Matrix PROTON 103 Bedienungsanleitung

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 1/12

PROTON 103

Quick Start

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 2/12

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 3/12

PROPRO

PROTT

TON 103ON 103

ON 103ON 103

ON 103

The Compact Communicator

Quick Start

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 4/12

Thank you for choosing the Matrix PROTON 103! Please read the instructions in

this Quick Start carefully to install and program this ultra-compact, Small and

Home Office PBX.

Know your PROTON 103

The PROTON 103 is an entry-level PBX with one trunk and three stations. The

three stations are numbered as 2, 3 and 4 respectively.

Figure 1: Overview of PROTON 103.

Jumper (J5)

Trunk Port Station Ports (1-3)

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 5/12

Figure 2: Trunk Port and Station Ports.

Push back the

Trunk Terminal

using thumb.

Push back the

Station 1 (2) Terminal

using thumb.

Connect

Wires.

Connect

Wires.

Figure 3: Default Jumper Position.

A-B Position B-C Position

Figure 4: LED indication.

Power

Trunk 1

Stations

(2, 3, 4)

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 6/12

Figure 5: Removing the cover of PROTON 103.

Push down with

fingers.

Before you Start

1. Verify the package contents

Unpack the box. Make sure that the package contains all the following

items. If any item is missing or damaged, please contact the dealer/

reseller who sold you the PBX.

PROTON 103

CD containing the System Manual, Quick Start and

User Card.

Quick Start and

User Card

Two Screw Grips (wall plugs)

Two Screws M 7/30

A Mounting Template

A 150 mA Fuse

Warranty Card Set

2. Get your Trunk and Station Cables ready

For the Trunk and Stations, use a standard telephone cable (two-pair twisted

cable with 0.5mm connector). The length of the station cable may be extended

up to 800 meters.

Strip the ends of the trunk and station cables to be inserted on the system

side about 1 cm to ensure firm and neat contacts.

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 7/12

3. Get your Station Telephones ready

You will need three Single Line Telephones to connect as stations. Any ordinary

push button phone, with or without Call Line Display, even cordless phones

can be connected to the PROTON 103.

IMPORTANT: Use single line telephones equipped with a Flash key, as

several of the features supported by PROTON 103 require you to dial the

‘Flash’ Key. If your phone does not have a Flash key, tap the Hook switch

to dial Flash.

Step 1: Installing PROTON 103

1. Select a suitable place on the wall to mount PROTON 103. Use the wall

mount template provided to mark the nail holes on the wall. Drill two

holes of appropriate size. Fix the two M 7/30 screws (supplied) on the

wall with the help of the screw grips (supplied). The screws must protrude

slightly from the wall. Align the keyhole slots with the screws fixed on the

wall. Slide the PROTON 103 down on the screws to secure it on the wall.

Or

Lay the PROTON 103 on a table (with the front side facing up).

Connect the Trunk line

2. Remove the cover of the PROTON 103 by pressing on the top panel of the

PROTON 103 as indicated (Figure 5).

3. Using your thumb and index finger, grip and push back the Trunk terminal

(Figure 2).

4. Insert the stripped ends of the two wires into the two terminal openings

(one wire in each opening). Release your grip. Ensure that both wires fit

neatly.

Connect the station lines

5. Using your thumb and index finger, grip and push back the Station

terminal of Station number 2 (Figure 2).

6. Insert the stripped end of each wire of the station cable into each opening/

hole respectively. Release your grip. Ensure that both wires in the cable fit in

neatly.

Repeat the same steps to connect Station number 3 and 4.

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 8/12

7. Match pulse/tone of trunk line and stations. If trunk line is pulse type,

keep all the station phones in pulse mode. Similarly, if trunk line is tone

type, keep all the station phones in tone mode.

Powering the PROTON

8. Check voltage in the mains supply.

9. Insert the 3-pin plug of the mains cable into an electrical outlet supplying

230VAC, 50Hz power.

10. Switch On mains to power the PROTON. The power LED, ‘ON’, will be turned

on when mains switch is operated.

Step 2: Configuring PROTON 103

PROTON is programmed by dialing code sequences for each station and feature

group. The code sequence is typically:

Dial Code-Station Number-Code.

If programming code sequence you dialed is incorrect, you will get an

error tone. Replace the handset to disconnect, enter the correct code

sequence again.

1. Enter Programming Mode

• Lift Handset.

• Dial 19-1234 (default password).

2. Set Feature Access Level

Basic features like Call Transfer, Hold/Toggle, Call Pick Up, Auto Call

Back, are available on all stations. However, to set more advanced

features like Do Not Disturb, Hotline, Conference, etc., you must set the

Feature Access Level for each station.

To set feature access level for Station 2:

• Dial 31-2-0for Basic features.

• Dial 31-2-1 for Basic features, Do Not Disturb, Hotline, Hot Outward

Dialing.

• Dial 31-2-2for Basic features, Do Not Disturb, Hotline, Hot Outward

Dialing, Interrupt Request.

• Dial 31-2-3 for Basic features, Do Not Disturb, Hotline, Hot Outward

Dialing, Interrupt Request, Conference.

• Dial 31-2-4 for Basic features, Do Not Disturb, Hotline, Hot Outward

Dialing, Interrupt Request, Conference, Raid.

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 9/12

Follow the same steps for Station 3 and 4.

3. Set Class of Service Level

To set Class of Service for Station 2:

• Dial 32-2-0to deny Trunk access.

• Dial 32-2-1 to allow dialing of only local numbers.

• Dial 32-2-2to allow dialing of numbers starting with ‘9’

• Dial 32-2-3 to allow STD access.

• Dial 32-2-4 to allow ISD access.

Follow the same steps for Station 3 and 4.

4. Set Hunting Scheme

To set the Hunting Scheme for Station 2:

• Dial 43-2-0to turn Off Hunting.

• Dial 43-2-1 for Round Robin Ring.

• Dial 43-2-2for Delayed Simultaneous Ring.

• Dial 43-2-3 for Immediate Simultaneous Ring.

Default: Round Robin

Follow the same steps for Station 3 and 4.

5. Set Day and Night Mode

To set Day-Night Mode manually:

• Dial 11 to change to Day mode.

• Dial 12to change to Night mode.

To set Auto Day-Night Mode:

• Dial 221 to turn ON.

• Dial 222to turn OFF.

Default: Off

To set a Station as destination for Day/Night Mode:

• Dial 41-2to set Station 2 as destination for Day Mode.

• Dial 42-2to set Station 2 as destination for Night Mode.

Follow the same steps for Station 3 and 4.

6. Exit Programming Mode

• Dial ‘0’

• You will hear the dial tone.

Congratulations! PROTON 103 is now fully operational with its PBX features.

7/27/2019 Proton-103 v1 Quick Start

http://slidepdf.com/reader/full/proton-103-v1-quick-start 10/12

Reinstate Default Setup?

• Dial 19-Password(if not changed, use default 1234).

• Dial 18-Password-get confirmation tone.

• Reconfigure the PROTON 103.

Change Programming Password?

• Dial 21-New Password(max. 4 digits).

Forgot Programming Password?

To restore default password:

• Switch off power supply, plug out the mains cable.

• Remove top cover.

• Change position of mini jumper on the PCB (J5) near the LED

connector to A-B position (Figure 3).

• Connect mains cable, switch on power supply.

• Wait for 3 seconds Do not touch the device!

• Switch off power supply, remove mains cable.

• Restore mini jumper to original position B-C.

• Replace top cover.

• Switch on power supply.

• Enter programming mode by dialing Dial 19-1234.

Inhaltsverzeichnis

Andere Matrix Telefonanlage Handbücher

Matrix

Matrix Visionpro Benutzerhandbuch

Matrix

Matrix Vision Benutzerhandbuch

Matrix

Matrix ETERNITY NE Bedienungsanleitung

Matrix

Matrix ETERNITY Bedienungsanleitung

Matrix

Matrix ETERNITY NE Bedienungsanleitung

Matrix

Matrix Visionpro Bedienungsanleitung

Matrix

Matrix ETERNITY NE Bedienungsanleitung

Matrix

Matrix ETERNITY NE Benutzerhandbuch

Matrix

Matrix ETERNITY Stücklistenhandbuch

Matrix

Matrix ETERNITY ME Bedienungsanleitung

Beliebte Telefonanlage Handbücher anderer Marken

Allo.com

Allo.com Nano 2 Bedienungsanleitung

ZYCOD

ZYCOD ZX50 Bedienungsanleitung

Panasonic

Panasonic KX-TDA100BX Bedienungsanleitung

LV switch

LV switch IPPBX800 Gebrauchsanweisung

Edge-Core

Edge-Core VST3305 Bedienungsanleitung

Panasonic

Panasonic KX-T7625 - Digital Proprietary Speakerphone 24... Bedienungsanleitung

Rauland-Borg

Rauland-Borg Telecenter IV Bedienungsanleitung

Grandstream Networks

Grandstream Networks UCM6208 Bedienungsanleitung

ATCOM

ATCOM IPPBX IP02 Bedienungsanleitung

Panasonic

Panasonic KX-TVS50 - 2 Port Voicemail System Bedienungsanleitung

bintec elmeg

bintec elmeg elmeg hybird 600 Bedienungsanleitung

Panasonic

Panasonic KX-NS300 Bedienungsanleitung

MCK

MCK EXTender PBXgateway Bedienungsanleitung

Panasonic

Panasonic KX-NS300CN Betriebsanleitung

NEC

NEC SL1000 Bedienungsanleitung

Epygi

Epygi Quadro Quadro 2xi Bedienungsanleitung

SMC Networks

SMC Networks TigerVoIP SMCPBX10 Bedienungsanleitung

AGFEO

AGFEO AC 14 analog Bedienungsanleitung