Martin M2GO Bedienungsanleitung
PN: 35001513: M2GO-M2PC Replace Dongle Rev. A
M2GO/M2PC™ Controller
Replacing Dongle with the new Dongle type
Symptom
When the M2GO/M2GO dongle has to be replaced with a new dongle type, an adapter PCB is
used.
Solution
Follow these instructions to replace the Dongle.
Tools needed
Torx T-10 screw driver.
Anti-Static Precautions
Important! Static electricity can destroy electronic
components. Follow these ESD precautions to prevent damage
to the product and injury to the user.
Carry out the service at an anti-static workstation.
Wear a grounded anti-static wristband.
Touch a grounded conductor every few minutes to discharge any
static buildup.
Hold components by their edges only. Do not touch the surfaces or
any of the contacts of the PCBs.
www.martin.com •Olof Palmes Allé 18 •DK-8200 Aarhus N • Denmark
Tel. (+45) 8740 0000 •Fax (+45) 8740 0010
Replacing Dongle (the procedure is for M2GO and M2PC)
1. Switch OFF the controller and
disconnect the power cable from
the controller.
2. Remove the front panel:
Use a Torx T-10
Remove 4 screws from the
front side (orange arrows)
Remove 4 screws from the
back side (orange arrows)
Loosen the 2 scews marked
with the blue arrows.
www.martin.com •Olof Palmes Allé 18 •DK-8200 Aarhus N • Denmark
Tel. (+45) 8740 0000 •Fax (+45) 8740 0010
3. Remove the front panel from the
bottom housing, and place it
behind the bottom housing as
shown in the picture.
4. Remove the cable adapter PCB
from the front panel PCB by
pulling it out of its sockets. Don’t
unplug the cabling.
www.martin.com •Olof Palmes Allé 18 •DK-8200 Aarhus N • Denmark
Tel. (+45) 8740 0000 •Fax (+45) 8740 0010
5. Remove the old dongle by
carefully pulling on the black
connector.
Note: some hot glue may hold the dongle
in place. Peel of the hot glue carefully.
6. The new dongle consists out of 2
parts: an adapter PCB and the
dongle.
7. Connect both parts together as
shown in the picture. The
connector of the adapter PCB
must face up, and the serial label
on the dongle must face down.
www.martin.com •Olof Palmes Allé 18 •DK-8200 Aarhus N • Denmark
Tel. (+45) 8740 0000 •Fax (+45) 8740 0010
8. Connect the new dongle
combination on the front panel
PCB like in the picture.
9. Reconnect the cable adapter PCB
10. Put the front panel back on the
bottom housing.
Warning: Make sure that no cables are
pinched between front panel and bottom
housing.
www.martin.com •Olof Palmes Allé 18 •DK-8200 Aarhus N • Denmark
Tel. (+45) 8740 0000 •Fax (+45) 8740 0010
11. Connect power to the console,
connect to a laptop (only M2PC)
and load a showfile.
12. Check the “LIVE” status in the
lower left corner of the screen.
13. Close the controller by putting the
screws back in place.
Andere Handbücher für M2GO
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Martin Controller Handbücher
Martin
Martin Freekie Bedienungsanleitung
Martin
Martin P3-100 Bedienungsanleitung
Martin
Martin M6 Series Bedienungsanleitung
Martin
Martin M2GO HD Bedienungsanleitung
Martin
Martin DMX 8 Zone Bedienungsanleitung
Martin
Martin M6 Series Bedienungsanleitung
Martin
Martin M6 Series Bedienungsanleitung
Martin
Martin DMX Controller 2518 Bedienungsanleitung
Martin
Martin M3776UK Bedienungsanleitung
Martin
Martin Maxxyz Bedienungsanleitung
