Marq Gesture Spot 300 Bedienungsanleitung

Quickstart Guide English

Introduction

Box Contents

Gesture Spot 300 Quickstart Guide

Power Cable Safety & Warranty Manual

DMX Cable

Important: Visit marqlighting.com to download the complete User Guide.

Support

For the latest information about this product (documentation, technical specifications, system

requirements, compatibility information, etc.) and product registration, visit marqlighting.com.

For additional product support, visit marqlighting.com/support.

Safety Notes

Important: In addition to the notes below, please refer to the included safety & warranty manual for

additional safety information.

•Carry this product by the hanging/mounting bracket or the handles only.

•Use this product indoors only (IP20). To prevent risk of fire or shock, do not expose this product

to rain or moisture.

•Do not use this product for permanent installations.

•Connect this product to grounded and protected circuits only.

•Always disconnect it from its power source before cleaning or replacing this product’s fuse.

Replace the fuse with another of the same type and rating.

•Before connecting the product to a power source, make sure the power cable is not crimped or

damaged.

•Make sure the power outlet’s voltage is within the range stated on this product (on its housing or

decal).

•Never connect this product to a dimmer or rheostat.

•Never disconnect this product from the power cable by pulling or tugging on the cable itself.

•If you mount this product overhead, use a safety cable.

•Always make sure this product is used in a location with adequate ventilation with at least 20”

(50cm) from adjacent surfaces. Make sure none of this product’s ventilation slots are obstructed.

•Do not use this product at ambient temperatures higher than 104 °F / 40 °C.

•Do not allow flammable materials near this product during use.

•Do not look at the light source when the product is on.

•Do not touch this product while it is powered on or immediately after powering it off. The product

and its housing can reach high temperatures.

•If you encounter a serious problem while using this product, stop using it immediately.

•Do not open this product’s housing. It contains no user-serviceable parts and will void your warranty.

Features

Rear Panel

1. Power In: Use a standard power

cable (included) to connect this

input to a power outlet.

2. Fuse: This compartment holds the

fuse. Before cleaning or replacing

the fuse, disconnect Gesture

Spot 300 from its power source.

Use a screwdriver or other tool to

remove the compartment (do not

pull it out by the tab only). Replace

the fuse only with a new fuse with

the same rating (250 V, 4 A).

3. DMX In: Use a standard 3-pin DMX cable to connect this input (A) to your DMX controller or (B)

to another fixture that will pass DMX data through it to this one. Gesture Spot 300 receives DMX

data over this connection. Please see Setup > Linking > DMX for information about linking

multiple fixtures.

4. DMX Out: Use a standard 3-pin DMX cable to connect this output to an additional fixture.

Gesture Spot 300 sends its data to an additional fixture over this connection. Please see Setup >

Linking > DMX for information about linking multiple fixtures.

Front Panel

5. Display: This display shows

messages and values indicating

the fixture’s current status.

6. Menu: Press this button to access

Gesture Spot 300’s menu.

7. Up: Press this button to select the

next-highest menu option or to

increase the value by 1.

8. Down: Press this button to select

the next-lowest menu option or to

decrease the value by 1.

9. Enter: Press this to confirm your current selection or value.

10. DMX: This light will illuminate when Gesture Spot 300 is receiving DMX data properly through its

DMX In.

11. Error: This light will illuminate when Gesture Spot 300 receives an invalid DMX command.

6789

234

Setup

Note: Items not listed under the Introduction > Box Contents are sold separately.

Power Information

Before connecting the fixture to a power outlet, make sure the power cable is not crimped or

damaged. Also, make sure the power outlet’s voltage is within the range stated on this product (on

its housing or decal).

Before cleaning or replacing the fuse, disconnect Gesture Spot 300 from its power source. Use a

screwdriver or other tool to remove the compartment (do not pull it out by the tab only). Replace the

fuse only with a new fuse with the same rating (250 V, 4 A).

Mounting/Rigging

Standing

Place the fixture on a flat, stable surface. Make sure all cables are secured and placed so that no one

will trip over them.

Suspended

345

Clamp (not included)

Hanging Bracket

1/4-turn

Follow these steps to use the

hanging bracket (included) for

mounting the fixture to a truss.

(tighten until

secure)

Linking

When using multiple Gesture Spot 300 fixtures, you can link (“daisy-chain”) them so that each each

fixture sends DMX data to the next one. This helps reduce clutter in your cabling and save you setup

time.

DMX

Use a standard 3-pin DMX cable to connect the DMX Out of one fixture to the DMX In of another.

Your connected DMX controller will send its data to the fixtures in sequence. All fixtures in this chain

will receive all DMX data.

According to the DMX standard, you can link up to 32 fixtures with up to 300 feet (91 meters)

between each fixture, without amplification. Keep in mind the number of channels you are using as

well as the starting address.

Gesture Spot 300 Gesture Spot 300 Gesture Spot 300

DMX Controller

Operation

Menu Options

Menu Submenu Settings/Values Description

DMX

Function

DMX Address 001

–

512 DMX address setting

Channel Mode 13Ch 13-channel operation

7Ch 8-channel operation

No DMX Signal Keep When no DMX signal, do nothing (hold)

Auto When no DMX signal, enter Run Mode

Clear When no DMX signal, black out

DMX Monito

iew values received on DMX channels

Auto

Movement

Run Mode See Description DMX, Sound, Random, 8 auto movement programs

Sound Active On, Of

Sound activation

Sound Sense 000

–

100 Sound-activation microphone sensitivity, low (000)

to high (255)

Slave Mode Slav 1

–

4 4 slave modes

Manual

Test

Pan 000

–

255 Pan angle, 0° (000) to 540° (255)

Pan Fine 000

–

255 Fine control of panning

Tilt 000

–

255 Tilt angle, 0° (000) to 270° (255)

Tilt Fine 000

–

255 Fine control of tilting

Pan/Tilt Time 000

–

255 Pan/tilt speed, fast (000) to slow (255)

Dimme

000

–

255 Dimmer, dark (000) to bright (255)

Stop/Strobe 000

–

255 Shutter (see 13-Channel Operation > Channel 7

)

Colo

000

–

255 Color options (see 13-Channel Operation > Channel 8

)

Gobo Change 000

–

255 Gobo options (see 13-Channel Operation > Channel 9

)

Gobo Rotation 000

–

255 Rotation, slow (000) to fast (255)

Prism Insertion 000

–

255 3-facet prism

Macro Function 000

–

255 Macro functions (see 13-Channel Operation >

Channel 12)

Ctrl Functions 000

–

255 Blackout & reset functions (see 13-Channel Operation

> Channel 13)

Fixture

Settings

Pan Limit 540

, 360

, 180

Select range of pan angle: 540°, 360°, or 180°

Tilt Limit 270

, 180

, 90

Select range of tilt angle: 270°, 180°, or 90°

Invert Pan On, Of

Invert pan direction

Invert Tilt On, Of

Invert tilt direction

Swap Pan-Tilt On, Of

Switch pan and tilt

Pan-Tilt Correction On, Of

Correct pan and tilt

Load Default All OK, Cancel Restore default pan and tilt settings

Menu Options (continued)

Display

Settings

Inverse Invert control panel’s display

Auto-Of

On, Of

Automatically turn off display when not in use

Fixture

Information

Firmware Currently installed firmware version

Total Use Hours Total running time (HHHHH:MM)

Current Use Hours Current use running time (HHHHH:MM)

Offset

Calibration

Pan Calibration -128

–

+127 Offset for pan value

Tilt Calibration -128

–

+127 Offset for tilt value

Color Calibration -128

–

+127 Offset for color value

Gobo Calibration -128

–

+127 Offset for gobo value

Gobo Rot. Calibration -128

–

+127 Offset for gobo rotation value

Prism Insertion -128

–

+127 Offset for prism value

Reset All OK, Cancel Restore all default settings

DMX Functions

You can control Gesture Spot 300 by linking it to a DMX controller. Please see the complete User

Guide at marqlighting.com to learn how to do this. See below for charts of available functions.

13-Channel Operation

Channel Function Value Description

1 Pan 000

–

255 Pan angle, 0° (000) to 540° (255)

2 Pan Fine 000

–

255 Fine control of panning

3 Tilt 000

–

255 Tilt angle, 0° (000) to 270° (255)

4 Tilt Fine 000

–

255 Fine control of tilting

5 Pan/Tilt Speed 000

–

255 Pan/tilt speed, fast (000) to slow (255)

6 Dimme

000

–

255 Dimmer, dark (000) to bright (255)

7 Shutte

000

–

003 Closed

004

–

007 Open

008

–

076 Strobe, slow (008) to fast (076)

077

–

145 Pulse, slow (077) to fast (145)

146

–

215 Random strobe, slow (146) to fast (215)

216

–

255 Open

13-Channel Operation (continued)

Channel Function Value Description

8 Color Wheel 000

–

006 White

007

–

013 Red

014

–

020 Green

021

–

027 Blue

028

–

034 Yellow

035

–

041 Purple

042

–

048 Light Blue

049

–

055 Orange

056

–

063 Pin

064

–

127 Color indexing

128

–

189 Clockwise, fast (128) to slow (189)

190

–

193 Stop

194

–

255 Counterclockwise, slow (194) to fast (255)

9 Gobo Wheel

See Technical Specifications >

Gobos to view gobo patterns.

000

–

007 Open/white

008

–

015 Gobo 1

016

–

023 Gobo 2

024

–

031 Gobo 3

032

–

039 Gobo 4

040

–

047 Gobo 5

048

–

055 Gobo 6

056

–

063 Gobo 7

064

–

071 Open spot shaking, slow (064) to fast (071)

072

–

079 Gobo 1 shaking, slow (072) to fast (079)

080

–

087 Gobo 2 shaking, slow (080) to fast (087)

088

–

095 Gobo 3 shaking, slow (088) to fast (095)

096

–

103 Gobo 4 shaking, slow (096) to fast (103)

104

–

111 Gobo 5 shaking, slow (104) to fast (111)

112

–

119 Gobo 6 shaking, slow (112) to fast (119)

120

–

127 Gobo 7 shaking, slow (120) to fast (127)

128

–

189 Counterclockwise gobo change, fast (128) to slow (189)

190

–

193 Stop at current position

194

–

255 Clockwise gobo change, slow (194) to fast (255)

10 Gobo Rotation 000

–

127 Indexed position, 0° (000) to 360° (127)

128

–

189 Counterclockwise gobo scroll, fast (128) to slow (189)

190

–

193 Stop at current position

194

–

255 Clockwise gobo scroll, slow (194) to fast (255)

11 Prism 000

–

127 No function

128

–

255 Prism effect

13-Channel Operation (continued)

Channel Function Value Description

12 Macro Functions 000

–

007 No function

008

–

023 Automatic movement 1

024

–

039 Automatic movement 2

040

–

055 Automatic movement 3

056

–

071 Automatic movement 4

072

–

087 Automatic movement 5

088

–

103 Automatic movement 6

104

–

119 Automatic movement 7

120

–

135 Automatic movement 8

136

–

151 Sound-active movement 1

152

–

167 Sound-active movement 2

168

–

183 Sound-active movement 3

184

–

199 Sound-active movement 4

200

–

215 Sound-active movement 5

216

–

231 Sound-active movement 6

232

–

247 Sound-active movement 7

248

–

255 Sound-active movement 8

13 Control Functions

All functions are executed

after 2 seconds.

000

–

049 No function

050

–

059 Blackout during pan/tilt or colo/gobo change

060

–

069 Disable blackout during pan/tilt or colo/gobo change

070

–

079 Blackout during pan/tilt

080

–

089 Disable blackout during pan/tilt

090

–

099 Blackout during color change

100

–

109 Disable blackout during color change

110

–

119 Blackout during gobo change

120

–

129 Disable blackout during gobo change

130

–

139 No function

140

–

149 Reset pan/tilt

150

–

169 Reset color/gobo/focus/prism

170

–

199 No function

200

–

209 Reset all

210

–

255 No function

7-Channel Operation

Channel Function Value Description

1 Pan 000–255

Pan angle, 0° (000) to 540° (255)

2 Tilt 000–255

Tilt angle, 0° (000) to 270° (255)

3 Shutter 000–003 Closed

004–007 Open

008–076 Strobe, slow (008) to fast (076)

077–145 Pulse, slow (077) to fast (145)

146–215 Random strobe, slow (146) to fast (215)

216–255 Open

4 Color Wheel 000–006 White

007–013 Red

014–020 Green

021–027 Blue

028–034 Yellow

035–041 Purple

042–048 Light Blue

049–055 Orange

056–063 Pink

064–127 Color indexing

128–189 Clockwise, fast (128) to slow (189)

190–193 Stop

194–255 Counterclockwise , slow (194) to fast (255)

5 Gobo Wheel

See Technical Specifications >

Gobos to view gobo patterns.

000–007 Open/white

008–015 Gobo 1

016–023 Gobo 2

024–031 Gobo 3

032–039 Gobo 4

040–047 Gobo 5

048–055 Gobo 6

056- 063 Gobo 7

064–071 Open spot shaking, slow (064) to fast (071)

072–079 Gobo 1 shaking, slow (072) to fast (079)

080–087 Gobo 2 shaking, slow (080) to fast (087)

088–095 Gobo 3 shaking, slow (088) to fast (095)

096–103 Gobo 4 shaking, slow (096) to fast (103)

104–111 Gobo 5 shaking, slow (104) to fast (111)

112–119 Gobo 6 shaking, slow (112) to fast (119)

120–127 Gobo 7 shaking, slow (120) to fast (127)

128–189 Counterclockwise gobo change, fast (128) to slow (189)

190–193 Stop at current position

194–255 Clockwise gobo change, slow (194) to fast (255)

6 Gobo Rotation 000–127 Indexed position, 0° (000) to 360° (127)

128–189 Counterclockwise gobo scroll, fast (128) to slow (189)

190–193 Stop at current position

194–255 Clockwise gobo scroll, slow (194) to fast (255)

7 Prism 000–127 No function

128–255 Prism effect

Andere Handbücher für Gesture Spot 300

Inhaltsverzeichnis

Andere Marq Scheinwerfer Handbücher

Marq

Marq Gesture Spot 300 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung