MartinLogan Statement 40XW Bedienungsanleitung
Driver Assembly Manual
®
2
WARNING!
• Refer servicing to a qualified technician.
• To prevent fire or shock hazard, do not
expose this module to moisture.
• Turn the amplifier off should any abnormal
conditions occur.
• Do not drive speaker beyond its rated power.
Content Check List............................ 3
Connection................................. 4
Protect Your Investment........................ 4
Break-In................................... 4
Speaker Placement ........................... 4
Achieving Superior Imaging . . . . . . . . . . . . . . . . . . . .4
Balancing Hard vs. Soft Surfaces Improves
High- and Mid-Frequency Performance ............4
Painting the Speaker Grille ..................... 5
Pre-Installation Checklist ....................... 6
Part Identification ............................ 7
Installation ..............................8 - 14
Driver Assembly Installation Preparation ...........8
Attach Trim Pieces ...........................9
Mounting The Driver Assembly .................10
Securing The Driver Assembly..................11
Attach The Front Baffle Trim ...................12
(Optional) Apply The Logo Badge...............13
(Optional) Apply The Speaker Grille . . . . . . . . . . . . .14
Dimension Drawing. ......................... 15
Specifications .............................. 16
Per the European Union WEEE (Waste Electrical and
Electronic Equipment) directive effective August 13,
2005, we would like to notify you that this product
may contain regulated materials which upon disposal,
according to the WEEE directive, requires special reuse
and recycling processing. For this reason, Martin Logan
has arranged with our distributors in European Union
member nations to collect and recycle this product at
no cost to you.
To find your local distributor, please contact the dealer
from whom you purchased this product, email
www.martinlogan.com.
Please note, only this product itself falls under the
WEEE directive. When disposing of the packaging and
other related shipping materials, we encourage you to
recycle these items through the usual channels.
The lightning bolt flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
The fire within an equilateral triangle is intended
to alert the user to the potential of creating a fire
hazard if they do not follow the instructions.
The dollar sign within an equilateral triangle is
intended to alert the user that they run the risk
of causing damage that could be potentially
expensive to repair if they don’t follow the
instructions.
3
Content Check List
A complete Statement 40XW is shipped in 3 boxes. This manual refers to box 3 of 3 which is the Driver Assembly. The
Statement 40XW Driver Assembly contains the following items.
Should you require assistance, please call our service department at (785) 749-0133.
40XW Driver Assembly • Front Baffle Trim • Speaker Grille Cover • Extra Grille Scrim • Trim Pieces • Machine Screws
4x Brass Screws • MartinLogan Logo Badge and Template
4
The amplifier is connected to the Statement 40XW through the
binding posts located on the top or bottom of the in wall back
box.
4 brass screws on the front of the speaker baffle are used to
establish the connection with the amplifier.
See pg. 11 for additional details on making this connection.
ConneCtion
• Use an amp that approximately matches the speaker’s
specified power handling.
• To avoid damage, turn down the volume of the
speaker is distorting, sounds harsh, or the bass begins
to break up.
• Tone controls and equalizers may increase the
likelihood of distortion, especially at high volumes. Use
these setting sparingly.
When you first begin to play your speakers, they may sound
a bit bass shy, due to the high quality, long-life components
used in the drivers. Allow approximately 72 hours of break-in at
90 dB (moderate listening levels) before any critical listening.
Break-in
ProteCt Your investment
Achieving Superior Imaging
For best performance and imaging, place the speakers
equidistant to the primary listening position. It is
recommended that the primary listening position be 1x -2x
the distance between the speakers for optimal imaging. For
example, if your speakers are 10 feet apart, then the optimal
listening distance is between 10 and 20 feet away. Guidance
for speaker height can be found on page 6 in the “Pre-
Installation Checklist” section.
Balancing Hard vs. Soft Surfaces Improves High- and
Mid-Frequency Performance
Rooms that are “overdamped” with carpeting, drapes, and
other sound absorbers can cause your system to be dull
and lifeless. On the other hand, rooms can have so many
hard surfaces that the system sounds like a gymnasium.
Experiment by adding or removing soft surfaces until you find
a mix that is right for you.
sPeaker PlaCement
Fig. 1
WARNING! Turn your amplifier off before
making or breaking any signal connections!
5
Painting the sPeaker grille
IMPORTANT!
Before painting, remove the grille from speakers
and remove the cloth scrim attached inside the grille. The
speaker includes an extra scrim.
1. Remove the grille from the speaker. A protective cloth
scrim is attached to the back of the grille with a low-tack
adhesive. Remove this scrim by gently pulling it away
from the grille and discard it.
2. Paint the grille, being careful not to plug the holes.
Allow the paint to dry completely before proceeding.
IMPORTANT! For best results use a spray rather than a
brush or roller.
3. Gently press the new scrim into place before reinstalling
the speaker grille.
6
Pre-installation CheCklist
NOTE: This is the second part of the Installation process.
Do not proceed until all steps in the “In-wall Back Box
Manual” have been completed.
If using the Statement On-Wall Enclosure you may pro-
ceed from Step 17.
Required Tools:
-3/32 Hex Bit (Not Included)
-5/32 Hex Bit (Not Included)
-Power Drill
-#2 Philips Bit
-#2 Hand Screwdriver
-Medium Grit Sanding Sponge
PLEASE NOTE: INSTALLATION IS A 2 PERSON JOB.
7
Part identifiCation
3
1
3
3
2
3
6
5
4
7
1Driver Assembly
2Baffle Protector
3Handles
4Trim Baffle
5End Trim
6Side Trim
7Grille
8
sPeaker installation
STEP 16: DRIVER ASSEMBLY INSTALLATION PREPARATION
16a To prepare the back box for the driver assembly
installation, first remove the positioning brackets, 2
corner brackets, and 4 side brackets using a Phillips
screwdriver. These brackets are held in place with 2
screws each.
16b Remove the 10 screws securing the positioning board
and then carefully remove it from the back box.
9
STEP 17: ATTACH TRIM PIECES
17a Before applying the trim pieces, check the interior metal
edge of the install board opening. Sand away any
sheet rock mud buildup so the trim will sit flush with the
surface.
17b Using #2 Phillips screwdriver. apply the top and bottom
trim pieces first, using the supplied machine screws.
(These screws will be in the trim packaging.)
17c Apply the side trim pieces the same way as the top and
bottom pieces.
NOTE: If using the optional on-wall enclosure instead of the
in-wall installation method, please ignore any references to
sheet rock or sheet rock mud, as they only apply to the
in-wall method of installation. All other steps apply to both
methods of installation.
10
STEP 18: MOUNTING THE DRIVER ASSEMBLY
THIS STEP REQUIRES 2 PEOPLE TO COMPLETE SAFELY
18a With 2 people, lift the driver assembly from its
packaging using the attached handles.
18b With 2 people, carefully seat the driver assembly into
the back box by guiding the driver assembly alignment
pins into the mating holes on the back box. Be careful
not to damage the wall surface during this step.
18c While 1 person continues to hold the driver assembly
securely in place, the other should install the included
8-32 screws through the driver assembly into the back
box. These specific locations are marked as “through”
holes in the attached plastic baffle protector. (3/32 hex
driver bit required for machine screws. Not included)
18d Once all 8-32 screws have been tightened, the driver
assembly is now securely attached to the back box.
The person holding the driver assembly in place can
now let go.
18e You may now safely remove the handles and plastic
baffle protector from the driver assembly. (Handle
removal will require the 5/32 hex driver bit. Not
included.)
NOTE: Left channel orientation shown here. Right channel
will be mirrored.
x 4 x 4
Andere Handbücher für Statement 40XW
1
Inhaltsverzeichnis
Sprachen:
Andere MartinLogan Sprecher Handbücher
MartinLogan
MartinLogan Xstat Summit X Bedienungsanleitung
MartinLogan
MartinLogan Ascent LoudSpeaker Bedienungsanleitung
MartinLogan
MartinLogan Motion I5 Bedienungsanleitung
MartinLogan
MartinLogan MONTAGE Bedienungsanleitung
MartinLogan
MartinLogan Motion MC4 Bedienungsanleitung
MartinLogan
MartinLogan Monument 7XW Bedienungsanleitung
MartinLogan
MartinLogan Illusion ESL C34A Bedienungsanleitung
MartinLogan
MartinLogan FRESCO Bedienungsanleitung
MartinLogan
MartinLogan i Bedienungsanleitung
MartinLogan
MartinLogan Installer Series Bedienungsanleitung
MartinLogan
MartinLogan Purity Bedienungsanleitung
MartinLogan
MartinLogan Vanquish Bedienungsanleitung
MartinLogan
MartinLogan Center Channel Speaker Logos Bedienungsanleitung
MartinLogan
MartinLogan EM-ESL C Bedienungsanleitung
MartinLogan
MartinLogan Vista Bedienungsanleitung
MartinLogan
MartinLogan Motion XTW6 Bedienungsanleitung
MartinLogan
MartinLogan Motion FX Bedienungsanleitung
MartinLogan
MartinLogan Motion 60XT Bedienungsanleitung
MartinLogan
MartinLogan Motion XT F200 Bedienungsanleitung
MartinLogan
MartinLogan CLX Bedienungsanleitung
Beliebte Sprecher Handbücher anderer Marken
Bowers & Wilkins
Bowers & Wilkins 4 Bedienungsanleitung
Sonance
Sonance SONOS OUTDOOR Series Bedienungsanleitung
Electro-Voice
Electro-Voice EVID FM4.2 Bedienungsanleitung
Pioneer
Pioneer XW-HTD630 Bedienungsanleitung
Onn
Onn BWA16AA002 Bedienungsanleitung
HP
HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung