Martin Mania SCX500 Bedienungsanleitung

Mania SCX500

user manual

364

178

442

138

200

DIMENSIONS

All dimensions are in millimeters

reproduced, in any form or by any means, without

permission in writing from Martin Professional A/S,

Denmark.

P/N 35000157, Rev. C

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mania SCX500 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Rigging the Mania SCX500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Focus adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Creating a data link for DMX and master/slave operation . . . . . . . . . . 12

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Auto trig operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Music trig operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Master/slave operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

DMX controller operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Inverting pan and tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Service and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Replacing the main fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Firmware /hard boot uploads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Mania SCX 500 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Introduction 5

1. I

NTRODUCTION

Thank you for selecting the Martin Mania SCX500. This automated

moving-mirror projector has the following features:

• Automatic triggering and music triggering modes

• Stand-alone single fixture and master/slave operation, both with auto

trig and music trig

• DMX controllable, choice of 6- or 8-channel DMX control modes

• 12 pre-programmed macros

• 15 full colors (including white) and 5 multi-colors. Split color feature for

added color capability

• 16 gobos

• 180° pan and 72° tilt

• Adjustable focus

• 15° beam angle

• 150 watt long-life halogen lamp

• Versatile mounting options

Unpacking

The packing material is carefully designed to protect the fixture during

shipment - always use it to transport the fixture.

The Mania SCX500 is supplied with:

• Lamp (installed)

• Power cable

• 5 meter (16.4 ft.) RS-485 XLR cable for data link

• User manual

• Mounting U-bracket and mounting plate

• Fasteners for U-bracket and mounting plate

Important! The mounting plate is attached to the fixture with thumb

screws to protect the mirror, and the mirror assembly is

secured for transport. Before applying power, remove the

mounting plate, remove any transport packaging, and cut and

remove any plastic tie-wraps holding the mirror!

6 Mania SCX500 user manual

Mania SCX500 overview

DMX out

DMX in

Music trig sensitivity

adjustment knob

Power on/off switch

Power input

Main fuse

Settings control panel

Swivel lock

X100 X10 X1 Mode

DMX Address

Settings control panel

Power indicator

Data indicator (DMX / slave

data received)

Mode toggle switch

Introduction 7

Safety information

Warning! This product is for professional use only. It is not for

household use.

This product presents risks of lethal or severe injury due to fire and heat,

electric shock, ultraviolet radiation, lamp explosion, and falls. Read this

manual before installing or powering the fixture, follow the safety

precautions listed below and observe all warnings in this manual and on

the fixture. If you have any questions about how to operate the fixture

safely, please contact your Martin dealer or call the Martin 24-hour service

hotline.

Protecting yourself and others from electric shock

and injury

• Disconnect the fixture from AC power before removing or installing the

lamp, fuse, or any part, and when not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and

electrical codes and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer all service not described in this manual to a Martin service

technician.

• Never operate the fixture with missing or damaged lenses.

• Glass lenses must be changed if they have become visibly damaged to

such an extent that their effectiveness is impaired, for example by

cracks or deep scratches.

• Never operate the fixture with open, missing or damaged covers.

• Protect your hands and eyes with gloves and safety glasses when

changing the lamp.

• Do not stare directly into the light. Never look at an exposed lamp while

it is lit.

• Replace the lamp if it becomes defective or worn out.

Protecting yourself and others from burns and fire

• Never attempt to bypass the thermostatic switch or fuses. Always

replace defective fuses with ones of the specified type and rating.

• Keep all combustible materials (for example fabric, wood, paper) at

least 0.1 meters (4 inches) away from the fixture. Keep flammable

materials well away from the fixture.

8 Mania SCX500 user manual

• Do not illuminate surfaces within 1 meter (3.3 feet) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and

air vents.

• Never place filters or other materials over the lens or mirror.

• Allow the fixture to cool before handling. Allow the fixture to cool for at

least 20 minutes before opening the fixture or removing the lamp.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C

(104° F).

Protecting yourself and others from injury due to

falls

• When suspending the fixture above ground level, verify that the

structure can hold at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely

fastened and use an approved means of secondary attachment such as

a safety cable.

• Block access below the work area whenever installing or removing the

fixture.

Installation 9

2. I

NSTALLATION

AC power

The Mania SCX500 is supplied set up to match local voltage and

frequency. The factory setting is shown on the serial number label. It is not

possible to reconfigure the Mania SCX500 to accept any other voltage or

frequency than those stated on the serial number label.

Warning! For protection from fire and electric shock, the fixture must be

grounded (earthed). The power supply must have overload

and ground-fault protection.

Check that power cables are undamaged and rated for the

current requirements of all connected devices before use.

Check the operating voltage and frequency indicated on the

serial number label before applying power. If your Mania

SCX500 does not match your local AC power, do not use it.

Important! Do not connect the fixture to a dimmer system.

Installing a plug on the power cable

The power cable must be fitted with a grounding-type (earthed) power

plug that matches your power distribution system. Consult a qualified

electrician if you have any doubts about proper installation.

If you need to fit a power plug, follow the plug manufacturer’s instructions,

connecting the yellow and green wire to ground (earth), the brown wire to

live, and the blue wire to neutral. The table below shows some pin

identification schemes:

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

Table 1: Power plug wiring

10 Mania SCX500 user manual

Rigging the Mania SCX500

The Mania SCX500 must be either:

• fastened to a flat surface by means of its adjustable U-bracket,

• fastened to a flat surface by means of its adjustable U-bracket and

mounting plate, or

• attached to a rigging clamp by means of its adjustable U-bracket.

Do not install the fixture by any other means, as this can cause the fixture

to overheat.

Warning! Block access below the work area and work from a stable

platform when installing or servicing the fixture.

Always use a secure means of secondary attachment that can

hold at least 10 times the weight of the fixture.

1. The fixture must be located at least 1 meter (3.3 ft.) away from the

surface to be illuminated and at least 0.1 meters (4 in.) from any

combustible materials (wood, fabric, paper, etc.). Ensure that the

clearance around the fan and air vents is at least 0.1 meters (4 in.).

Ensure that there are no flammable materials nearby.

2. If using a rigging clamp (not included), ensure that the clamp is

undamaged and can bear at least 10 times the fixture’s weight. Bolt the

clamp securely to the fixture’s mounting bracket with a grade 8.8

(minimum) M12 bolt and lock nut through the 13 mm hole in the center

of the mounting bracket, or as recommended by the clamp

manufacturer.

3. If fastening the fixture directly to a mounting surface, ensure that any

fasteners used and the mounting surface can bear at least 10 times the

fixture’s weight. The fixture may be fastened using any of the following:

• four 6.5mm holes in the sides of the U-bracket

• two 8mm holes in the top of the U- bracket

• one 13mm hole in the top of the U-bracket.

Andere Handbücher für Mania SCX500

Inhaltsverzeichnis

Andere Martin Beleuchtungsausrüstung Handbücher

Martin

Martin EC Series LED Video Panel Benutzerhandbuch

Martin

Martin Mania EF3 Bedienungsanleitung

Martin

Martin VC-Feeder Bedienungsanleitung

Martin

Martin RoboScan Pro 918 Bedienungsanleitung

Martin

Martin CX-10 Extreme Bedienungsanleitung

Martin

Martin RoboColor III Bedienungsanleitung

Martin

Martin MAC 575 Krypton Bedienungsanleitung

Martin

Martin MAC 2000 Profile II Bedienungsanleitung

Martin

Martin MAC 700 PROFILE Bedienungsanleitung

Martin

Martin MAC Viper Profile Bedienungsanleitung

Martin

Martin Xciter Bedienungsanleitung

Martin

Martin Magic Moon Bedienungsanleitung

Martin

Martin Exterior 200 LED Bedienungsanleitung

Martin

Martin MiniMAC Wash Bedienungsanleitung

Martin

Martin P3-100 Benutzerhandbuch

Martin

Martin MAC Quantum Wash Bedienungsanleitung

Martin

Martin MAC TW1 Bedienungsanleitung

Martin

Martin MAC 2000 Wash XB Bedienungsanleitung

Martin

Martin MAC 2000 Profile II Bedienungsanleitung

Martin

Martin MAC 575 Krypton Bedienungsanleitung

Martin

Martin M1 HD Bedienungsanleitung

Martin

Martin ColorFox 100 Bedienungsanleitung

Martin

Martin Acrobat Bedienungsanleitung

Martin

Martin MAC Viper Profile Einrichtungshandbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung