Martec Flush AC Series Bedienungsanleitung
www.martecaustralia.com.au
FLUSH AC Series Installation Guide
Thanks for choosing our Flush AC Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
MFF133MM 1250mm 3 Blade Ceiling Fan Matt Black
MFF133WS 1250mm 3 Blade Ceiling Fan White Satin
Models Parameters (Fan and LED Light):-
MFF1333MM 1250mm 3 Blade Ceiling Fan Matt Black with 15W Tricolour LED Light
MFF1333WS 1250mm 3 Blade Ceiling Fan White Satin with 15W Tricolour LED Light
Part List:
Qty 1x motor assembly Qty 1x instruction manual Qty 1x screw kit Qty 1x balancing kit
Qty 1x hanging bracket Qty 1x wall control kit Qty 3x blade
How to Assemble
Secure the hanger bracket to ceiling
beam or a suitable piece of timber
inserted between the ceiling beams
using the two long screws supplied
with the package. (See Fg.1)
Remove pre-installed screws from
motor bracket and mounting plate.
Hang fan from mounting plate by
inserting T-shaped bracket into the
slot. (See Fg.2)
Insert and tighten screws and star
washers into the mating holes to
secure the motor housing. (See Fg.6)
Fg.1 Fg.2 Fg.3
Fg.6
Push motor upward and secure
the motor to the mounting plate by
tightening the screws and washers
provided. (See Fg.4)
Fg.4
Position no.1 and n0.2 directly under
and align with no.3.
Rotate the motor housing clockwise
until both screws from the mounting
bracket drop into the slots. (See Fg.5)
Fg.5
Application
Flat Surface / Ceiling Slope Ceiling up to 15° Corrugated Ceiling Apex Ceiling
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
How to Install Blades
NB: Ensure the blades do not get damaged or bent during the installation process while the fan maybe on the ground, this will aect the
performance and balance of the fan and this is NOT covered under warranty.
Align holes on the blades with holes at the bottom of the motor
assembly. Tighten the blade using screws provided. Repeat the
same step until all blades are installed.(See Fg.7)
Fg.7
CCT (Colour Changeable Temperature)
Fg.10
How to Install / Remove the Cover
1. Install light kit to
connecting plate.
2. Plug in light wire
connection and ensure
the protruding ends of the
connectors are dropped
into the narrow ends of
the slots.
To install turn clockwise to
tighten the cover.
To remove turn anti-
clockwise.
Fg.8
To install turn clockwise to
tighten the cover.
To remove turn anti-
clockwise.
Fg.9Model shown with light Model shown fan only
Dimming
The Four Seasons Link fan has a smart 3 step dimming LED light module which doesn’t require a dimmable remote control or a wall
dimmer.
It only requires a normal on/o remote kit (MPREMS) or a normal light wall switch. (Supplied in remote control kit).
Turn the switch on and the light will turn on. Flick the switch on/o within 1 second and the light output will dim down to approx. 50%.
Flick the switch on/o again and the light output will dim down to approximately 15%. The light kit has no memory function, It will turn
on 100% initially.
Choose colour temperature by icking the switch in the
LED (See Fg.10)
C = 5000K cool white
N = 4000K neutral white
W = 3000K warm white
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Instructions and Functions of Transmitter
Setting the code on transmitter
1. Remove battery cover
2. Slide code switches to your
choice of ON/OFF position
3. Install battery (supplied)
Setting code on receiver:-
1. Slide code switches on the
receiver in the same position
set on the transmitter
Installing Receiver Remote Control
NB: Receiver shown fan only
Antenna wire (black wire)
NB: Receiver shown fan and light
Antenna wire (black wire)
Pairing Instructions
• Turn “ON” the power supply and within 30 seconds
• Press and hold the transmitters “FAN ON/OFF” button for 5 seconds and a “beep” will be heard
• Pairing initial step must be performed within 30 seconds of power being turned on
i) ensure the isolation switch or power supply to the rst installed fan is turned o prior to pairing futher fans
ie. pair one fan at a time
ii) ensure isolation switch is kept to the ON position, the isolation switch is not to be used as a light switch as
this will damage and make the remote recevier inoperable
Important Reminders
• Receiver must be correctly installed in the mounting bracket
• When the transmitter cannot control the receiver, please check
i) has sucient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause interference
• Replace battery if getting low as this will aect sensitivity of the transmitter
• Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks
• Support up to 200W lighting power
• Isolation switch MUST be connected in the line
• Dimming switch on the light models is operated by tuning the light ON/OFF button within 1s. Light output will dim in
stages from 24W to 9W to 3W approximately
Receiver
NB: Martec Remotes - MPREMS (as
illustrated on the left), MPLCDS and
MAPP are sold separately.
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Wire Connections
WARNING
• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Fan and light MUST be earthed.
• Bracket MUST be rmly attached to a at solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• The warranty is VOID if product is not installed according to this installation guide.
6* Year Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
240V Supply
1
1
2
2P Plug
4P Plug
2
To the
Fan Light
To AC
Power
NB: Remote Control with or without light
To the Fan Motor
NB: Wall control with light
4P Plug
NB: Wall control without light
4P Plug
4P Plug
4P Plug
Dieses Handbuch passt für folgende Modelle
4
Andere Martec Lüfter Handbücher
Martec
Martec Lifestyle DC Series Bedienungsanleitung
Martec
Martec NEWPORT Series Bedienungsanleitung
Martec
Martec MXFT25S Bedienungsanleitung
Martec
Martec SATURN MXFSS20W Bedienungsanleitung
Martec
Martec Wave MWF133TSR Bedienungsanleitung
Martec
Martec Cruise Series Bedienungsanleitung
Martec
Martec Discovery Series Bedienungsanleitung
Martec
Martec Elite AC Series Bedienungsanleitung
Martec
Martec LINK AC Series Bedienungsanleitung
Martec
Martec DLS1045 Bedienungsanleitung
Martec
Martec Lifestyle series Bedienungsanleitung
Martec
Martec MR0124 Bedienungsanleitung
Martec
Martec Ariel Series Bedienungsanleitung
Martec
Martec AVOCA DC Series Bedienungsanleitung
Martec
Martec MMDC133WOR Bedienungsanleitung
Martec
Martec SATURN Series Bedienungsanleitung
Martec
Martec Scorpion MSF133 Bedienungsanleitung
Martec
Martec SCORPION DC Series Bedienungsanleitung
Martec
Martec Lifestyle series Bedienungsanleitung
Martec
Martec ZODIAC Leitfaden
