Matrix SATATYA PZCR20ML25CWP Bedienungsanleitung
SATATYA PTZ Dome IP Camera
The Persistent Vision
Safety Instructions
Cautions
Warning
Consignes de sécurité
These instructions are intended to ensure that the user can
use the product correctly to avoid danger or property loss.
•Ensure that the power supply voltage is correct before using the
camera.
•Avoid placing cables too close to magnetic or high voltage
devices, to reduce undesirable image noise.
•Do not touch sensor modules with fingers. For cleaning use
‘clean cloth’ and wipe it gently.
•Do not mount the camera with the lens facing the sun or bright
light to prevent damage to the sensor.
•Do not expose the camera to temperatures below or beyond its
operating temperature.
•Do not mount the camera near a radiator or a heater.
•In the use of the product, you must be in strict compliance with
the electrical safety regulations of the region and nation.
•Do not connect several devices to one power adapter as it may
cause over-heating or fire hazard.
•If smoke, odour or noise rise from the device, turn off the power at
once and unplug the power cable, and contact the nearest service
center.
•To prevent electrical shock, turn off power supply before making
electrical connections.
Précautions
Attention
Ces instructions ont pour but de garantir que l'utilisateur peut Utilisez
le produit correctement pour éviter tout danger ou perte de propriété.
•Vérifiez que la tension d'alimentation est correcte avant d'utiliser
l'appareil photo.
•Évitez de placer des câbles trop près d'une tension magnétique
ou élevée périphériques, pour réduire le bruit d'image indésirable.
•Ne touchez pas les modules de capteur avec les doigts. Pour le
nettoyage, utilisez nettoyer chiffon et essuyez-le doucement.
•Ne montez pas l'appareil photo avec l'objectif dirigé vers le soleil
ou vers lumière pour éviter d'endommager le capteur.
•N'exposez pas l'appareil photo à des températures inférieures ou
supérieures à ses température de fonctionnement.
•Ne montez pas la caméra à proximité d'un radiateur ou d'un
appareil de chauffage.
•Dans l'utilisation du produit, vous devez être en stricte conformité
avec les réglementations de sécurité électrique de la région et de
la nation.
•Ne connectez pas plusieurs périphériques à un seul adaptateur
secteur, provoquer une surchauffe ou un risque d'incendie.
•Si de la fumée, des odeurs ou du bruit émanent de l'appareil,
éteignez-le une fois, débranchez le câble d'alimentation et
contactez le service d'assistance le plus proche centre.
•Pour éviter un choc électrique, éteignez l'alimentation avant de
connections electriques.
What your Package Contains
Know your Camera
Powering the Camera
Accessing via Web Browser
4
Camera Variants
Installation
Accessing Reset Switch and SD card slot
Technical Specification
IP66/67 Protection Accessory Installation
Figure 1
Contents
Please read this guide first for correct installation and retain it for future reference. The
information in this guide is prevailing at the time of publication. However, Matrix Comsec
reserves the right to make changes in product design and specifications without prior
notice.
Copyright
All rights reserved. No part of this document may be copied or reproduced in any form or
by any means without the prior written consent of Matrix Comsec.
Warranty
Limited Warranty. Valid only if primary protection is provided, mains supply is within limit
and protected, and environment conditions maintained within product specifications.
Complete warranty statement is available on our website:
www.matrixvideosurveillance.com
Things you will Need
Wall Mounting
Ceiling Mounting
Adjusting Camera Angle
Know your Camera
1. Cable Assembly
2. Speed Dome Top
3. Camera Lens
4. Ear Flaps
5. Bracket
6. Spring Buckle
7. Bracket Screw
6
8
5
5
11
12
13
14
17
5
20
25
4
1
3
2
4
5
6
7
What your Package Contains
Things you will Need
Camera Variants
The SATATYA PTZ Dome Cameras are Premium 2MP with zoom
focal length cameras. The variants are listed in the table below:
5
•PTZ Dome IP Camera Unit
•Wall Mounting Template
•Wall Mounting Screws with Screw Grip
•Cable Accessories
•Power Adapter
•A Power Drill, Screwdriver Set, Pliers, Wire-cutter, Ladder.
•Necessary Cabling
•A Power Supply with the recommended output voltage of 12V DC.
Use an Adapter to connect the camera to the power outlet.
Type of
Lens
Focal
Length
Zoom
4.6-152mm
Premium
4.8-120mm
6
Recommendations:
1. Use a UL listed power supply unit marked “Class 2” or “LPS” or “PS2” and
rated 12VDC, 2A min.
2. Make sure the wired LAN hub providing Power over the Ethernet (PoE) is in
accordance with IEEE 802-3af, shall be a UL listed device with the output
evaluated as a limited power source as defined in UL60950-1 or PS2 as defined
in UL62368-1.
Installation Instruction
PZCR20ML25CWP
PZCR20ML33CWP
Installation
Installation Methods
•Wall Mount
•Ceiling Mount
Before you start
Please make sure,
•The device in the package is in good condition and all the
assembly parts are included.
•All the related equipments are powered-off before installation.
•The installation surface of the wall-mounted installation bracket
must have the capacity to bear enough weight.
Zoom
The Ceiling Mounting Template and other Ceiling Mounting
accessories like Pedant Pipe will not be provided by Matrix.
Step 1: Select a Location
Select a suitable location for your camera to enable coverage of the
intended surveillance area. The location should preferably be a flat
surface, such as a Wall or a Ceiling.
You can insert SD card in camera to store recordings during network
failover and to upload image or clip as a result of event trigger. For
details refer page 13.
Step 2: Prepare for Installation
•The camera can be powered by the Adapter or PoE switch. In
case, the camera is to be powered using the Adapter, a 5A plug
is needed nearby.
•Provide proper connectivity between camera and recording
location through LAN cable.
•Stick the Mounting Template at the exact location of camera
installation. The location can be ceiling or wall.
•Drill four holes according to the dimensions of the bracket
positioning holes, see Figure 2a.
•Insert the screw grips in the holes you drilled.
•In case of Concealed Wiring, a separate hole has to be drilled in the
center for cable outlet.
•Affix the Mounting Template or plate with Bracket using the screws
on the wall/ ceiling as shown in Figure 2b.
Step 3: Wall Mounting
78
Figure 2a
•The outdoor installation shall be completely sealed and
moisture-proof; the outgoing cable shall be laid close to the
lower edge of the wall mounted installation bracket to avoid rain
entering the interior of the dome camera along the cable.
Figure 2b
Hole for
Concealed Wiring
Step 4: Arranging the Cables
For Concealed Cabling:
•Insert the main-cabling through the center hole and make proper
connection with LAN Cable, see Figure 3a.
For External Cabling:
•Pull the cable out through the cable guide, sideways to the camera,
see Figure 3b.
Figure 3a
Figure 3b
Step 5: Mounting the Dome Body
•Insert the Safety Buckle into the Dome and then hook it onto the
Mounted Bracket as shown in Figure 4.
•Route the cables through the Bracket, see Figure 4.
•Affix the Dome body with the Bracket using the three Bracket
screws(1,2,3). Tighten the screws using the screw driver, as shown in
the figure below.
910
Figure 4
Cable Routing
Spring Buckle
2
1
3
Step 6: Adjusting Camera Angle
Camera angle can be adjusted via PAN Movement and Tilt
Movement, refer to the table below for PAN and Tilt Movement
Range.
11 12
Figure 5
Pedant Pipe to adjust
the height of Camera
PZCR20ML25CWP PZCR20ML33CWP
Parameter Name
PAN Range
PAN Speed
0
360
0 0
Manual: 0.1 to 180 /s;
0
Preset: 240 /s
0 0
Manual: 0.1 to 200 /s;
0
Preset: 240 /s
Tilt Range
Tilt Speed
0 0
-15 to -90 (Auto Flip)
0 0 0
Manual: 0.1 to 120 /s; Preset: 180 /s
Ceiling Mounting
•For Ceiling Mounting follow the same steps as mentioned in Wall
Mounting. Use the Pendant Pipe instead of the Bracket as shown
in Figure 5.
IP66/67 Protection Accessory Installation
1. By default your camera contains the LAN connector fitted by
IP66/67 protection accessory.
2. The IP66/67 protection assembly consist of tail end, middle part,
“IO” ring and LAN connector as shown below.
Tail end Middle
Part “O”ring LAN
Connector
Power Cable
Protection Accessory
Accessing Reset Switch & SD Card Slot
If you forget the IP address or login credentials then the camera can be
reset to factory default settings using the Reset Switch.
•The Reset Switch and SD card compartment lid is located behind the
camera lens as shown in Figure 6.
•To Access the Reset Switch open the lid. Press the Reset Switch for
minimum 5 sec and release the switch to reset the camera to default
settings.
•You can insert the SD card in the slot to store your camera
recordings.
Figure 6
13 14
IP66 Protection Accessory is used in PZCR20ML25CWP Camera,
while IP67 Protection Accessary is used in PZCR20ML33CWP
Camera. However, the installation process for IP66/ IP67 is same as
follows:
Reset Switch/ SD Card
Compartment Lid
6. Insert male RJ45 connector into female connector part. Then
tighten the middle part by rotating in clockwise direction.
Do not remove the “O” ring from its place.
LAN Connector
IP6/67 Accessory
4. Loosen the tail end of the IP66/67 accessory by rotating it in
anticlockwise direction.
Ethernet cable
5. Insert the ethernet cable from behind. Then tighten the “tail end”
by rotating in clockwise direction to its maximum and crimp the
RJ45 connector.
15 16
3. Rotate the middle part of IP66/67 assembly in anticlockwise
direction to detach the IP66/67 accessory from the LAN connector.
Powering the Camera
Connect the Ethernet cable to LAN port and Power cable to the 12V
DC power supply.
Power over Ethernet (PoE)
The IP Camera is PoE compliant, allowing transmission of power and
data via a single Ethernet cable connected to PoE switch.
Connect Audio I/O and Alarm I/O cables if required.The Cable
Assembly description is as follows:
17 18
3. Network Cable Socket present in both variants. It is used to
connect the camera to the computer host or other network
equipment. When connecting the network cable, it is recommended
that the network cable should not be more than 100m long. Also
used when you need to provide power to the Camera using PoE.
4. Audio Input/ Output Cable present in both variants. You can
connect the Audio Input device such as Mike to the Audio Input
cable of the camera. The audio when enabled will be recorded with
the video and will be available at the monitoring location. You may
connect the Audio Output device such as Earphone or Speaker to
the Audio Output cable of the camera. This will generate audio
received from the network.
123 4 5 6
1. DC Power Cable is used only in PZCR20ML25CWP Camera for
power supply.
2. AC Power Cable is used only in PZCR20ML33CWP Camera for
power supply.
Wiring Details
Andere Handbücher für SATATYA PZCR20ML25CWP
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Matrix Sicherheitskamera Handbücher
Matrix
Matrix SATATYA Professional Series Bedienungsanleitung
Matrix
Matrix SATATYA Professional Series Bedienungsanleitung
Matrix
Matrix SATATYA PZCR20ML33CWP Benutzerhandbuch
Matrix
Matrix SATATYA PZCR50ML42CWP Bedienungsanleitung
Matrix
Matrix SATATYA Project Series Bedienungsanleitung
Matrix
Matrix SATATYA PZCR20ML25CWP Benutzerhandbuch
Matrix
Matrix SATATYA PZCR50ML42CWP Benutzerhandbuch
