Martin MiniMAC Wash Bedienungsanleitung

MiniMAC

user manual

MiniMAC Wash

MiniMAC Profile

1 data connection

2 base fan

3 head fan

4 AC input & main fuse

5 cover locks

6 lamp access

7 control panel

8 eye bolt for safety cable

9 Omega clamp

attachment bracket

reproduced, in any form or by any means, without

permission in writing from Martin Professional A/S,

Denmark.

Printed in Denmark.

P/N 35000084, Rev. A

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

AC POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CONTROL PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CONTROLLER OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

STAND-ALONE OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

GOBOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

BASIC SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

DMX PROTOCOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4Introduction

NTRODUCTION

Thank you for selecting the Martin MiniMAC Profile or MiniMAC Wash. Both of

these automated luminaires provide 12 dichroic color filters, high-speed mechanical

shutter, 540° of pan by 270° of tilt, 3-digit LED control panel, DMX, MC-1, stand-

alone, and master/slave control options; and switch-selectable power supply

settings. The MiniMAC Profile provides a 17° hard-focused beam, manually

adjustable focus, and 7 interchangeable rotating gobos. The MiniMAC Wash

provides a soft-edged 23° beam.

SAFETY INFORMATION

Warning! This product is for professional use only. It is not for household

use.

This product presents risks of lethal or severe injury due to fire and heat, electric

shock, ultraviolet radiation, lamp explosion, and falls. Read this manual before

powering or installing the fixture, follow the safety precautions listed below and

observe all warnings in this manual and on the fixture. If you have questions about

how to operate the fixture safely, please contact your Martin dealer or call the

Martin 24-hour service hotline at +45 70 200 201.

To protect yourself and others from electric shock

• Disconnect the fixture from AC power before removing or installing the lamp,

fuses, or any part, and when not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and electrical

codes and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer all service to a Martin service technician.

To protect yourself and others from UV radiation and lamp

explosion

• Never operate the fixture with missing or damaged lenses and/or covers.

Introduction 5

• When replacing the lamp, allow the fixture to cool for at least 5 minutes before

opening the fixture or removing the lamp. Protect your hands and eyes with gloves

and safety glasses.

• Do not stare directly into the light. Never look at an exposed lamp while it is lit.

• Replace the lamp if it becomes defective or worn out.

To protect yourself and others from burns and fire

• Never attempt to bypass the thermostatic switch or fuses. Always replace defective

fuses with ones of the specified type and rating.

• Keep all combustible materials (for example fabric, wood, paper) at least 0.3 meters

(12 inches) away from the fixture. Keep flammable materials well away from the

fixture.

• Do not illuminate surfaces within 0.3 meters (12 inches) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.

• Never place filters or other materials over the lens.

• The exterior of the fixture can reach temperatures up to 60° C (140° F). Allow the

fixture to cool before handling.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

To protect yourself and others from injury due to falls

• When suspending the fixture above ground level, verify that the structure can hold

at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened and use an

approved means of secondary attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

UNPACKING

The packing material is carefully designed to protect the fixture during shipment -

always use it to transport the fixture.

The MiniMAC comes with:

• Martin Metal Halide 150 lamp

• 3 m, 3-pin IEC mains cable

• 5 m, black, 3-pin XLR data cable

• Attachment bracket for mounting clamp

• Eye bolt for safety cable

•usermanual

6AC power

POWER

The MiniMAC has switch-selectable settings to configure the power supply for

local conditions. The factory-default setting is indicated on the serial number label.

Always use the setting that is closest to the local AC supply.

Warning! For protection from electric shock, the fixture must be grounded

(earthed). The power supply shall have overload and ground-

fault protection.

Important! Install fuse and verify that power supply settings match local

AC supply before use.

To change the voltage setting

1 Disconnect the fixture from power.

2 Remove the 4 base cover bolts with a 4 mm Allen wrench. Move the cover out of

the way of the switches without disconnecting wires.

3 Set the 5-position switch (A) to the setting closest to the AC voltage. Use the

higher setting if the voltage is halfway between 2 settings. For example, use the

230 V setting instead of the 210 V setting for operation with 220 V power.

4 Set the 2-position switch (B) to the AC frequency (50 / 60 Hz).

5 Replace the cover and apply a new power setting label to the serial number

label.

AC power 7

To install the main fuse

Fuses are provided for 100 - 130 V and 200 - 250 V operation. Use only the fuse

specified for the operating voltage.

1 Locate the bag containing the fuse for your AC voltage. Insert the fuse in the

fuse holder. The holder may be packed with the other fuse.

2 Remove the label covering the mains input socket.

3 Insert the fuse holder in the empty slot in the mains input socket (C).

To install a plug on the power cable

The power cable must be fitted with a grounding-type cord cap that fits your power

distribution system. Consult an electrician if you have any doubts about proper

installation.

• Following the cord cap manufacturer’s instructions, connect the yellow and

green wire to ground (earth), the brown wire to live, and the blue wire to neutral.

The table below shows some pin identification schemes.

To apply power

Warning! The power cables must be undamaged and rated for the

electrical requirements of all connected devices.

Important! Powering through a dimmer system can damage the fixture.

• Connect the prepared cable to the mains input socket and the AC mains

distribution system. Do not connect the fixture to a dimmer system.

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

Table 1: Cord cap connections

8Installation

NSTALLATION

LOCATION AND ORIENTATION

For safe operation, install the MiniMAC in a location where

• it is at least 0.3 meters (12 inches) away from illuminated surfaces and combustible

materials.

• it is not easily touched or bumped.

• it is protected from rain and moisture.

• there is at least 0.1 meters (4 inches) clearance around the fans and air vents.

• there are no flammable materials nearby.

The MiniMAC may be installed in any orientation by means of a rigging clamp (not

included) or placed directly on a stage or floor.

The intense light can burn or melt parts within a distance of 0.3 meters (12 inches).

The MiniMAC is programmed to close its shutter if it illuminates its own base for

more than 10 seconds. When installing fixtures side-by-side, avoid illuminating one

fixture with another.

RIGGING

The MiniMAC includes a bracket for attaching a rigging clamp with 12 mm (1/2

in.) hardware. Clamps available from Martin are listed on page 37.

To rig the fixture

WARNING! Screw the included eye bolt securely into the base and fasten a

safety cable to the eye bolt.

1 Verify that the clamp is undamaged and can bear at least 10 times the weight of

the fixture. Verify that the structure can bear at least 10 times the weight of all

installed fixtures, clamps, cables, auxiliary equipment, etc.

2 Bolt a clamp to the included bracket with a grade 8.8 (minimum) M12 bolt and

lock nut, or as recommended by the clamp manufacturer, through the 13 mm

hole in the bracket.

Installation 9

3 Align the bracket with the keyholes in the base. Insert both locking pins into the

holes and turn both levers a full 1/4 turn clockwise to lock.

The fasteners are

locked only when turned fully clockwise.

4 Screw the eye bolt securely into the base as shown below.

5 Block access below the work area.

6 Working from a stable platform, clamp the fixture to the structure.

7 Fasten a safety cable that can bear at least 10 times the weight of the fixture to

the structure and the eye bolt.

10 Control panel

ONTROL

PANEL

The control panel is used to set control modes, address, and personalities, display

information readouts, test, and manually control the fixture.

All user options may be set remotely via the serial link using the Martin MPBB1

Uploader with version 1.4 or later software. Please refer to the MPBB1 manual for

details.

P t

tIn

Pro AdJ

Adr CtrtStPEr

Address/

Info

rst

LOn

LOF

COL

rst

LOn

SHU

COL

tIL

LOF

ALO

rES

dIS

UPL

PCb

UTl

FAC

LOg

StC

SHU

...

EFS

tSE

PtS

P-t

tyP

LOF

SHU

Control menu

Shaded items apply to MiniMAC Profile only.

gob

PAn

InF

tot

rES

LHr

tot

rES

LSt

tot

rES

UEr

gob

rgo

P-t

EnA

trg

rAt

Ctr

SPd

COL

gob

FAC

POS

PAn

tIL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Martin Beleuchtungsausrüstung Handbücher

Martin

Martin Mania EF3 Bedienungsanleitung

Martin

Martin MAC 250+ Bedienungsanleitung

Martin

Martin MAC Aura FX Bedienungsanleitung

Martin

Martin Mania SCX500 Bedienungsanleitung

Martin

Martin EvenLED RGB LED Panel Bedienungsanleitung

Martin

Martin PAL 1200 FX Bedienungsanleitung

Martin

Martin MAC Viper Profile Einrichtungshandbuch

Martin

Martin RoboColor III Bedienungsanleitung

Martin

Martin MAC Viper Profile Bedienungsanleitung

Martin

Martin Exterior Projection 500 Bedienungsanleitung

Martin

Martin Extube Bedienungsanleitung

Martin

Martin MAC 300 Bedienungsanleitung

Martin

Martin MAC 2000 Wash XB Bedienungsanleitung

Martin

Martin MAC 2000 Wash XB Bedienungsanleitung

Martin

Martin Tripix 300 Bedienungsanleitung

Martin

Martin CX-10 Extreme Bedienungsanleitung

Martin

Martin MAC Viper Profile Bedienungsanleitung

Martin

Martin ELP CL Bedienungsanleitung

Martin

Martin MAC 2000 Profile II Bedienungsanleitung

Martin

Martin MAC 2000 Wash XB Bedienungsanleitung

Martin

Martin MAC Viper Profile Bedienungsanleitung

Martin

Martin MAC 500E Bedienungsanleitung

Martin

Martin MAC 575 Krypton Bedienungsanleitung

Martin

Martin MAC 101 Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung