Marshall Amplification MS45 Montageanleitung

ROTARY MUCK SPREADERS

OPERATING & SAFETY INSTRUCTIONS

FOR SPARE PARTS GO TO

WWW.MARSHALL-TRAILERS.CO.UK

FOR MODELS:

MS45, MS60, MS75, MS90, MS105

CHARLES J. MARSHALL (ABERDEEN) LTD

CHAPEL WORKS, BUCKSBURN, ABERDEEN, AB21 9TL.

Telephone: 01224 722777 Fax: 01224 724034

Email: [email protected]k

www.marshall-trailers.co.uk

EC DECLARATION OF CONFORMITY

WE: CHARLES J. MARSHALL (ABERDEEN) LTD

CHAPEL WORKS, BUCKSBURN, ABERDEEN, SCOTLAND, AB21 9TL.

DECLARE THAT THE PRODUCT:

MAKE: CHARLES J. MARSHALL (ABERDEEN) LTD

TYPE: MARSHALL ROTARY MUCKSPREADER

MODEL: _______________________________

SERIAL NO: ______________

CONFORMS TO THE ESSENTIAL HEALTH & SAFETY REQUIREMENTS

OF 98/37/EC MACHINERY DIRECTIVE AS AMENDED BY 2006/42/EC

DIRECTIVE.

PLACE OF ISSUE –CHAPEL WORKS, BUCKSBURN,

ABERDEEN, SCOTLAND, AB21 9TL.

NAME & TITLE OF AUTHORISED PERSON:

CHARLES R. MARSHALL

MANAGING DIRECTOR

DATE: ___________

WE ENCLOSE OUR INSTRUCTIONS FOR THE SAFE OPERATION OF

THIS MACHINE, THE WORKING OF WHICH IS FULLY UNDERSTOOD

BY THE UNDERSIGNED.

CUSTOMER’S SIGNATURE: _____________________ DATE: ___________

SAFETY INSTRUCTIONS

Important Safety advice!

1. STOP

2. THINK

3. CALL 01224 722777

Safety First: Please read and fully understand the contents of this

instruction manual, if you are in any doubt whatsoever of the safe

operation of this machine, please contact Charles J. Marshall (Aberdeen)

Ltd on Tel. 01224 722777.

1. Guards - Ensure all guards are securely fastened in place.

2. Maintenance - Ensure the machine and tractor is completely stopped prior to carrying

out any maintenance.

3. PTO Shaft - Safety is important, if you are in any doubt of how to fit the PTO shaft,

please contact our service department.

4. Always apply the parking brake when the Muck Spreader is to be left unhitched

from the tractor.

OPERATING INSTRUCTIONS

YOUR MARSHALL MUCKSPREADER HAS BEEN DESIGNED TO GIVE YOU LONG

AND RELIABLE SERVICE. THIS CAN BE ENSURED BY FOLLOWING THE

INSTRUCTIONS BELOW.

OPERATING

Operating the Muck Spreader –Open the hydraulically operated lid to allow for better access.

It is advisable that you do not cover the starters at either end of the main rotor shaft with solid

type muck as this will significantly increase the time the spreader will take to get started. Once

you have loaded the spreader close the hydraulic lid, if the spreader is over filled this will not

matter, simply place the hydraulic lever in the float position and when the spreader starts it will

continue closing. Start the PTO shaft at low engine revs and increase the speed until you are

satisfied with the spread rate and pattern. As the spreader continues and the flail chains get to

work it will be necessary to either increase the forward speed or decrease the rotor speed to

keep the same spread rate and pattern. When the load is discharged always reduce the engine

revs to idling prior to shutting off the PTO shaft.

1. Always disengage PTO shaft when turning.

2. Never spread with the muck spreader lid in the open position.

3. Always couple the spreader brakes and lights up every time you use the spreader

this reduces the chance of corrosion and the brake mechanism seizing due to

lack of use.

BEFORE USING CHECK THE FOLLOWING:

1. Ensure there is tension in the drive line and that side play does not exceed

20mm.

2. Ensure that all bolts that are not accessible when the guard is in place,

particularly those securing the small drive shaft bearings, are tight.

3. Ensure that the locknuts on the chain tension adjusters are not loose.

4. Lubricate all bearings as necessary –those in the PTO shaft (one grease point in

each knuckle), two on the main rotor shaft bearings and four on the input shaft

bearings.

5. Ensure all nuts and bolts are secure.

6. Check the hydraulic hoses for wear or damage and ensure the couplings are

clean.

7. Check the flails and flail heads for damage.

8. Drain any accumulation of water as necessary as frozen water can cause

damage to the drive line.

MAINTENANCE INSTRUCTIONS

1. Hubs / Bearings must be greased regularly; we recommend they are checked

after the first fourteen days work, then six monthly thereafter.

2. Tyre pressure should be checked regularly (See page 6).

3. Wheel nuts should be checked when the machine is new, then after operating

for one hour, then one day and weekly thereafter. The same procedure applies

if nuts have been removed and replaced.

4. Check the tow hitch for wear and replace accordingly.

5. Lights should be kept clean and if not in use for some length of time, coating

with some form of oil spray is recommended.

BRAKE ADJUSTMENT: Always adjust brakes with the spreader on a completely level

surface.

This can be done by loosening the nut behind the clevis, then rotating the piston,

adjustment will appear from the ram. Remember to tighten the locknut when

completed.

IF THE MUCKSPREADER IS NOT TO BE USED FOR A CONSIDERABLE PERIOD OF

TIME THE FOLLOWING TASKS SHOULD BE CARRIED OUT TO MAINTAIN IT IN

GOOD CONDITION:

1. Remove the drain cover and clean the muck spreader thoroughly with cold water at

a moderate pressure. Do not replace the drain cover until the muck spreader is

ready for use again.

2. Ensure the lid is in the up position before uncoupling the hose.

3. Touch-up any scraped or damaged paintwork.

4. All grease nipples should be greased and the machine run for 15 minutes to work

in the lubricant.

HISTORICAL CHANGES

1. 1976 –Lid ram changed to pulling lid ram.

2. 1996 –Brakes fitted.

3. 1998 –MS/85 used 60mm bearings on input shaft up to 1998.

4. 1999 –Chain tensioning brackets on all models used a bolt on front until 1999.

5. 2001 –Larger lid fitted.

6. 2001 –Lights fitted to MS60, MS70, MS85, MS105/T & MS155/T

7. 2002 –All MS45, MS70, MS85 used splined PTO shafts up to 2002.

Part Number Size Maximum Weight Speed Max Tyre Pressure

083/01-26-12 26 x 1200 x 12 800kg 25km/h 20psi

083/01-100-12 10.0/80x12 10ply 1000kg 30km/h 45psi

083/01-100-15 10.0 x 15.3 1500kg 30km/h 52psi

083/01-115-15 11.5 x 15 2000kg 30km/h 52psi

083/01-125-15 12.5 x 15 2500kg 30km/h 60psi

N/A 15/70 x 18 3200kg 40km/h 75psi

083/01-15-22.5 15 x 22.5 (385/65R 22.5) 4500kg 80km/h 90psi

083/01-401-60 405x60R 22.5 4500kg 80km/h 90psi

083/01-1555-17 15-55 x 17 2120kg 40km/h 52psi

083/01-1670-20 16/70 x 20 3000kg 40km/h 49psi

083/01-165-70 16.5 x 70 x 18 3200kg 40km/h 54psi

N/A 18 x 22.5 5800kg 80km/h 90psi

N/A BN2 340/457-1300 x 18 2600kg 40km/h 60psi

N/A BN3 1300 x 530 x 533 4500kg 40km/h 53psi

N/A BN4 22/70-20 4500kg 40km/h 33psi

083/01-340-65 XP27 Radial 340/65R 18 2650kg 90km/h 72psi

083/01-400-60 400-60 x 22.5 4000kg 40km/h 51psi

083/01-550-45 550-45 x 22.5 4375kg 40km/h 41psi

083/01-560-45 560-45 x 22.5 4575kg 45km/h 58psi

083/01-560-60 560-60 x 22.5 5595kg 50km/h 58psi

083/01-500-60 500-60 x 22.5 5450kg 40km/h 41psi

083/01-550-60 550-60 x 22.5 5300kg 40km/h 44psi

083/01-445-45 445-45 X19.5 4500kg 100km/h 100psi

083/01-335-50 355-50 X22.5 4500kg 80km/h 100psi

083/01-184-30 18.4 x 30 14 pr 3550kg 40km/h 39psi

083/01-184-34 18.4 x 34 14 pr 3650kg 40km/h 36psi

083/01-231-26 23.1 x 26 3950kg 40km/h 36psi

083/01-281-26 28.1 x 26 6100kg 40km/h 33psi

083/01-305-32 30.5 x 32 7100kg 40km/h 39psi

083/01-750-60 750 x 60 x 30.5 8500kg 40km/h 60psi

Please note this chart is for reference only each tyre brand can have different ratings.

MARSHALL PRE-DELIVERY INSPECTION CHECK

Dealer Name:

Customer’s Name:

Contact No:

Address:

Post Code:

Model:

Serial Number:

Check

Completed

Check Tyre Pressure (See chart on page 6)

Tighten Wheel Nuts

(18mm Stud Diameter = 270Nm / 22mm Stud Diameter = 475Nm)

Grease Hubs

Check External Wheel Bearing

(Ensure No Side Movement on Wheels)

Check Drive Chain Tension

Check All Securing Bolts

Check Lights (If applicable)

Check For Damaged Paint and Touch Up If Necessary

Check Brake Rams (Extend and return freely)

Check Lid Rams (Extend and return freely)

Rams and Hydraulic Hoses Checked for Leaks

Ensure Relevant Paperwork Is Completed and Handed to the

Operator

Signed: ______________________________________ Date: _____________

General Overall Condition Satisfactory

To be returned when completed:

Fax –01224 724034

Email –[email protected]

Post –Charles J Marshall (Aberdeen) Ltd

Chapel Works, Bucksburn, Aberdeen, AB21 9TL.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Marshall Amplification Streuer Handbücher

Marshall Amplification

Marshall Amplification MS45 Montageanleitung

Beliebte Streuer Handbücher anderer Marken

PEQUEA

PEQUEA GT-100 Bedienungsanleitung

Herculano

Herculano H2RS9 Bedienungsanleitung

Epoke

Epoke SKE8 Bedienungsanleitung

GEA

GEA EL44 Technisches Datenblatt

Boss Snowplow

Boss Snowplow TGS 800 Bedienungsanleitung

Fisher

Fisher EMERSON 168 Series Bedienungsanleitung

Fisher

Fisher POLY-CASTER 78601 Bedienungsanleitung

TurfEx

TurfEx RS7200 Betriebsanleitung

Ferris

Ferris Pathfinder Series Bedienungsanleitung

Fayat Group

Fayat Group DYNAPAC S100 Fehlerbehebungshandbuch

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Installations- und Betriebshandbuch

EASTMAN

EASTMAN CR 500 Bedienungsanleitung

Nogueira

Nogueira RoyalFlow-600 Bedienungsanleitung

Buyers

Buyers TGS05B Bedienungsanleitung

Magnum

Magnum V-BOX PV Series Beilage

Meyer's

Meyer's VB280 Bedienungsanleitung

SnowEx

SnowEx VX-4210 Bedienungsanleitung

Kramer

Kramer VM-400HDCP Bedienungsanleitung