolution Press to baseplate..................................................................................................8

3. Mounting large sprocket.......................................................................................................................9

4. Belt installation...................................................................................................................................10

5. Belt Guard installation ........................................................................................................................11

6. Tablet holder install ............................................................................................................................ 12

7. Tablet cable outlet installation ...........................................................................................................13

8. Console Rear I/O inputs ...................................................................................................................... 14

9. Console Side I/O inputs.......................................................................................................................15

10. EMI FILTER for Bulletfeeders ............................................................................................................16

11. Manully Driving the press ................................................................................................................17

Operating Instructions: ..............................................................................................................................18

Digital Clutch Setting............................................................................................................................... 21

.................................................................................................................................26

Sensors........................................................................................................................................................27

.........................................................................................................................27

..........................................................................................................................28

DECAPSense (Optional).......................................................................................................................... 31

PRIMER ORIENTATION SENSOR .............................................................................................................34

Sofware Firmware Updates .......................................................................................................................39

Autodrive Maintenance Intervals..............................................................................................................41

Storage Recommendations........................................................................................................................42

System Errors ............................................................................................................................................43

Troubleshooting .......................................................................................................................................43

Important Safety Instructions

Read this manual completely prior to installation and operation. Understand all safety and operating

instructions. Failure to comply with the WARNINGS and instructions may result in serious injury or

death. WARNINGS throughout this manual will be symbolized by the yellow WARNING symbols seen

below.

WARNING –Activities using the Mark 7® Evolution Autodrive are inherently dangerous and may lead to

injury and even death. Actions as a result of using the Mark 7® product are solely the responsibility of

the user –if you get injured through the reloading process or through the use of ammunition as a result

of the reloading process it is your fault.

WARNING - Mark 7® equipment should only be operated by trained personnel that follow all safety

precautions. Failure to do so could result in serious injury or death.

WARNING - This product is designed to be used by reloading personnel in conjunction only with a fully

functioning and well lubricated EvolutionTM reloading press. Its use should be limited to experienced

personnel only. This document contains basic operating and maintenance instructions only.

WARNING - Never leave your Mark 7® Autodrive unattended while it is operating.

WARNING –Never run the Mark 7® Autodrive without the belt guard fully attached to the baseplate.

reserved

WARNING –Never operate the Mark 7® Autodrive while impaired.

WARNING –Never operate the Mark 7® Autodrive without using high quality brass and always use

sufficient lubrication on your brass while operating the Mark 7® Autodrive.

WARNING –The Mark 7® Autodrive is designed to help automate the process of loading and processing

of ammunition. Never operate the Mark 7® Autodrive at speeds higher than you have tested and are

comfortable with for the type of reloading or processing that you are undertaking. Run the Mark 7®

Autodrive at the slowest possible setting to create quality ammunition.

WARNING –Always wear protective eyewear to protect eyes from being injured. Flying debris may

result when using this equipment. Always wear protective clothing that covers arms, legs and neck to

protect from injury.

It is the responsibility of the user to ensure that appropriate protective clothing and equipment are used

to provide protection from those hazards to which personnel are exposed or could be exposed while

working with this product. Failure to do so could result in serious injury or death

Box Contents

Please review these contents and inform us right away if you appear to be missing any of these items:

Main: Mark 7® EvolutionTM Autodrive Assembly (1 item)

Lower Insert:

Left Side: Power Cable (1 item)

Right side: Pocket 1: Large Sprocket and Cap (2 items)

Pocket 2: Hardware (16 items)

•Link Bar

•¼-20 X 1.25”socket Cap Screws (2X)

•3/8-24 X 1.25” Set screw (1X)

•3/8-24 X 1.75”Socket Cap Screws (4X)

•3/8-24 hex jam nut (1X)

•10-24 Thumb Screw (3X)

Middle Insert: (8 items)

•SwageSense® Sensor

•PrimerSense® communication cable

•Cable management (zip ties, zip tie mounts) (4X each)

•Tablet holder with right angle brackets and plugs (1X)

•Tablet mount (1X)

•Micro-USB Cable (1X)

•EMI Filter kit for bulletfeeder (1X)

•MicroSD Card: for software updates (1X)

Top Insert: (4 items)

•Tablet (1X)

•Belt (1X)

•Belt guard (1X)

•Setup instructions (1X)

reserved

Set-Up Procedures

Prior to installation perform the following manual press checks and adjustments (see EvolutionTM User

Manual for location of some of the items below):

1. Ensure that the press/Autodrive combination is on a very solid surface that does not move. The

Mark 7 Autodrive is designed to sit on the 4 rubber feet in the corners, but it can also directly be

bolted to your work bench by removing the 4X rubber feet in the corners, use ¼-20 bolts to

fasten the baseplate to the work surface from underneath. Small vibrations can have an

unpredictable impact on the operation of the machine. Ensure that the machine does not move

whatsoever when operating.

2. Ensure that the press operates according to EvolutionTM specifications defined in the user

manual before you install the Autodrive. Ensure that the shell plate retaining collar is adjusted

so that the shell plate turns freely but is not too loose. Ensure that the index pawl enables the

shell plate to move completely from one index position to the next. Refer to the press user 's

manual for the location of the pawl adjustment screw. Verify that the alignment pins pass

cleanly into their respective holes and are not used to complete the index motion.

3. Check that there is no powder or other debris under the shell plate. Lubricate the press as

described in the EvolutionTM user's manual. Keep the shellplate clean.

4. There will likely be three (3) cables coming from the machine: the power to the case feeder,

bullet feeder, and Autodrive. For best performance we recommend to keep the case feeder

and Mr.Bulletfeeder cables separated from our system cables if possible.

WARNING -Only use Mark 7® accessories with the Mark 7® Autodrive. Mark 7® equipment is prepared

and tested by Mark 7® prior to delivery. To place the equipment into service, please review the

following instructions carefully.

WARNING - In order to ensure proper operation and avoid damage to your press perform the pre-

installation steps.

1. Removal of Main Autodrive assembly from the packing carton

Upon removal carefully inspect contents for damage. Damage that occurs during shipment should be

reported immediately to the carrier. Major system components listed below.

Figure 1: Major Component Overview

Electronics

Console

Base Plate

Rubber Feet

(4 Corners)

Drive

Sprocket

Motor Mount

Belt Tensioning

shoulder Bolt

Gear Box

Motor

reserved

2. Mounting Evolution to Baseplate

Remove the Handle from the EvolutionTM and place the Press on front of the Autodrive baseplate in the

orientation shown below. Using the 4X 3/8-24 by 1.75” Socket Cap Screws secure the press to the

baseplate. Be mindful not to drag the bottom of the press against the baseplate.

Figure 2 : Mounting to Baseplate

Mounting

Hardware (QTY 4)

Leave Shaft

Adapter Installed

3. Mounting Large Sprocket

Insert the link arm through the shaft Adapter then fasten the sprocket to the link bar with the 2X ¼-20

socket cap screws. Once the sprocket is secured insert the sprocket cap and thread in the 3/8 Set screw

to lock in the link bar. Lock the set screw in place with the jam nut using a 9/16” socket.

Figure 3: Mounting Large Sprocket

reserved

4. Belt installation

Loosen both motor mount hex bolts with a 9/16”wrench and move the Motor Assembly towards the

Press. Place the belt over the Large sprocket then around the small sprocket. Put the handle between

the shoulder screw on the baseplate and the front of the motor mount and pry to tension the belt. Lock

down the motor mount.

Figure 4: Installing the belt

WARNING

Belt must be properly tensioned for the drive to operate correctly and safely. Belt tension should be

checked periodically –A properly tensioned belt should have about a ¼” of slack between the two

sprockets.

Andere Handbücher für Evolution

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mark 7 Gleichstromantrieb Handbücher

Mark 7

Mark 7 1050 Series Bedienungsanleitung

Mark 7

Mark 7 650 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung