Master cool 71400 Bedienungsanleitung
User Guide and Parts List
Warning! Wear safety goggles when using this tool.
GM Fuel Line Tube
Flaring Tool Set
Part# 71400
NEWS...
OTHER AVAILABLE ADAPTERS & DIE SETS
71400-INSTwww.mastercool.com
Pre-operation set-up
•O pen the relief valve to fully recess
the piston, then close tightly.
•R otate the yoke fully counter clock-wise
to bottom out the adapter seat.
• READY TO GO!
45ºDouble Flaring Adapters and Die Sets:
Part# Description
71097-01 45º Flaring Cone
71097-03 3/16" Double Flare adapter
71097-13 3/16" Double Flare die set
71097-04 1/4" Double Flare adapter
71097-14 1/4" Double Flare die set
71097-05 5/16" Double Flare adapter
71097-15 5/16" Double Flare die set
71097-06 3/8" Double Flare adapter
71097-16 3/8" Double Flare die set
71097-08 1/2" Double Flare adapter
71097-18 1/2" Double Flare die set
Part# Description
71205 5/16" Push Connect adapter
71215 5/16" Push Connect die set
71206 3/8" Push Connect adapter
71216 3/8" Push Connect die set
71204 1/4" Push Connect adapter
71214 1/4" Push Connect die set
"World Class Quality"
R
"World Class Quality"
R
Push Connect Adapters and Die Sets:
GM FUEL LINE FLARING INSTRUCTIONS
Rotate the yoke fully
counter-clockwise.
Place the adapter
onto the adapter seat
on the end of the
piston.
Insert the tube
between the dies so
it is even with the
edge as shown.
Insert and tighten the
dies and tubing into the
yoke. (Important to
securely fasten before
moving on to step #4.)
Begin squeezing the
lever and continue until
the edge of the adapter
meets the die.
Release the pressure
by opening the relief
valve.
Grasp the yoke and rotate the
tool counter-clockwise to remove
the adapter from the die.
Loosen the tightening bar and
remove the tube. It should look
something like the sketch below.
OPEN CLOSE
dapter
eat
dapter
ecurely fasten die by turning
tightening bar clockwise.
oke
Relief valve
ube should be
even with die
as shown.
Grasp the yoke and rotate
the hydraulic cylinder
clockwise until it stops.
he adapter should be
of the way into the die
hen you
rotate the
cylinder the
adapter will
travel towards
the die.
o not loosen
tightening bar
until adapter is
outside of the dies.
ome resistance
while turning is
normal.
inished
Push
onnect
lare
OPEN CLOSE
OPEN CLOSE
S
P
F
P
ube
GM F L A S
P
G uel Line dapter
G uel Line ie et
G uel Line dapter
G uel Line ie et
T S
T
lose te relief valve.
e yraulic flui is too col. lose te relief valve an
pump te lever several times to arm te oil.
T P C F
fter te tubing is positione in te tool te yoe must be
rotate into te ie before one begins to sueee te lever.
e igtening ar must be very tigt.
T
fter flaring you must rotate te yoe counterclocise
to pull te aapter out of te tubing. is must be one
prior to releasing te tigtening bar an attempting to
remove te tubing.
TECNICAL ASSIST
ANCE P
INST
P
ydra-flare assembly
GM F L
F T S P L
Andere Master cool Werkzeuge Handbücher
Master cool
Master cool 70078 Bedienungsanleitung
Master cool
Master cool HYDRA-KRIMP Bedienungsanleitung
Master cool
Master cool 71700 Bedienungsanleitung
Master cool
Master cool 69925 Bedienungsanleitung
Master cool
Master cool 43014 Bedienungsanleitung
Master cool
Master cool 43012 Bedienungsanleitung
Master cool
Master cool 70070 Bedienungsanleitung
Master cool
Master cool 70053 Bedienungsanleitung
Master cool
Master cool 43305 Bedienungsanleitung
Master cool
Master cool HYDRA-SWAGE Bedienungsanleitung
