Marmitek Home Control TM13 Bedienungsanleitung

20151/20120329 • TM13™ TRANCEIVER MODULE

TM13™

TRANCEIVER MODULE

USER MANUAL 3

GEBRAUCHSANLEITUNG 9

GUIDE UTILISATEUR 15

MODO DE EMPLEO 21

MANUALE D’ISTRUZIONI 27

GEBRUIKSAANWIJZING 33

2 © MARMITEK

SAFETY WARNINGS

• To prevent short circuits, this product should only be used inside and only in dry

spaces. Do not expose the components to rain or moisture. Do not use the product

close to a bath, swimming pool etc.

• Do not expose the components of your systems to extremely high temperatures or

bright light sources.

• Do not open the product: the device contains live parts. The product should only

be repaired or serviced by a qualified repairman.

• In case of improper usage or if you have opened, altered and repaired the product

yourself, all guarantees expire. Marmitek does not accept responsibility in the case

of improper usage of the product or when the product is used for purposes other

than specified. Marmitek does not accept responsibility for additional damage other

than covered by the legal product responsibility.

• This product is not a toy. Keep out of reach of children.

• Adapters: Only connect the adapter to the mains after checking whether the mains

voltage is the same as the values on the identification tags. Never connect an adap-

ter or power cord when it is damaged. In that case, contact your supplier.

• Automatic switching devices provide comfort, but can also be dangerous. They can

surprise people or can ignite clothing hanging over an electric heat source. Please be

careful and take appropriate measures to avoid accidents.

TABLE OF CONTENTS

HOW DOES MARMITEK X-10 WORK? 3

INSTRUCTIONS FOR USE TM13 6

INTRODUCTION 6

FIRST USE OF THE TM13 7

FREQENTLY ASKED QUESTIONS 7

TECHNICAL SPECIFICATIONS 8

3TM13™ TRANCEIVER MODULE

ENGLISH

HOW DOES MARMITEK X-10 WORK?

Marmitek X-10 components use the existing mains wiring to communicate (using

Marmitek X-10 signals). You can build a complete system using the three different kind

of components of the Marmitek X-10 System:

1. Modules: These components will receive Marmitek X-10 signals and will

switch or dim the attached lamp or appliance.

2. Controllers: These components will transmit Marmitek X-10 signals and thus

will control the Modules.

3. Transmitters: Wireless components like remotes. The signals of these

components will be received by a controller with transceiver

functionality (IRRF 7243, TM13 or console of a Marmitek Security

System). The Transceiver will translate the signals into Marmitek

X-10 signals on the power line.

ADDRESSES

Up to a maximum of 256 different addresses can be preset. These are subdivided into

a so-called HouseCode (A to P incl.) and a UnitCode (1 to 16 incl.). The HouseCode can

also be set on the controllers, so that the controllers and modules become part of the

same system. The address can be set either using code dials or by pressing buttons,

depending on the type of module.

The Marmitek X-10 System uses standard commands, which control all units with the

same HouseCode at the same time (e.g. all lights on, all off, etc.).

SIGNAL RANGE

Range of Marmitek X-10 signals over the Power Line and how to increase

the range.

The Marmitek X-10 System is based on power line communication. The range of the

Marmitek X-10 signals very much depends on the local circumstances. On average

the range is a cable length of 80 meters.

If you have difficulties with the range of your Marmitek X-10 signals,

please pay attention to the following facts:

1. When more than one phase is used for your electrical system, it is necessary to cou-

ple these phases for the Marmitek X-10 signals. For coupling you can use FD10

Phase Couplers/Filters. You only need to install a Phase Coupler/Filter when your wall

outlets and light switches are divided over more than one phase (more than one

group is no problem). For bigger buildings or longer distances we advice you to use

an active repeater instead of passive FD10’s.

4 © MARMITEK

2. It is possible that Marmitek X-10 signals are attenuated by devices and lights which

are connected to the power line. In a normal home situation this effect is negligible

(the Marmitek X-10 system is using active gain control to eliminate the effects).

However, it is possible that a particular device in your house is attenuating the sig-

nals so much that the range of Marmitek X-10 signals is decreased significantly.

When you have range problems, it is wise to try to locate the device which is atte-

nuating the signals simply by unplugging devices from the power line, and testing

the differences in range for your Marmitek system. When e.g. your conclusion is that

e.g. your computer monitor is attenuating the signal, you can use a FM10 Plug-in

Filter between the power line and the monitor to eliminate the effects.

Known devices which can cause attenuation are:

PC Monitors

PCs with heavy internal power supplies

Old Televisions

Copiers

Fluorescent Lights

Gas Discharge Lamps (Energy Saving Lamps)

3. Some (old) devices are able to disturb the signal by transmitting noise on the power

line. Because the Marmitek X-10 signals are transmitted on 120 kHz, only noise on

or near this frequency will have influence on the range. When you use a FM10 Filter

to connect this device to the power line, the noise will be filtered.

4. The Marmitek X-10 protocol has several mechanism to avoid modules to be swit-

ched on or off by other sources than your Marmitek X-10 Controllers. However, it is

possible that the Marmitek X-10 signals are disturbed by e.g. baby phones which are

in TALK mode (continuous transmission). When these kind of signals are present on

the power line it is possible that the Marmitek X-10 signals will not come through.

5. The mains do not stop at the front door of your home. Everything that is attached

to mains nearby your home can have influence on Marmitek X-10 signals (e.g. heavy

machinery). If you think that your system is influenced by devices out of your house,

it is advisable to install FD10 Phase Coupler/Filter on each phase entering the house.

These filters will block signals coming into or going out of your house, but will also

match the impedance for the mains. The FD10’s will not only filter but will also cou-

ple the phases (please see 1).

5TM13™ TRANCEIVER MODULE

ENGLISH

INSTRUCTIONS FOR USE TM13

INTRODUCTION

Congratulations with your purchase of the Marmitek X-10 HOME CONTROL TM13

Transceiver. Among other things, the TM13 Transceiver allows you to use your Marmitek

X-10 remote control to operate your X-10 switching and dimming modules, wherever

you are in your house.

How does it work?

The TM13 is a controller that is activated by transmitters. The controller operates

Marmitek X-10 modules via the mains to switch your lighting and appliances on and off.

This means that the TM13 forms the heart of your Marmitek X-10 installation.

The TM13 Transceiver operates with the following transmitters:

• Marmitek X-10 remote controls such as the EasyControl8 and the EasyTouch 35.

• The SS13 slimline wireless switch (the ideal solution for situations that require an

(additional) switch without having to fit wires. Can be fitted to walls, glass, doors,

tables, etc.)

• The KR22 wireless remote control (an attractive extra-slim remote control for opera-

tion of Marmitek X-10 Modules from a distance. Can be used as a key ring. Can be

used to control three addresses + dimmer function.)

• The MS13 wireless motion sensor with memory (switches lighting and appliances on

when someone is present and switches them off again afterwards. Switches on

interior and exterior lighting when arriving home in the dark.)

6 © MARMITEK

FIRST USE OF THE TM13

1. Set the HouseCode (A to P) of the Home Control TM13 Transceiver to the same code

as you have set your other modules. The UnitCode cannot be set and will always be

‘1’. If the TM13 is set to HouseCode ‘P’, all commands from remote controls will be

converted into an X-10 signal over the mains, regardless of the HouseCode. The

HouseCode used will in this case be the same as the HouseCode of the remote con-

trol.

2. Point the antenna upwards.

3. Plug the Home Control TM13 into a socket (preferably in a central location of your

house).

4. Insert the plug of an appliance or light in the module. This can now be controlled

using the ‘1’ button of your remote.

Normally speaking, only one TM13 will be required per installation if wireless controllers

are used that are set to the same HouseCode (Does not apply to TM13EFL). The TM13

includes a so-called ‘collision detection’ system. This prevents problems from occurring

when several TM13 modules are used and it allows expansion of the RF range by using

several TM13 modules that are set to one and the same HouseCode.

The module responds to the following Marmitek X-10 commands: ‘ON’, ‘OFF’ and the

Marmitek X-10 group command ‘All Units Off’.

FREQENTLY ASKED QUESTIONS

What is the reason for modules to switch on/off spontaneously?

It is possible that a Marmitek X-10 System is installed at one of your neighbours using

the same House Code. To solve this problem try to change the House Code of your sys-

tem, or have FD10 Phase Coupler/Filter installed at your incoming mains.

My modules will not respond to my controller.

Make sure that the House Code on all Modules and Controllers are set to the same

House Code (A .. P).

Am I able to increase the range of my remotes by using more Transceivers?

Yes, you can use more than one TM13 Transceiver in your home when the range of your

remotes is not sufficient. The TM13 is using so called collision detection to prevent sig-

nals to be disturbed when more than one TM13 is transmitting. TM13’s will wait for a

quite power line before transmitting their data. To prevent your Marmitek X-10 System

to become slow or to prevent dimming from becoming less smooth, make sure that the

TM13 units are placed as far away from each other as possible.

7TM13™ TRANCEIVER MODULE

ENGLISH

Do you still have questions?

Please check out www.marmitek.com for more information.

TECHNICAL SPECIFICATIONS

Supply voltage: 230 V – 50 Hz

Power consumption: < 20 mA, capacitive

Switching capacity: 300W/230V for light bulbs and low-voltage halogen lamps

with a 500W/230V transformer for inductive / capacitive

loads 1200 W/230V for linear loads

Frequency: 433.92 MHz

Transmission signal: 120 kHz ± 2 kHz / 2.5 Vpk-pk

Signal sensitivity: 15 mVpp min, 50 mVpp max at

120 kHz

X-10 Key codes: All Units Off, On, Off, Status Request

Input impedance: 180 ohms (P–N) at 120 kHz

Ambient temperature: –10°C to +50°C (operation),

–20°C to +70°C (storage)

Dimensions: 52 x 122 x 33 mm (excluding plug)

Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product

and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates

that this product should be disposed of separately from regular household waste streams. It is your

responsibility to dispose of this and other electric and electronic equipment via designated collection

facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent poten-

tial negative consequences to the environment and human health. For more detailed information about the dis-

posal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you

purchased the product.

8 © MARMITEK

SICHERHEITSHINWEISE

• Um Kurzschluss vorzubeugen, dieses Produkt bitte ausschließlich innerhalb des

Hauses und nur in trockenen Räumen nutzen. Setzen Sie die Komponenten nicht

Regen oder Feuchtigkeit aus. Nicht neben oder nahe eines Bades,Schwimmbades

usw. verwenden.

• Setzen Sie die Komponente Ihres Systems nicht extrem hohen Temperaturen oder

starken Lichtquellen aus.

• Das Produkt niemals öffnen: Das Gerät enthält Bestandteile mit lebensgefährlicher

Stromspannung. Überlassen Sie Reparaturen oder Wartung nur Fachleuten.

• Bei einer zweckwidrigen Verwendung, selbst angebrachten Veränderungen oder

selbst ausgeführten Reparaturen verfallen alle Garantiebestimmungen. Marmitek

übernimmt bei einer falschen Verwendung des Produkts oder bei einer anderen

Verwendung des Produktes als für den vorgesehenen Zweck keinerlei

Produkthaftung. Marmitek übernimmt für Folgeschäden keine andere Haftung als

die gesetzliche Produkthaftung.

• Dieses Produkt ist kein Spielzeug. Außer Reichweite von Kindern halten.

• Netzadapter: Schließen Sie den Netzadapter erst dann an das Stromnetz an, nach-

dem Sie überprüft haben, ob die Netzspannung mit dem auf dem Typenschild

angegeben Wert übereinstimmt. Schließen Sie niemals einen Netzadapter oder ein

Netzkabel niemals an, wenn diese beschädigt sind. In diesem Fall nehmen Sie

Kontakt mit Ihrem Lieferanten auf.

• Automatisches Schalten ist nicht nur bequem, sondern kann auch Gefahr bedeu-

ten. So können Personen überrascht werden, oder kann Kleidung, die über eine

elektrische Wärmequelle hängt in Brand geraten. Passen Sie immer auf und treffen

Sie Maßnahmen um dies zu verhindern.

INHALTSVERZEICHNIS

WIE FUNKTIONIERT MARMITEK X-10? 10

GEBRAUCHSANLEITUNG TM13 12

EINFÜHRUNG 12

INGEBRAUCHNAHME DES TM13 13

HÄUFIG GESTELLTE FRAGEN 13

TECHNISCHE DATEN 14

9TM13™ TRANCEIVER MODULE

DEUTSCH

WIE FUNKTIONIERT MARMITEK X-10?

Die Komponenten aus dem Marmitek X-10 Sortiment kommunizieren mit einander über

das bestehende Lichtnetz (mittels Marmitek

X-10 Signalen). Das Sortiment besteht aus drei Teilen:

1. Module: Diese empfangen die Marmitek X-10 Signale und schalten oder dim-

men die angeschlossene Belastung.

2. Empfänger: Diese senden die Marmitek X-10 Signale und steuern somit die

Module.

3. Sender: Dies sind drahtlose Komponenten wie z.B. Fernbedienungen. Die

Signale der Sender werden von einem Empfänger mit Transceiver-

funktion (IRRF 7243, TM13 oder die Zentrale eines Marmitek

Alarmsystems) empfangen. Die Signale werden von dem Transceiver

auf das Lichtnetz gesetzt.

ADRESSIERUNG

Sie können maximal bis zu 256 verschiedene Adressen einstellen. Diese sind aufgeglie-

dert in einen so genannten HausCode (A bis einschl. P) und einen UnitCode (1 bis

einschl. 16). Der HausCode kann auch an den Reglern eingestellt werden, sodass Regler

und Module zum selben System gehören werden. Die Adresse kann mithilfe von

Kodierscheiben oder durch Tastenbedienung eingestellt werden. Dies hängt vom

Modultyp ab.

Das Marmitek X-10 System beinhaltet standardmäßige Befehle, wobei alle Units inner-

halb desselben HausCodes zugleich gesteuert werden (z.B. sämtliche Lampen einschal-

ten, alles ausschalten usw.).

REICHWEITE VON SIGNALEN

Reichweite von Marmitek X-10 Signalen über das Lichtnetz und diese

Reichweite vergrössern.

Das Marmitek X-10 System basiert auf der Kommunikation über das bestehende

Lichtnetz. Die Reichweite von Signalen über das Lichtnetz ist sehr von der örtlichen

Situation abhängig. Ein guter Durchschnitt der Reichweite ist jedoch eine Kabellänge

von 80 Metern.

Bei Problemen mit der Reichweite von Marmitek X-10 Signalen sind folgende

Faktoren wichtig:

Werden mehrere Phasen im Haus verwendet, kann es notwendig sein, um diese Phasen

für Marmitek X-10 Signale zu koppeln. Dieses Koppeln kann geschehen, indem Sie

einen FD10 Phasekoppler verwenden und wird benötigt, wenn Steckdosen und

10 © MARMITEK

Andere Handbücher für Home Control TM13

Inhaltsverzeichnis

Sprachen:

Andere Marmitek Transceiver Handbücher

Marmitek

Marmitek Home Control TM13 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung