Marmitek IP EYE ANYWHERE 10 - SOFTWARE ULTRAVIEW Sicherheitsleitfaden
I
P CAMER
A
SERIES
IP CAMERA
SERIES
IP Eye Anywhere - 10 - 11 - 20 - 21
IP RoboCam - 10 - 11 - 21
20244 / 20080709 • IP Eye Anywhere™ / IP RoboCam™
ALL RIGHTS RESERVED MARMITEK ©
3
Software User Guide
ULTRAVIEW
SOFTWARE USER GUIDE - 1 -
Contents
INTRODUCTION............................................................ 2
INSTALLATION.............................................................3
USING ULTRA VIEW ..................................................6
TO LAUNCH THE PROGRAM ........................................................... 6
ITEM FEATURES............................................................................. 7
TO ADD A MARMITEK IP EYE ANYWHERE CAMERA.................... 12
TO REMOVE A MARMITEK IP EYE ANYWHERE CAMERA ............ 15
TO LINK TO THE WEB PAGE OF THE CAMERA ............................. 15
TO RECORD VIDEO ...................................................................... 16
TO CONFIGURE THE RECORDING SETTINGS............................... 18
TO PLAYBACK THE RECORDED VIDEO ........................................ 20
TO SET UP MOTION DETECTION OPTIONS................................... 21
INFORMATION .............................................................................. 23
MARMITEK
- 2 -
INTRODUCTION
This Software User Guide provides detailed instructions on
operating Ultra View, a customized software application with a
user-friendly interface allowing you to access and control your
Marmitek IP Eye Anywhere and IP Robocam camera(s). You can
connect up to 16 cameras to monitor different places and record
events for each camera. With Ultra View, you can also change
some basic settings of the camera, such as schedule profiles and
motion detecting. In addition, if your camera supports advanced
features, such as audio or pan/tilt function, you can use these
functions through the control panels of Ultra View.
To use Ultra View, you have to install it in your computer. It is
recommended to use a high performance computer if you want to
connect multiple cameras simultaneously. The following provides
the system requirements:
Platform: Microsoft® Windows® 2000/XP/Vista/7.
Hardware Requirement:
1 camera connected: Intel Pentium III 800MHz; 512MB RAM
2 ~ 4 cameras connected: Intel Pentium 4 1.3GHz; 512MB
RAM
5 ~ 8 cameras connected: Intel Pentium 4 2.4GHz; 1GB RAM
9 ~ 16 cameras connected: Intel Pentium 4 3.4GHz; 2GB
RAM
Resolution: 1024x768 or above
NOTE When you use Ultra View to record video clips, store the
recorded files to an exclusive hard disk drive in your
computer to ensure that there will be enough storage
space.
INSTALLATION
Firstly, insert the Installation CD-ROM into the CD drive of your
computer to initiate the Auto-Run program. The Auto-Run screen
provides the following buttons:
zQuick Guide
zAdvanced Guide
zSoftware Manual
zIP Finder
zInstall Software
zBrowse
zExit
To start installing:
1. Click Install Software and then select Ultra View. The setup
wizard appears to help you complete the installation step-by-
step.
NOTE To use Ultra View, you must have Microsoft .NET
Framework 2.0 installed in the computer. The setup wizard
will detect it and, if the program is not installed yet, ask you
to install it during the process of installing Ultra View.
SOFTWARE USER GUIDE - 3 -
2. On the welcome screen, click Next.
3. Click Browse to select the destination location to install the
software; otherwise, leave the default setting and click Next.
MARMITEK
- 4 -
4. Click Next again to confirm installation. The setup wizard
starts to install the software and the progress bar indicates
the installation is proceeding.
5. Installation is completed. Click Close.
SOFTWARE USER GUIDE - 5 -
USING ULTRA VIEW
To launch the program
This section describes the user interface and operating
instructions of Ultra View. To launch the program, click Start >
Programs > UltraView > UltraView, and the main screen will
appear as below:
NOTE Please set the resolution to 1024x768 or above on your
computer while using Ultra View; otherwise, the displayed
main screen may be distorted.
MARMITEK
- 6 -
Item features
The following describes the function of each item on the main
screen:
CONTROLS Panel
-SETTING: Click to enter the Setting screen of Ultra View.
Click again to return to the main screen of Ultra View.
-PLAY: Click to play the recorded video file using the media
player on the computer (for example, Windows Media
Player by default).
-LOCK: Click to lock the camera controls. Click again to
resume controls for the camera. If you have set ID and
Password in SETTING > Account, you will be asked to
enter the required information to unlock.
-ALL RECORD: Click to start recording video clips using all
connected cameras. Click again to stop recording and save
the files in the computer. When you connect only one
camera, this button’s function is the same as the RECORD
button.
TIP By default, the ID and Password boxes are “blank.” Click
SETTING > Account to change the ID and password of
lock/unlock function.
SOFTWARE USER GUIDE - 7 -
VIEW SELECTION Panel
-View mode buttons: Ultra View provides multiple view
modes, including 1/4/9/16 windows and Full screen mode.
-SCAN: When you connect multiple Marmitek IP Eye
Anywhere or IP Robocam cameras, click this button to
display the video views as the main window in turn.
-PREV: When you connect multiple Marmitek IP Eye
Anywhere or IP Robocam cameras, click this button to
switch the video view to the previous camera.
-NEXT: When you connect multiple Marmitek IP Eye
Anywhere or IP Robocam cameras, click this button to
switch the video view to the next camera.
TIP To set the time interval of scanning, click SETTING >
Other and then adjust the time from 1 to 10 seconds in the
Time interval of scan option.
MARMITEK
- 8 -
CAMERA Panel
-TRIGGER OUT: Click to turn on the trigger out connector of
the Marmitek IP Robocam camera. This button is available
only when the connected camera supports the trigger out
connector, which is used to control the external device
connected to the camera, such as a light.
-SNAPSHOT: Click to capture a still image using the
selected Marmitek IP camera and save the file in the
computer.
-RECORD: Click to start recording a video clip using the
selected Marmitek IP camera. Click again to stop recording
and save the file in the computer.
-TALK: Click to speak out through the Marmitek IP
Robocam 21 camera. This button is available only when the
connected camera supports 2-way audio function.
-LISTEN: Click to receive the on-site sound and voice from
the Marmitek IP Eye Anywhere 20, 21 or IP Robocam 21
camera.
SOFTWARE USER GUIDE - 9 -
Dieses Handbuch passt für folgende Modelle
6
Inhaltsverzeichnis
Andere Marmitek IP-Kamera Handbücher
Marmitek
Marmitek IP EYE ANYWHERE 241 - ADVANCED Bedienungsanleitung
Marmitek
Marmitek IP Robocam 8 wireless Original Betriebsanleitung
Marmitek
Marmitek IP EYE ANYWHERE 10 Bedienungsanleitung
Marmitek
Marmitek IP EYE ANYWHERE - SOFTWARE ULTRAVIEW Sicherheitsleitfaden
Marmitek
Marmitek IP EYE ANYWHERE 10 Bedienungsanleitung
Marmitek
Marmitek robodome10 Bedienungsanleitung
Marmitek
Marmitek IP RoboCam541 Bedienungsanleitung
Marmitek
Marmitek IP EYE ANYWHERE 10 Bedienungsanleitung
Marmitek
Marmitek IP RoboCam Bedienungsanleitung
Marmitek
Marmitek IP EYE ANYWHERE 241 - ADVANCED Bedienungsanleitung
