Marmitek SS13 Bedienungsanleitung

SS13

LIMLINE WIRELES

SWITCH

USER MANUAL 3

GEBRAUCHSANLEITUNG 10

GUIDE UTILISATEUR 16

MODO DE EMPLEO 23

MANUALE D’ISTRUZIONI 30

GEBRUIKSAANWIJZING 37

20146/20061012 • SS13TM SLIMLINE WIRELESS SWITCH

SS13

SLIMLINE WIRELESS

SWITCH

2©MARMITEK

USER MANUAL SS13™

WIRELESS SWITCH

SAFETY WARNINGS

• To prevent short circuits, this product should only be used inside and

only in dry spaces. Do not expose the components to rain or moisture.

Do not use the product close to a bath, swimming pool etc.

• Do not expose the components of your systems to extremely high

temperatures or bright light sources.

• Do not open the product: the device contains live parts. The product

should only be repaired or serviced by a qualified repairman.

• In case of improper usage or if you have opened, altered and repaired

the product yourself, all guarantees expire. Marmitek does not accept

responsibility in the case of improper usage of the product or when the

product is used for purposes other than specified. Marmitek does not

accept responsibility for additional damage other than covered by the

legal product responsibility.

• This product is not a toy. Keep out of reach of children.

• Batteries: keep batteries out of the reach of children. Dispose of

batteries as chemical waste. Never use old and new batteries or

different types of batteries together. Remove the batteries when you

are not using the system for a longer period of time. Check the polarity

(+/-) of the batteries when inserting them in the product. Wrong

positioning can cause an explosion.

• Automatic switching devices provide comfort, but can also be

dangerous. They can surprise people or can ignite clothing hanging

over an electric heat source. Please be careful and take appropriate

measures to avoid accidents.

How does Marmitek X-10 work?

Marmitek X-10 components use the existing mains wiring to communicate

(using Marmitek X-10 signals). You can build a complete system using the

three different kind of components of the Marmitek X-10 System:

3SS13TM

ENGLISH

1. Modules: These components will receive Marmitek X-10 signals and

will switch or dim the attached lamp or appliance.

2. Controllers: These components will transmit Marmitek X-10 signals and

thus will control the Modules.

3. Transmitters: Wireless components like remotes. The signals of these

components will be received by a controller with transceiver

functionality (IRRF 7243, TM13 or console of a Marmitek

Security System).

The Transceiver will translate the signals into Marmitek X-10

signals on the power line.

Addresses

Up to a maximum of 256 different addresses can be preset. These are

subdivided into a so-called HouseCode (A to P incl.) and a UnitCode (1 to 16

incl.). The HouseCode can also be set on the controllers, so that the

controllers and modules become part of the same system. The address can be

set either using code dials or by pressing buttons, depending on the type of

module.

The Marmitek X-10 System uses standard commands, which control all units

with the same HouseCode at the same time (e.g. all lights on, all off, etc.).

Signal Range

Range of Marmitek X-10 signals over the Power Line and how to

increase the range.

The Marmitek X-10 System is based on power line communication. The

range of the Marmitek X-10 signals very much depends on the local

circumstances. On average the range is a cable length of 80 meters.

If you have difficulties with the range of your Marmitek X-10

signals, please pay attention to the following facts:

1. When more than one phase is used for your electrical system, it is

necessary to couple these phases for the Marmitek X-10 signals.

For coupling you can use FD10 Phase Couplers/Filters. You only need to

install a Phase Coupler/Filter when your wall outlets and light switches are

divided over more than one phase (more than one group is no problem).

For bigger buildings or longer distances we advice you to use an active

repeater instead of passive FD10’s.

2. It is possible that Marmitek X-10 signals are attenuated by devices and

lights which are connected to the power line. In a normal home situation

this effect is negligible (the Marmitek X-10 system is using active gain

control to eliminate the effects). However, it is possible that a particular

4©MARMITEK

device in your house is attenuating the signals so much that the range of

Marmitek X-10 signals is decreased significantly. When you have range

problems, it is wise to try to locate the device which is attenuating the

signals simply by unplugging devices from the power line, and testing the

differences in range for your Marmitek system. When e.g. your conclusion

is that e.g. your computer monitor is attenuating the signal, you can use a

FM10 Plug-in Filter between the power line and the monitor to eliminate

the effects.

Known devices which can cause attenuation are:

PC Monitors

PCs with heavy internal power supplies

Old Televisions

Copiers

Fluorescent Lights

Gas Discharge Lamps (Energy Saving Lamps)

3. Some (old) devices are able to disturb the signal by transmitting noise on

the power line. Because the Marmitek X-10 signals are transmitted on 120

kHz, only noise on or near this frequency will have influence on the range.

When you use a FM10 Filter to connect this device to the power line, the

noise will be filtered.

4. The Marmitek X-10 protocol has several mechanism to avoid modules to

be switched on or off by other sources than your Marmitek X-10 Controllers.

However, it is possible that the Marmitek X-10 signals are disturbed by e.g.

baby phones which are in TALK mode (continuous transmission). When

these kind of signals are present on the power line it is possible that the

Marmitek X-10 signals will not come through.

5. The mains do not stop at the front door of your home. Everything that is

attached to mains nearby your home can have influence on Marmitek X-10

signals (e.g. heavy machinery). If you think that your system is influenced by

devices out of your house, it is advisable to install FD10 Phase Coupler/Filter

on each phase entering the house. These filters will block signals coming

into or going out of your house, but will also match the impedance for the

mains. The FD10’s will not only filter but will also couple the phases (please

see 1).

5SS13TM

ENGLISH

INSTRUCTIONS FOR USE SS13™

WIRELESS SWITCH

INTRODUCTION

Congratulations buying the Marmitek X-10 SS13 wireless switch. This is a

super thin, elegant wireless switch. It is the ideal solution for situations

where an extra switch is needed without installing wires. It is to install on

walls, glass, doors tables etc. and transmits high frequent signals through

walls and ceilings. The SS13 wireless switch transmits radio graphical signals

to an X-10 Transceiver TM13, IRRF7243 or Marmitek X-10 Alarm station.

Then the Transceiver or Station transmits these signals via the in your house

already installed electric wiring. Through this you can switch on and off

your lighting (or apparatus) connected to X-10 receivers (lighting can be

dimmed also). The SS13 is completely wireless and battery powered.

PROPERTIES

The switches are delivered standard at HouseCode A. The top button serves

UnitCode 1, the next one 2, and the 3rd button UnitCode 3. The bottom

button is the dim button. The dim button works for the last activated

UnitCode.

Change of the HouseCode

1. Press the top button ON and keep it pressed. The red LED flashes shortly.

After 3 seconds the present set-up is shown: 1 flash is HouseCode A, 2

flashes is HouseCode B etc.

2. Release the top button ON.

3. Now press shortly for the desired HouseCode on the same top ON

button (1x = A, 2x = B etc). The LED flashes every time you press the

button.

4. At the last time keep the button pressed. After 3 seconds the LED shows

the set-up HouseCode. Now release the button.

Change of the UnitCode

When setting up the UnitCode the top button is set up in the desired

UnitCode. The next buttons are always automatically one UnitCode higher

than the button directly above it ( for instance, when you set up the first

button to UnitCode 6 then the next button is automatically UnitCode 7

6©MARMITEK

and the next on 8).

1. Press the top OFF button and keep it pressed. The red LED flashes

shortly. After 3 seconds the present set up is shown: 1 flash is UnitCode

1, 2 flashes is UnitCode 2 etc.

2. Release the top OFF button.

3. Now press shortly for the desired UnitCode on the same top OFF button

(1x = 1; 2x = 2 etc.) The Led flashes every time you press the button.

4. At the last time keep the button pressed. After 3 seconds the LED shows

the set-up UnitCode. Now release the button.

Change of the battery

Open the sliding drawer at the back of the switch and replace the battery.

Use an identical 3V lithium battery (type CR2032). Mind the polarity when

replacing.

APPLICATIONS

With the Marmitek X-10 SS13 wireless switch in combination with the

TM13 you can activate pre-programmed macros in the CM11 computer

interface.

You can also use the SS13 as a central operation panel for your Marmitek

installation (max. 3 unique UnitCodes.).

FREQENTLY ASKED QUESTIONS

What is the reason for modules to switch on/off spontaneously?

It is possible that a Marmitek X-10 System is installed at one of your

neighbours using the same HouseCode. To solve this problem try to change

the HouseCode of your system, or have FD10 Phase Coupler/Filter installed

at your incoming mains.

My modules will not respond to my controller.

Make sure that the HouseCode on all Modules and Controllers are set to

the same HouseCode (A .. P).

My modules will not react to my remote / sensor.

When you use a remote or sensor, you should have at least one TM13

Transceiver or Marmitek Security Console installed in your house. These

components will translate the radio signals to the Marmitek X-10 signal on

7SS13TM

ENGLISH

the power line. Only one Transceiver should be installed for all remotes and

sensors set to the same House Code.

Am I able to increase the range of my remotes by using more

Transceivers?

Yes, you can use more than one TM13 Transceiver in your home when the

range of your remotes is not sufficient. The TM13 is using so called collision

detection to prevent signals to be disturbed when more than one TM13 is

transmitting. TM13’s will wait for a quite power line before transmitting

their data. To prevent your Marmitek X-10 System to become slow or to

prevent dimming from becoming less smooth, make sure that the TM13

units are placed as far away from each other as possible.

The other modules do not respond to signals of the SS13. What can

be the problem?

• Check if the SS13 has been set-up correctly. The easiest way to do this

is to give again the correct HouseCode to the top button.

• Has the battery been placed correctly?

• The SS13 uses a Transceiver module (TM13, IRRF7243 or one of the

Marmitek X-10 alarm stations). Check if it works properly, for instance

to use another remote control.

• Maybe the range of the SS13 is not sufficient for your purpose; if so,

when using a TM13, place an extra TM13 in the neighbourhood of

your SS13.

Do you still have questions? Please check out www.marmitek.com

for more information.

8©MARMITEK

TECHNICAL DATA

Supply: 1x CR2032 3V lithium battery (supplied)

RF range: Up to 30m free field, up to 20m through walls and

ceilings

RF frequency: 433,92 MHz

RF power: 1mW

X-10 Key codes: On, off, dim, bright

Ambient temperature: - 10° C to + 50° C (operation)

- 20° C to + 70° C (storage)

Dimensions: 115x70x7mm

9SS13TM

ENGLISH

Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on

the product and/or its packaging must not be disposed of with unsorted municipal

waste. The symbol indicates that this product should be disposed of separately from

regular household waste streams. It is your responsibility to dispose of this and

other electric and electronic equipment via designated collection facilities appointed

by the government or local authorities. Correct disposal and recycling will help prevent potential

negative consequences to the environment and human health. For more detailed information

about the disposal of your old equipment, please contact your local authorities, waste

disposal service, or the shop where you purchased the product.

GEBRAUCHSANLEITUNG

SS13™DRAHTLOSER SCHALTER

SICHERHEITSHINWEISE

• Um Kurzschluss vorzubeugen, dieses Produkt bitte ausschließlich innerhalb des

Hauses und nur in trockenen Räumen nutzen. Setzen Sie die Komponenten

nicht Regen oder Feuchtigkeit aus. Nicht neben oder nahe eines Bades,

Schwimmbades usw. verwenden.

• Setzen Sie die Komponente Ihres Systems nicht extrem hohen Temperaturen

oder starken Lichtquellen aus.

• Das Produkt niemals öffnen: Das Gerät enthält Bestandteile mit

lebensgefährlicher Stromspannung. Überlassen Sie Reparaturen oder Wartung

nur Fachleuten.

• Bei einer zweckwidrigen Verwendung, selbst angebrachten Veränderungen

oder selbst ausgeführten Reparaturen verfallen alle Garantiebestimmungen.

Marmitek übernimmt bei einer falschen Verwendung des Produkts oder bei

einer anderen Verwendung des Produktes als für den vorgesehenen Zweck

keinerlei Produkthaftung. Marmitek übernimmt für Folgeschäden keine andere

Haftung als die gesetzliche Produkthaftung.

• Dieses Produkt ist kein Spielzeug. Außer Reichweite von Kindern halten.

• Batterien: Halten Sie die Batterien außerhalb der Reichweite von Kindern.

Liefern Sie die Batterien als chemischen Kleinabfall ein. Verwenden Sie niemals

alte und neue oder unterschiedliche Typen von Batterien durcheinander. Wenn

Sie das System längere Zeit nicht benutzen, entfernen Sie die Batterien.

Achten Sie beim Einlegen der Batterien auf die Polarität (+ / -): Ein falsches

Einlegen kann zu Explosionsgefahr führen.

• Automatisches Schalten ist nicht nur bequem, sondern kann auch Gefahr

bedeuten. So können Personen überrascht werden, oder kann Kleidung, die

über eine elektrische Wärmequelle hängt in Brand geraten. Passen Sie immer

auf und treffen Sie Maßnahmen um dies zu verhindern.

WIE FUNKTIONIERT MARMITEK X-10?

Die Komponenten aus dem Marmitek X-10 Sortiment kommunizieren mit

einander über das bestehende Lichtnetz (mittels Marmitek X-10 Signalen).

10 © MARMITEK

Inhaltsverzeichnis

Sprachen:

Andere Marmitek Schalten Handbücher

Marmitek

Marmitek CONNECT 421 Bedienungsanleitung

Marmitek

Marmitek SMM31 Bedienungsanleitung

Marmitek

Marmitek Connect TS21 Bedienungsanleitung

Marmitek

Marmitek SPEAKER ANYWHERE 350 Bedienungsanleitung

Marmitek

Marmitek Connect 310 UHD 2.0 Bedienungsanleitung

Marmitek

Marmitek Connect 642 Pro Bedienungsanleitung

Marmitek

Marmitek Connect 621 UHD 2.0 Bedienungsanleitung

Marmitek

Marmitek SW10 Bedienungsanleitung

Marmitek

Marmitek Connect TS41 Bedienungsanleitung

Marmitek

Marmitek Connect 421 UHD Bedienungsanleitung

Marmitek

Marmitek Connect 540 UHD Bedienungsanleitung

Marmitek

Marmitek Connect 350 UHD 2.0 Bedienungsanleitung

Marmitek

Marmitek CONNECT 236 Bedienungsanleitung

Marmitek

Marmitek AD10 Bedienungsanleitung

Marmitek

Marmitek Connect 310 Bedienungsanleitung

Marmitek

Marmitek Connect 620 UHD 2.0 Bedienungsanleitung

Marmitek

Marmitek Connect TS41 Bedienungsanleitung

Marmitek

Marmitek Connect 720 Bedienungsanleitung

Marmitek

Marmitek Connect 620 UHD 2 Bedienungsanleitung

Marmitek

Marmitek Connect 310 Gebrauchsanweisung

Marmitek

Marmitek SPEAKER ANYWHERE 350 Bedienungsanleitung

Marmitek

Marmitek Connect TS21 Bedienungsanleitung

Marmitek

Marmitek X10 SS12E Bedienungsanleitung

Marmitek

Marmitek SW12 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung