Mauser MA 1245 Leitfaden
1245MA
1246MA
4153-1-1245-3-2
Taicang 2012-02
© Tribonia Intl.
Adjustment Manual
M
A
U
S
E
R
S
P
E
Z
I
A
L
215400 Taicang, Jiangsu
Index
Contents ..................................................................................Page
13 Adjustment ........................................................................................................................... 5
13.01 Notes on adjustment ....................................................................................................... ...... 5
13.02 Tools, gauges and other accessories for adjusting ............................................................... 5
13.03 Abbreviations ............................................................................................................. ............ 5
13.04 Explanation of the symbols................................................................................................ .... 5
13.05 Adjusting the basic machine ............................................................................................... ... 6
13.05.01 Positioning the feed dog across the direction of sewing ....................................................... 6
13.05.02 Positioning the feed dog in the direction of sewing .............................................................. 7
13.05.03 Height of the bottom feed-dog ......................................................................................... .... 8
13.05.04 Pre-adjusting the needle height ........................................................................................ ..... 9
13.05.05 Centering the needle in the needle hole.............................................................................. 10
13.05.06 Lifting motion of the bottom feed-dog . ............................................................................... 1 1
13.05.07 Driving motion of the bottom and top feeds........................................................................ 12
13.05.08 Hook-to-needle clearance, needle rise, needle height and needle guard ........................... 13
13.05.09 Top-feed stroke ........................................................................................................ ............ 15
13.05.10 Lifting motion of the top feed ........................................................................................ ..... 16
13.05.11 Bobbin-case opener .................................................................................................... ........ 17
13.05.12 Safety clutch .......................................................................................................... .............. 18
13.05.13 Needle thread tension release.......................................................................................... ... 19
13.05.14 Thread check spring .................................................................................................... ......... 20
13.05.15 Thread check spring .................................................................................................... ......... 21
13.05.16 Bobbin winder.......................................................................................................... ............ 22
13.05.17 Presser-foot pressure.................................................................................................. ......... 23
13.06 Adjusting the thread trimmer -900/56 ................................................................................. 24
13.06.01 Pre-adjusting the control cam ......................................................................................... .... 24
13.06.02 Tripping lever......................................................................................................... ............... 25
13.06.03 Pawl .................................................................................................................. .................. 26
13.06.04 Engaging solenoid...................................................................................................... .......... 27
13.06.05 Release trip .......................................................................................................... ............... 28
13.06.06 Engaging lever ......................................................................................................... ............ 29
13.06.07 Linkage rod ........................................................................................................... .............. 30
13.06.08 Final adjustment of the control cam .................................................................................... 31
13.06.09 Catch ................................................................................................................. .................. 33
Index
Contents ..................................................................................Page
13.06.10 Connecting rod (for MA 1246 only) ..................................................................................... 34
13.06.11 Thread-catcher height ................................................................................................. .............35
13.06.12 Knife ................................................................................................................. ................... 36
13.06.13 Thread catcher reverse position ............................................................................................... ..........37
13.06.14 Bobbin-thread clamp spring .................................................................................................... ............38
13.06.15 Tension release bar ............................................................................................................ ..................40
13.07 Parameter settings ........................................................................................................... ... 42
13.07.01 Parameter list......................................................................................................... .............. 42
14 Circuit diagrams................................................................................................................. 43
Adjustment
5
13 Adjustment
Please observe all notes from Chapter 1 Safety of the instruction manual!
In particular care must be taken to see that all protective devices are re tted
properly after adjustment, see Chapter 1.06 Danger warnings of the instruction
manual!
If not otherwise stated, the machine must be disconnected from the electrical
power supply. Danger of injury due to unintentional starting of the machine!
The illustrations in this section show the MA 1245 single-needle machine.
For the MA 1246 two-needle machine, various adjustments must be made
twice, i.e. to the left- and right-hand sewing hooks. This will be pointed out in
the respective sections, whereby it is often possible to apply the mirror image
of the illustrations.
13.01 Notes on adjustment
All following adjustments are based on a fully assembled machine and may only be carried
out by expert staff trained for this purpose.
Machine covers, which have to be removed and replaced to carry out checks and adjust-
ments, are not mentioned in the text.
The order of the following chapters corresponds to the most logical work sequence for
machines which have to be completely adjusted. If only speci c individual work steps are
carried out, both the preceding and following chapters must be observed.
Screws, nuts indicated in brackets ( ) are fastenings for machine parts, which must be
loosened before adjustment and tightened again afterwards.
13.02 Tools, gauges and other accessories for adjusting
Screwdrivers withi blade widths from 2 to 10 mm
Spanners (wrenches) in sizes from 7 to 14 mm
Allen keys from 1.5 to 6 mm
Metal rule (part No. 08-880 218-00)
Needle-rise gauge (part No. 61-111 600-01)
Gauge, (top feed stroke 7 mm) (Part No. 61-111 633-61)
Screw clamp (part No. 61-111 600-35)
13.03 Abbreviations
t.d.c. = top dead centre
b.d.c. = bottom dead centre
13.04 Explanation of the symbols
In this adjustment manual, symbols emphasize operations to be carried out or important in-
formation. The symbols used have the following meaning:
Note, information
Service, repair, adjustment, maintenance
(work to be carried out by quali ed staff only)
Adjustment
6
13.05 Adjusting the basic machine
13.05.01 Positioning the feed dog across the direction of sewing
Requirement
The bottom feed dog must be the same distance from the left and right side of the need-
le-plate cutout.
Loosen screws 1 and 2.
Laterally align rock shaft 3 in accordance with the requirement.
Now tighten screws 1.
The at sides of pins 4 must be opposite the at sides of screws 1 and rock
shaft 3 must exhibit neither play nor stiffness.
Screws 2 remain loose for the following adjustments..
Fig. 13 - 01
41
2
31
4
Adjustment
7
13.05.02 Positioning the feed dog in the direction of sewing
Requirement
With the longest stitch set, the bottom feed dog must have the same clearance the front
and the back with respect to the needle-plate cutout when feeding both forwards and
backwards.
Set the longest stitch.
Adjust rock shaft 1 in accordance with the requirement and tighten screws 2.
Fig. 13 - 02
2
1
Adjustment
8
13.05.03 Height of the bottom feed-dog
Requirement
With the stitch length set at "0", the bottom feed dog must protrude over the needle plate
as high as the teeth when at TDC.
Set stitch length "0".
Bring the bottom feed dog to its TDC by turning the handwheel.
Adjust feed dog carrier 1 (screws 2) in accordance with the requirement.
If required, the feed dog height can be reduced a little on machines without a
bottom feed lifting phase (without P).
Fig. 13 - 03
21
Adjustment
9
13.05.04 Pre-adjusting the needle height
Requirement
With the needle bar at BDC, the distance between the needle bar and the needle plate
must be 15 mm.
Move needle bar 1 (screw 2) in accordance with the requirement without moving it
laterally.
Fig. 13 - 04
2
1
Adjustment
10
13.05.05 Centering the needle in the needle hole
Requirement
With the stitch length set at "0", the needle must enter the needle hole exactly in the
middle.
Unscrew vibrating presser 1 and presser foot 2.
Set stitch length "0"and bring the needle bar to its TDC.
Insert a new needle. Loosen screws 3, 4, 5 and 6.
Position the needle directly over the bottom feed dog by turning the handwheel.
Move needle bar frame 7 in accordance with the requirement.
Tighten screws 3, 4 and 5.
Position stop 8 so that it is touching needle bar frame 7 and tighten screw 6.
The movement of needle bar frame 7 in guide 9 and of the top feed drive bars
must not be stiff.
Fig. 13 - 05
2
3
1
9
5
6
7
4
8
Andere Handbücher für MA 1245
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Mauser Nähmaschine Handbücher
Mauser
Mauser MO5100 Stücklistenhandbuch
Mauser
Mauser MA 2081 Bedienungsanleitung
Mauser
Mauser MO6101 Stücklistenhandbuch
Mauser
Mauser MA 335 Bedienungsanleitung
Mauser
Mauser MA 1245 Bedienungsanleitung
Mauser
Mauser MA 2545 Bedienungsanleitung
Mauser
Mauser MA 335 Bedienungsanleitung
Mauser
Mauser MI5530 Stücklistenhandbuch
Mauser
Mauser MH1341 Stücklistenhandbuch
Mauser
Mauser MO5101 Bedienungsanleitung
