MasterCraft 058-8434-4 Bedienungsanleitung

INSTRUCTION MANUAL

AIR-POWERED

CLIPPED-HEAD FRAMING NAILER

058-8434-4

TABLE OF CONTENTS

AIR-POWERED CLIPPED-HEAD FRAMING NAILER 058-8434-4

QUICK START GUIDE

TECHNICAL SPECIFICATIONS 3

SAFETY GUIDELINES 4–9

KEY PARTS DIAGRAM 10

IMPORTANT INFORMATION 11–13

TYPES OF NAILS 14–15

OPERATING INSTRUCTIONS 16–22

MAINTENANCE 23–24

TROUBLESHOOTING 25–27

EXPLODED VIEW 28

PARTS LIST 29–30

WARRANTY 31–32

SAFETY GUIDELINES

AIR-POWERED CLIPPED-HEAD FRAMING NAILER 058-8434-4

Safety guidelines

This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING

EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it

thoroughly before using the product. The symbols listed below are used to indicate this information.

Note- The word “Note” is used to inform the

reader of something he/she needs to know about

the tool.

PERSONAL SAFETY

These precautions are intended for the personal safety of the user and others working with the user.

Please take time to read and understand them.

DANGER!

Potential hazard that will result in serious

injury or loss of life.

WARNING!

Potential hazard that could result in

serious injury or loss of life.

CAUTION!

Potential hazard that may result in

moderate injury or damage to equipment.

SAFETY GUIDELINES

AIR-POWERED CLIPPED-HEAD FRAMING NAILER 058-8434-4

SAFETY GUIDELINES

Note: Carefully read and understand all the instructions in this manual before using the tool. Ensure

that the operator has read and understood these instructions.

DANGER!

Potential hazard that will result in serious injury or loss of life.

•Keep children away from the work area. Do not allow children to handle

power tools.

•Keep air hose away from heat, oil, and sharp edges. Check air hose for

wear before each use and ensure that all connections are proper.

•Always ensure that the workpiece is firmly secured leaving both hands free

to control the tool.

•Always ensure that the tool has stopped before putting it down after use, in

the interest of safety and to prevent possible damage to the tool/user.

•Keep proper footing at all times in order to ensure correct balance.

•Do not use oxygen or any other combustible or bottled

gas to power air-powered tools. Failure to observe this

warning can cause explosion and serious personal injury

or death. Use only the compressed air to power air-

powered tools. Use a minimum of 25'(7.6 m) of hose to

connect the tool to the compressor. Failure to comply will

result in serious injury or loss of life.

•Risk of electric shock: Do not expose a compressor to rain. Store it indoors.

Disconnect the compressor from the power source before servicing.

Compressor must be grounded. Do not use grounding adaptors.

Oxygen

Hydrogen

Explosive

Combustible

MC-OM-02

SAFETY GUIDELINES

AIR-POWERED CLIPPED-HEAD FRAMING NAILER 058-8434-4

•Risk of personal injury: Do not direct compressed air from the air hose

toward the user or other personnel.

•Risk for breathing: Never directly inhale the air produced by the compressor.

•Risk of bursting: Do not adjust the pressure switch or safety valve for any

reason. They have been preset at the factory for this compressor’s maximum

pressure. Tampering with the pressure switch or the safety valve may cause

personal injury or property damage.

•Risk of burns: The pump and the manifold generate high temperatures. In

order to avoid burns or other injuries, do not touch the pump, the manifold,

or the transfer tube while the compressor is running. Allow the parts to cool

down before handling or servicing. Keep children away from the compressor

at all times.

•Risk of bursting: Make sure the regulator is adjusted so

that the compressor outlet pressure is set lower than the

maximum operating pressure of the tool. Before starting

the compressor, pull the ring on the safety valve to make

sure the valve moves freely. Drain water from tank after

each use. Do not weld or repair tank. Relieve all pressure

in the hose before removing or attaching accessories.

MC-OM-22

SAFETY GUIDELINES

AIR-POWERED CLIPPED-HEAD FRAMING NAILER 058-8434-4

WARNING!

Potential hazard that could result in serious injury or loss of life.

•Do not allow unskilled or untrained individuals to operate the Air-powered

Clipped-Head Framing Nailer.

• Do not use the Air-powered Clipped-Head Framing Nailer for any task other

than that it is designed to perform.

• Do not use the Air-powered Clipped-Head Framing Nailer unless it has been

instructed to use.

•Locate the compressor in a well-ventilated area for cooling, at a minimum of

12"(31 cm) away from the nearest wall.

•Protect the air hose and the power cord from damage and puncture. Inspect

them for weak or worn spots every week, and replace them if necessary.

•Always wear hearing protection when using the air compressor. Failure to do

so may result in hearing loss.

•Do not carry the compressor while it is running.

•Do not operate the compressor if it is not in a stable position.

•Do not operate the compressor on a rooftop or an elevated position that

could allow the unit to fall or be tipped over.

•Always replace a damaged gauge before operating the unit again.

SAFETY GUIDELINES

AIR-POWERED CLIPPED-HEAD FRAMING NAILER 058-8434-4

CAUTION!

Potential hazard that may result in moderate injury or damage to

equipment.

•Always ensure that the tool has stopped before connecting it to the air

supply.

•Do not wear watches, rings, bracelets, or loose clothing when using any air

tool.

•Do not overload the tool. Allow the tool to operate at its optimum speed for

maximum efficiency.

• Do not use a tool that is leaking air, with missing or damaged parts, or that

requires repairs. Verify that all screws are securely tightened.

• For optimal safety and tool performance, inspect the tool daily in order to

ensure free movement of the trigger, safety mechanisms, and springs.

•Always keep your air tool clean and lubricated. Daily lubrication is essential

to avoid internal corrosion and possible failures.

• Ensure the floor is not slippery and wear non-slip shoes. Floor should be

kept clean and clear.

• Always follow all workshop safety rules, regulations, and conditions when

using the Air-powered Clipped-Head Framing Nailer.

•Carry the tool by the handle only, keeping the finger away from the trigger.

Do not carry the tool by the hose, magazine or any other parts.

•Do not use the tool near or below the freezing condition, as doing so may

cause tool failure.

•Do not store the tool in a freezing environment to prevent ice formation on

the operating valves of the tool, as doing so may cause tool failure.

•Handling and storage of oil: Use with adequate ventilation. Avoid contact of

oil with eyes, skin, and clothing. Avoid breathing spray or mist. Store in a

tightly closed container in a cool, dry, well-ventilated area free from

incompatible substances.

SAFETY GUIDELINES

AIR-POWERED CLIPPED-HEAD FRAMING NAILER 058-8434-4

Note: Recycle the unwanted materials rather than disposing of it as waste. Sort the tools, hoses, and

packaging in specific categories and take to the local recycling center or dispose of it in an

environmentally safe way.

CAUTION!

Potential hazard that may result in moderate injury or damage to

equipment.

•Disconnect the tool from the air supply and turn off the

compressor before performing any maintenance, or changing

accessories, when the tool is not in use, when it is being

handed to another person, and when it is left unattended.

Failure to comply may result in moderate injury or damage

to equipment.

•Use safety goggles and ear protection:

Wear safety glasses with side shields when operating the

tool/compressor and verify that others in the work area are

also wearing safety glasses. Safety glasses must conform to

American National Standards Institute (ANSI Z87.1)

requirements and must provide protection from flying

particles from the front and the sides.

Air-powered tools are loud and the sound can cause hearing

damage. Always wear ear protection to prevent hearing

damage and loss. Failure to comply may result in moderate

injury.

MC-588434-01MC-588434-01

MC-OM-01

Inhaltsverzeichnis

Andere MasterCraft Nagelpistole Handbücher

MasterCraft

MasterCraft 058-8691-0 Bedienungsanleitung

MasterCraft

MasterCraft Air-Powered Brad Nailer/Stapler Bedienungsanleitung

MasterCraft

MasterCraft AIR-POWERED BRAD NAILERS Bedienungsanleitung

MasterCraft

MasterCraft 058-8179-2 Bedienungsanleitung

MasterCraft

MasterCraft 058-8691-0 Bedienungsanleitung

MasterCraft

MasterCraft 058-9816-0 Bedienungsanleitung

MasterCraft

MasterCraft AIR-POWERED 2-IN-1 NAILER Bedienungsanleitung

MasterCraft

MasterCraft 058-8489-4 Bedienungsanleitung

MasterCraft

MasterCraft 058-8198-6 Bedienungsanleitung

MasterCraft

MasterCraft Maximum 54-2963-8 Bedienungsanleitung

MasterCraft

MasterCraft 058-8122-6 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung