Martin U-DS90W Bedienungsanleitung

01/2012 SM

4444 Lawton Street, Detroit, MI, 48208 USA • Tel: 313-895-0700 • Fax: 313-895-0709

Email: [email protected] • www.MartinUniversalDesign.com

Creation Station Table

Assembly Instructions

Video Assembly Instructions:

Go to www.MartinUniversalDesign.com and click on

Assembly Instructions to watch a video for HOW TO

ASSEMBLE the U-DS90W / U-DS90B, Creation Station

Table.

IMPORTANT:

If you have diﬃculty assembling your U-DS90W/U-DS90B

Creative Center or need customer service assistance.

Please call: Martin Universal Design, Inc. Customer service

Hot Line at 1-313-895-0700. If you need additional parts, it

is not necessary to contact your dealer. Our customer ser-

vice rep. will forward them to you immediatly.

01/2012 SM

(4 Pieces) 6x55mm (6 pieces) Washer (4 Pieces)

Upper Base End (2 pieces) Tilt Mechanism (2 Pieces) 6x28mm (8 pieces) Allen Wrench

Lower Base End (2 pieces) Top L-Bracket (2 Pieces) 5x14mm (8 Pieces)

Foot Bar Drawer Support Rods

(4 pieces) 4x12mm (2 Pieces)

Cross Support (4 Pieces) Nuts (4 Pieces)

Top Support

Cross Support

End Caps (2 pieces) 6x65mm (6 pieces)

Pencil Ledge

Footbar Spacers

(2 Pieces) Collars (4 pieces)

: Table Components

: Fasteners and Tools

U-DS90W / U-DS90B

Creation Station Table Parts List

Drawers:

Please see Last Page of assembly

sheet for drawers.

Drawer Supports

24”x40”Top

Page 2

Phillips Head screw driver

NOT INCLUDED

Casters

Wrench (10mm)

Wrench (12mm)

Packaged with Casters

01/2012 SM

Step 1: Lower Base Ends

• Take the lower base end units (Part C ) and line

up next to each other so the welds are on the inside.

• Take 6x65mm bolt (Part T ) and insert it in the

base end from the outside. Once inserted, slide the

footbar spacer (Part N ) onto the the 6x65 mm bolt

(Part T )making sure the curved end is facing the

lower base and the at part is toward the foot bar.

• Spin foot bar (Part D ) onto the 6x65 mm bolt (Part

T ) using the Allen Wrench (Part W ) to hold the

6x65 mm bolt (Part T ) still. Be sure to leave it loose.

• Take opposite lower base end and repeat Step 1-2

with that base end.

• Line up the base end and secure it loosely to the

foot bar (Part D ). using the Allen Wrench (Part W

) and be sure to leave loose for Step 2.

Step 2: Attaching Cross Support

•Locate the 2 vertical holes on the Lower Base Ends

(Part C ) and insert the 6x55mm bolts (Part O )

through these holes.

• Slide on cross support end cap (Part M ) mak-

ing sure curved part faces the lower base end

(Part C ) and at part faces the Cross Sup-

port (Part E ). DO NOT OVER TIGHTEN to

avoid damaging the cross support end caps.

• Line up holes on Cross Support (Part E )

and tighten with the allen wrench (Part W ).

• Place other support cap up to opposite leg, thread

bolts through the holes and tighten to cross support

(Part E )

• Go back and tighten all 6 bolts so they are snug but

again, BE CAREFUL NOT TO OVER TIGHTEN.

Page 3

Fastener parts needed for this step: T= 2 ea., N=2 ea.

Fastener parts needed for this step: O=4 ea. M=2 ea.

01/2012 SM

• The castors (Part L ) are wrapped separately. (2 locking; 2 non-

locking)

• On the bottom of the lower base you will nd four holes one in

each corner.

• Place locking castors (Part L ) in the front (farthest away from

the cross support). This is for ease of use in moving table later.

- Tighten using wrench with hole (Part Y )

• Place the remaining non locking castors (Part L ) in rear

- Tighten using wrench with hole (Part Y )

Step 3: Attaching the Casters

Step 4: Attaching the Collars

• The Collars (Part U ) are in a separate bag.

• Loosen the lower bolt of the collar (Part U )

• Slide the collar (Part U ) on top of the lower base

(Part C ) making sure the knobs face in so they do not

affect the drawers on the outside.

• Tighten the lower bolt with the Allen wrench (Part W )

- SNUG ONLY, DO NOT OVER TIGHTEN

• Place lower assembly off to side for now.

Step 5: Attaching Upper Base Ends

• Take one upper base end (Part B ).

- 4 Holes face towards inside.

• Place the 6X55mm bolt (Part O ) in the hole

from the outside

• Line up with Top Support (Part F ) and tighten

with Allen Wrench (Part W )

• Repeat with other side

Page 4

Fastener parts needed for this step: O=2 ea.

01/2012 SM

Step 6: Base Assembly

• Take upper assembly and line up the four

posts with the collars. Push the four posts all

the way into the lower assembly. Failure to do

so will make attaching the top (Step 9) difcult.

• Tighten knob to make snug. DO NOT OVER TIGHT-

EN.

Step 7: Drawer Support

• Take 6X65mm bolt (Part T ) and insert through

the inside of the upper base end (Part B )

• Slide on Washer (Part V )

• Slide on [1/ea] Drawer Support (Part H )

• Spin on Drawer Support Rod (Part K )

• From the outside of the base, secure with a

6X28mm Bolt (Part P )

• Repeat this process 3 more times till you have

all 4 drawer supports hanging (two on each upper

base end).

V T

Page 5

Fastener parts needed for this step: P= 4 ea., T= 4 ea., V= 4 ea.

01/2012 SM

Step 8: Tilt Mechanisms

• Carefully place Top (Part A ) upside down on car-

peted area or empty carton to avoid scratching top

surface.

• Locate the end of the table that has the predrilled

holes on the edge. These holes represent the front of

the table top.

• Line up the tilt mechanisms (Part I ) on the holes

closest to the back of the table. Place the wider side

on the table top and line up the holes making sure

the stamped part of the tilt mech is facing outwards. It

should also be extending away from you (toward the

back of the top) if you are sitting at the front of table.

• Now secure with the screws 5x14 mm screws (Part

Q ) using a Phillips head screwdriver (not included).

• Repeat this process with the other tilt mech.

Step 9: Attaching Table Top

• Carefully turn over base and rest it on the tabletop so

the entire table is upside down.

• Place the Top L Brackets (Part J ) in the empty

holes on the front of the upper base end (Part B )

• Line the Top L Brackets (Part J ) up with the two pre

drilled holes closest to the front of the table.

• Using your Phillips head screw driver, secure the Top

L Brackets (Part J ) with 5x14 mm screws (Part Q ).

• Repeat with the other side.

Front

Page 6

Fastener parts needed for this step: Q= 4 ea.

01/2012 SM

Step 10: Attaching Tilt Mechanism to Base

1. Carefully ip the entire table to its upright position, then

raise the tilt mechanisms so the narrow tabs rest on the top

support (Part F ) [[Please See Picture]]

2. Insert the 6x28mm bolts (Part P ) and from the bottom,

secure with the nuts (Part S ) using both the wrench (Part

X ) and Allen Wrench (Part W ).

3. Repeat these steps until all four holes are secured.

Step 11: Pencil Ledge

1. Carefully turn table over so it is standing

right side up.

2. Locate the predrilled holes on the edge of

the front of the table top (Part A )

3. Make sure lip of pencil ledge (Part G ) is

up and adjust the pencil ledge to the desired

position using the shaped holes on the pen-

cil ledge.

• Secure with [2] 4x12 mm screws (Part R )

using your Phillips head screw driver.

Front

Page 7

Fastener parts needed for this step: S= 4 ea., P= 4 ea.

Fastener parts needed for this step: R= 2 ea.

01/2012 SM

HEIGHT ADJUSTMENT:

To adjust the height of your table - loosen the knobs on the collars found on the base of the table and

lift the table top to your desired height.

(To avoid damaging the table top, DO NOT attempt to lower the table top by forcefully pushing down

on the top when its in a locked position.)

TILT ADJUSTMENT:

To adjust the tilt of your table top, grab the back edge of the table top and lift the top with [2] hands to

the maximum tilt and then back down to your desired position. NOTE: You must lift the table top all the

way up before lowering it to the desired tilt level.

NOTE: If the top does not seem to move smoothly - this means you are NOT holding the top balanced

with both hands. Make sure your hands are positioned evenly. This will make the adjustments easier.

In order to lower the table top, life it all the way up to its maximum height which allows the tilt mechanisms to

release from their locked position. To avoid damaging the table top, DO NOT attempt to lower the table top by

forcefully pushing down on the top when its in a locked position.

Adjustments

4444 Lawton Street, Detroit, MI, 48208 USA • Tel: 313-895-0700 • Fax: 313-895-0709

Email: [email protected] • www.MartinUniversalDesign.com

Page 8

01/2012 SM

Assemble your drawers by taking the section [A] and snapping

into place - by lining up the tabs with the grooves in the out-

side edge of section piece [B].

Complete by snapping section [C] onto section A&B.

Finish by sliding the [3] Clear Drawers (Part D) into the drawer

bank assembly.

After proper assembly the drawers should

look like the above illustration.

WARNING: Read all instructions ﬁrst before assembling drawers. Once pieces are snapped together they are secured.

Drawer Assembly Instructions

IMPORTANT:

If you have diﬃculty assembling your U-DS90W/U-DS90B Creative Center or need customer service assistance.

Please call: Martin Universal Design, Inc. Customer service Hot Line at 1-313-895-0700. If you need additional

parts, it is not necessary to contact your dealer. Our customer service rep. will forward them to you immediatly.

4444 Lawton Street, Detroit, MI, 48208 USA • Tel: 313-895-0700 • Fax: 313-895-0709

Email: [email protected] • www.MartinUniversalDesign.com

Top Middle Bottom Clear Drawer

Page 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Martin Inneneinrichtung Handbücher

Martin

Martin GRANDEUR 91-02606115 Betriebsanleitung

Martin

Martin FENG SHUI 91-7706 Bedienungsanleitung

Martin

Martin U-DS92ST Bedienungsanleitung

Martin

Martin 384EB Bedienungsanleitung

Martin

Martin U-DS1922W Bedienungsanleitung

Martin

Martin U-DS31W Bedienungsanleitung

Martin

Martin Comfort Mesh 91-02406115 Bedienungsanleitung

Martin

Martin INDIGO Bedienungsanleitung

Martin

Martin U-DS40 Bedienungsanleitung

Martin

Martin Avanti U-7100 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung