MartinLogan Matinee Bedienungsanleitung

Matinee

user’s manual

Serial Number: _________________________________

Record your serial number here for easy reference. You will need this infor-

mation when filling out your warranty registration. Matinee’s serial num-

ber is located on backplate and on the shipping container.

Thank you—to you, the MartinLogan owner,

for loving what we do,

and

for making it possible for us to do what we love.

4 Contents

Contents

WARNING! Do not use your Matinee loudspeaker outside of the country of original sale—voltage requirements

vary by country. Improper voltage can cause damage that will be potentially expensive to repair. The Matinee is

shipped to authorized MartinLogan distributors with the correct power supply for use in the country of intended

sale. A list of authorized distributors can be accessed at www.martinlogan.com or by emailing info@martinlogan.com.

Contents......................................4

InstallationinBrief .............................5

Introduction...................................6

Connections...................................7

AC Power Connection

Signal Connection

Break-In

Installation....................................8

Installation Options

On-Wall/Off-Wall Acoustic Contour Switch

Using the Non-Skid Grip Feet

Using Matinee With the Stand. . . . . . . . . . . . . . . . . . . . . 9

Mounting the Matinee on a Wall. . . . . . . . . . . . . . . . . . 10

HomeTheater.................................11

Electrostatic Advantages . . . . . . . . . . . . . . . . . . . . . . . . 12

MartinLogan Exclusives . . . . . . . . . . . . . . . . . . . . . . . . . 13

CLS™ (Curvilinear Line Source)

Generation 2 Diaphragm

MicroPerf Stator

In accordance with the European Union WEEE (Waste

Electrical and Electronic Equipment) directive effective

August 13, 2005, we would like to notify you that this

product may contain regulated materials which upon

disposal, according to the WEEE directive, require spe-

cial reuse and recycling processing.

For this reason MartinLogan has arranged with our distrib-

utors in European Union member nations to collect and

The lightning bolt flash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient mag-

nitude to constitute a risk of electric shock.

ElectrostaticHistory............................14

Frequently Asked Questions. . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting...............................18

GeneralInformation...........................19

Specifications

Warranty and Registration

Serial Number

Service

Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . 20

On Non-Sikd Grip Feet

WithBracket .................................21

GlossaryofAudioTerms........................22

recycle this product at no cost to you. To find your local distribu-

tor please contact the dealer from whom you purchased this product,

email [email protected] or visit the distributor locator at www.

martinlogan.com.

Please note, only this product itself falls under the WEEE directive.

When disposing of packaging and other related shipping materials we

encourage you to recycle these items through the normal channels.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

Installation in Brief 5

We know you are eager to hear your new MartinLogan

loudspeaker, so this section is provided to allow fast and

easy set up. Once your new speaker is operational, please

take the time to read, in depth, the rest of the informa-

tion in the enclosed manual. It will give you perspective

on how to attain the greatest possible performance from

this most exacting transducer.

If you should experience any difficulties in the setup or

operation of your MartinLogan speaker, please refer to

the Connections section of the user’s manual.

Should you encounter a persistent problem that cannot

be resolved, please contact your authorized MartinLogan

dealer. They will provide you with the appropriate techni-

cal analysis to alleviate the situation.

WARNING!

• Hazardousvoltagesexistinside—donot

remove cover.

• Referservicingtoaqualifiedtechnician.

• Topreventfireorshockhazard,donot

expose this module to moisture.

• Turnamplifieroffandunplugspeakershould

any abnormal conditions occur.

• Turnamplifieroffbeforemakingorbreaking

any signal connections!

• Donotoperateifthereisanyvisualdamage

to the electrostatic panel element.

• Donotdrivespeakerbeyonditsratedpower.

• Thepowercordshouldnotbeinstalled,

removed, or left detached from the speaker

while the other end is connected to an AC

power source.

• Nocandlesorothersourcesofopenflame

should be placed on the speaker.

• Noliquidseitheringlassesorvasesshouldbe

placed on speaker.

• Speakershouldnotbeexposedtodrippingor

splashing liquids.

• Theterminalsmarkedwiththelightningbolt

symbol should be connected by an instructed

person or by way of ready made terminals

• Topreventinjury,thisapparatusmustbe

securely attached to the floor/wall in accor-

dance with the installation instructions.

Step 1: Unpacking

Remove your new MartinLogan speakers from its packing.

Retain the packaging in a safe, dry place for future use.

Step 2: Placement

Place the speaker at the desired location. Please see the

Installation section (pages 9–10) for more details.

Step 3: Power Connection (AC) (see warning)

MartinLogan speakers require power to energize their

electrostatic panels. Using the power cords provided,

plug first to the power in receptacle on the rear panel

of the speaker, making sure that you have made a firm

connection, and then to the wall outlet. Please see the

Connections section (page 7) for more details.

Step 4: Signal Connection

Usethebestspeakercablesyoucan.Higherqualitycable,

available from your specialty dealer, is recommended and

will give you superior performance. Spade connectors are

suggested for optimum contact and ease of installation.

Attach your speaker cables to the Signal Input section on

the rear panel. Be consistent when connecting speaker

leads to the terminals on the back of the speaker: take

great care to assign the same color to the (+) terminal on

the speaker and the amplifier. Please see the Connections

section (pages 7) for more details.

Step 5: Listen and Enjoy

InstallatIon In BrIef

6 Introduction

Congratulations! You have invested in one of the

world’s premier loudspeaker systems.

The MartinLogan Matinee represents an advanced

combination of sonic technologies establishing an unprec-

edented direction for audiophile design. The result of

years of research, the new Matinee™ hybrid electrostat-

ic loudspeaker establishes new standards for efficiency,

dynamics and precision in a loudspeaker.

Matinee’s CLS transducer builds upon the legacy of

MartinLogan’s electrostatic heritage with the incorpora-

tion of advanced vacuum bonding and MicroPerf stat

panels, providing even greater efficiency and precision.

The integration electrical interface technology devel-

oped by MartinLogan’s Statement™ e2 engineering team

extends effortless dynamics and purity, resulting in even

higher sonic standards of efficiency and precision.

Through rigorous testing, MartinLogan’s curvilinear electro-

static panel has proven itself to be one of the most durable

and reliable transducers available today. Fabricated from a

custom tool punched high-grade steel, the patented

panel is then coated with a special polymer that is applied

via a proprietary electrostatic bonding process. This panel

assemblyhousesamembranejust0.0005ofaninchthick.

Ruggedly constructed and insulated, the panel is rated to

easily handle up to 150 watts of continuous power with

no deleterious effects.

Featuring an advanced crossover topology derived from

engineering established with he Summit loudspeaker,

MartinLogan engineered the Matinee™ crossover using

precision audiophile-grade polypropylene capacitors and

high-purity air-core coils. This advanced crossover topol-

ogy flawlessly preserves sonic subtleties while effortlessly

handling the broadest range of dynamics.

The materials in your new Matinee speaker are of the

highest

quality and will provide years of enduring

enjoymentand

deepening respect. The cabinetry is con-

structed from dense composite material for acoustical

integrity.

The other sections of your User’s Manual explain in detail

the operation of your Matinee speaker and the philoso-

phy applied to their design. A clear understanding of your

speaker will insure that you obtain maximum perfor-

mance and pleasure from this most exacting transducer.

It has been designed and constructed to give you years of

trouble-freelisteningenjoyment.

IntroduCtIon

Connections 7

ConneCtIons

AC Power Connection

Your Matinee uses an external low-voltage power sup-

ply to energize its electrostatic panel. For this reason the

proper low-voltage power supply is provided. The power

supply should be firmly inserted into the ‘Power In’ recep-

tacle on the rear connection panel of the speaker, then to

any convenient AC wall outlet (see figure 1). Your Matinee

integrates a signal sensing circuit which will switch the

Matinee off after a few minutes of no music signal, and

requires less than two seconds to recharge the panel when

a music signal is present.

Your Matinee speaker is provided with a power supply

for the power service supplied in the country of original

consumer sale. The AC power rating applicable to a par-

ticular unit is specified both on the packing carton and on

the power supply.

If you remove your Matinee speakers from the country of

original sale, be certain that the AC power supplied in any

subsequent location is suitable before connecting the low-

voltage power supply. Substantially impaired performance

or severe damage may occur to a Matinee speaker if oper-

ation is attempted from an incorrect AC power source.

WARNING! The power supply should not

be installed, removed, or left detached from

the speaker while connected to an AC power

source.

Signal Connection

Use the best speaker cables you can. The length and type

of speaker cable used in your system will have an audible

effect. Under no circumstance should a wire of gauge

higher (thinner) than #16 be used. In general, the lon-

ger the length used, the greater the necessity of a lower

gauge, and the lower the gauge, the better the sound,

with diminishing returns setting in around #8 to #12.

A variety of speaker cables are now available whose

manufacturers claim better performance than standard

heavy gauge wire. We have verified this in many cases,

and the improvements available are often more notice-

able than the differences between wires of different

gauge. The effects of cables may be masked if the equip-

ment is not of the highest quality.

Connections are made at the signal input section on the

rear electronics panel of the Matinee (see figure 1). Use

spade connectors for optimum contact. Make certain that

all of your connections are tight. Be consistent when con-

necting speaker leads to the terminals on the back of the

Matinee. Take great care to assign the same color to the

(+) terminal on both the speaker and the amplifier.

WARNING! Turn your amplifier off before mak-

ing or breaking any signal connections!

Break-In

When you first begin to play your Matinee speaker, it will

sound a bit bass shy. This is due to the high-quality, long-

life components used in the woofers. These custom made

woofer requires at least 80 hours of break-in at 90 dB

(moderate listening levels) before any critical listening. The

break-in requirements of the crossover components (and,

to a lesser degree, the electrostatic transducer) are equal.

Figure 1. Power and signal connection.

8 Installation

InstallatIon

On the Television

If your television provides a wide, level and stable plat-

form, the Matinee can be placed directly on top of the

television (see figure 2). The non-skid rubber grip feet

should be used beneath the Matinee to provide traction.

On the Floor

Placing the Matinee on the floor might position it too low

to blend with the front speakers. If placing the Matinee

on the floor is the best placement for your system, the

adjustablestand(soldseperately)willallowyoutotiltthe

Matinee towards the listening position.

On the Wall

The included brackets allow you to mount the Matinee

on the wall (see figures 3 and “Mounting the Matinee On

A Wall,” page 10).

WARNING! Installation other than that

described in the body of this document requires

specific documentation from MartinLogan.

Installation Options

Figure 3. Matinee installation on a wall.

Figure 2. Matinee installation on a television.

Installation 9

On-Wall/Off-Wall Acoustic Contour Switch

Figure 4. IfMatineeistobeusedwiththeoptionaladjustablestand,

place the non-skid grip feet on the stand and beneath the speaker.

Matinee features a unique ‘on-wall/off-wall’ switch that

tailors acoustic equalization to either installation option.

Simply set this switch to On-Wall if mounting to a surface.

Set the switch to Off-Wall if the Matinee is more than four

inches from a wall. Setting this switch ensures that you will

achieve total system matching in even the most diverse

setups (such as systems mixing on-wall and off-wall instal-

lations).

Using the Non-Skid Grip Feet

When setting Matinee on a surface, use the non-skid Grip

Feet beneath the speaker to provide traction (see figure 4).

10 Installation

Mounting the Matinee On A Wall

Required hardware (included):

(6) Wall Anchors

 (6)1”PhillipsHeadWoodScrews

(2) Push pins

(2) Wall Brackets

(2) Shoulder Bolts

(2) Threaded Rubber Bumpers

Required tools (not supplied):

Level

Pencil

Electric Drill

1/8” (0.125”) Drill Bit

1/4” (0.25”) Drill Bit

 PhillipsHeadScrewdriver

NOTE: These instructions assume the mounting surface is

of wood frame and standard sheet rock construction. If you

wish to mount the Matinee to another type of material or

construction, you should consult a bonded contractor.

NOTE:Beforebeginning,studytheHorizontaland

VerticalHardwareConfigurationdrawings(figures5&6).

IMPORTANT! This template is used for both horizontal

and vertical installations. When drilling pilot holes and

tracing keyholes make sure you’re using the 2 pilot hole

and 2 keyhole locations intended for your installation.

1 Position the template. Install the center push pin.

2 Level the template. Install the second push pin.

3 Using a pencil trace two keyholes located on the template.

4 Using a 1/8-inch drill bit, drill two pilot holes located

on the template.

5 Remove the template.

6 If a pilot hole does not hit a stud use a 1/4-inch drill bit

to widen the hole and install a wall anchor.

7 Install both wall brackets using only the top screw. Do

not over tighten the top screw.

8 Align each wall brackets keyhole with a traced keyhole

and tighten the top screw.

9 On the back of the Matinee, install two shoulder bolts

in the top holes and two rubber bumpers in the bottom

holes.Testfitthespeaker.Adjustthebracketpositions

until the speaker fits. IMPORTANT! At this point do

not allow the speaker to hang freely—there are not

enough screws installed to fully support its weight.

10 Drill two more pilot holes (per bracket) at the screw hole

locationsontheleft&rightsidesofbothwallbrackets.

11 If a pilot hole does not hit a stud remove the wall

bracket , use a 1/4-inch drill bit to widen the hole, and

install a wall anchor.

12 Install both wall brackets using all 3 screws per bracket.

Tighten the screws.

13 Hangthespeakeronthewallbrackets.

Figure 5.VerticalHardwareConfiguration

Figure 6.HorizontalHardwareConfiguration

Inhaltsverzeichnis

Andere MartinLogan Sprecher Handbücher

MartinLogan

MartinLogan Vantage Bedienungsanleitung

MartinLogan

MartinLogan bravado Bedienungsanleitung

MartinLogan

MartinLogan Helos 12 Bedienungsanleitung

MartinLogan

MartinLogan Preface Bedienungsanleitung

MartinLogan

MartinLogan STAGECenter Channel Speaker Bedienungsanleitung

MartinLogan

MartinLogan Quest z Bedienungsanleitung

MartinLogan

MartinLogan ML-60 Bedienungsanleitung

MartinLogan

MartinLogan Motion 20 Bedienungsanleitung

MartinLogan

MartinLogan In-Wall Loudspeaker Bedienungsanleitung

MartinLogan

MartinLogan classic ESL 9 Bedienungsanleitung

MartinLogan

MartinLogan pmn Bedienungsanleitung

MartinLogan

MartinLogan Motion MC4 Bedienungsanleitung

MartinLogan

MartinLogan Purity Bedienungsanleitung

MartinLogan

MartinLogan STAGE Bedienungsanleitung

MartinLogan

MartinLogan Speaker Bedienungsanleitung

MartinLogan

MartinLogan Motion SLM Bedienungsanleitung

MartinLogan

MartinLogan Motion 20 Bedienungsanleitung

MartinLogan

MartinLogan Xstat Summit X Bedienungsanleitung

MartinLogan

MartinLogan Center Channel Speaker Logos Bedienungsanleitung

MartinLogan

MartinLogan Motion FX Bedienungsanleitung

MartinLogan

MartinLogan ElectroMotion C2 Bedienungsanleitung

MartinLogan

MartinLogan Source Speakers Bedienungsanleitung

MartinLogan

MartinLogan Motion LX16 Bedienungsanleitung

MartinLogan

MartinLogan Odyssey Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung