Max CN238D Betriebsanleitung

CN238D(CE)

PNEUMATIC COIL NAILER

DRUCKLUFT-COIL-NAGLER

CLOUEUSES PNEUMATIQUES

A BOBINES

SPARACHIODI AD ARIA COMPRESSA

CON CARICAMENTO A ROTOLO

CLAVADORAS NEUMATICAS PARA

ROLLOS DE CLAVOS

OPERATING and MAINTENANCE MANUAL

BETRIEBSANLEITUNG

MANUEL D’UTILISATION et D’ENTRETIEN

MANUALE DI FUNZIONAMENTO E MANUTENZIONE

MANUAL DE OPERACIONES Y MANTENIMIENTO

BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING AND

INSTRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

LESEN SIE VOR INBETRIEBNAHME DES GERÄTES DIE GEBRAUCHS- UND SICHERHEITS-

HINWEISE. BITTE BEWAHREN SIE DIE GEBRAUCHS- UND SICHERHEITSHINWEISE AUF,

DAMIT SIE AUCH SPÄTER EINGESEHEN WERDEN KÖNNEN.

AVANT D’UTILISER CET OUTIL, LIRE CE MANUEL ET LES CONSIGNES DE SECURITE

AFIN DE GARANTIR UN FONCTIONNEMENT SUR.

CONSERVER CE MANUEL EN LIEU SUR AVEC L’OUTIL AFIN DE POUVOIR LE CONSULTER

ULTERIEUREMENT.

PRIMA DI USARE QUESTA MACCHINA, STUDIARE IL MANUALE PER PRENDERE ATTO

DEGLI AVVERTIMENTI E DELLE ISTRUZIONIPER LA SICUREZZA.

TENERE QUESTE ISTRUZIONI INSIEME ALLO STRUMENTO PER CONSULTAZIONI FUTURE

PARA EVITAR GRAVES DAÑOS PERSONALES O EN LA PROPIEDAD.

ANTES DE EMPLEAR LA HERRAMIENTA, LEER CON ATENCIÓN Y COMPRENDER LOS

SIGUIENTES INSTRUCCIONES DE SEGURIDAD.

WARNING:

ACHTUNG!

AVERTISSEMENT:

ATTENZIONE:

ATENCIÓN:

Original Language English

INDEX INHALTSVERZEICHNIS INDEX INDICE INDICE

ENGLISH Page 3 to 13 Page

DEUTSCH Page 15 to 25 Page

FRANÇAIS Page 27 to 37 Page

ITALIANO Page 39 to 49 Page

ESPAÑOL Page 51 to 61 Page

DEFINITIONS OF SIGNAL WORDS

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTE: Emphasizes essential information.

DEFINITIONEN DER HINWEISBEZEICHNUNGEN

ACHTUNG! Zeigt eine eventuell gefährliche Situation an, die den Tod oder schwere Verletzungen zur Folge haben

könnte, wenn sie nicht vermieden wird.

VORSICHT! Zeigt eine eventuell gefährliche Situation an, die leichte oder mittelschwere Verletzungen zur Folge

haben könnte, wenn sie nicht vermieden wird.

HINWEIS: Hebt wichtige Informationen hervor.

DÉFINITIONS DES DIFFÉRENTS DEGRÉS D’ AVERTISSEMENTS

AVERTISSEMENT Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée, pourrait provoquer la

mort ou des blessure sérieuses.

ATTENTION Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée, pourrait provoquer

des blessures légères à moyennement sérieuses.

REMARQUE Souligne des informations importantes.

DEFINIZIONE DELLE INDICAZIONI DI AVVERTIMENTO

ATTENZIONE: Indica l’eventualità che possa verificarsi una situazione pericolosa, la quale se non viene evitata, può

risultare letale o provocare gravi lesioni.

AVVERTENZA: Indica l’eventualità che possa verificarsi una situazione pericolosa, la quale se non viene evitata, può

provocare lesioni di lieve o media entità.

NOTA: Evidenzia informazioni importanti.

DEFINICIÓN DE LAS INDICACIONES DE ADVERTENCIA

¡ATENCIÓN! Indica una situación potencialmente peligrosa que podría causar la muerte o graves lesiones si no se

evita.

¡PRECAUCIÓN! Indica una situación potencialmente peligrosa que podría causar lesiones menos graves o leves si no

se evita.

NOTA: Resalta informaciones importantes.

ENGLISH

CN238D(CE)

PNEUMATIC COIL NAILER

INDEX

1. SAFETY INSTRUCTIONS

……………

2. SPECIFICATIONS &

TECHNICAL DATA

……………………

3. AIR SUPPLY AND CONNECTIONS

…

4. INSTRUCTIONS FOR OPERATION

…

5. MAINTAIN FOR PERFORMANCE

…

6. STORING

……………………………

7. TROUBLESHOOTING/REPAIRS

……

OPERATING and MAINTENANCE MANUAL

BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING

AND INSTRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

WARNING:

1. SAFETY INSTRUCTIONS

PRECAUTIONS ON USING THE TOOL

1. WEAR SAFETY GLASSES OR GOGGLES

Danger to the eyes always exists due to the possibility of dust being blown up by the exhausted air

or of a fastener flying up due to the improper handling of the tool. For these reasons, safety glasses

or goggles shall always be worn when operating the tool.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment

must conform to the requirements of the American National Standards Institute, ANSI Z87.1 (Council

Directive 89/686/EEC of 21 DEC. 1989) and provide both frontal and side protection.

The employer is responsible to enforce the use of eye protection equipment by the tool operator

and all other personnel in the work area.

NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

2. EAR PROTECTION MAY BE REQUIRED IN SOME ENVIRONMENTS

As the working condition may include exposure to high noise levels which can lead to hearing

damage, the employer and user should ensure that any necessary hearing protection is provided and

used by the operator and others in the work area.

3. DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR

The tool is designed to operate on compressed air. Do not operate the tool on any other highpressure

gas, combustible gases (e.g., oxygen, acetylene, etc.) since there is the danger of an explosion. For

this reason, absolutely do not use anything other than an air compressor to operate the tool.

4. OPERATE WITHIN THE PROPER AIR PRESSURE RANGE

The tool is designed to operate within an air pressure range of 4 to 8 bar (60 to 120 p.s.i.).

The pressure should be adjusted to the type of the work being fastened. The tool shall never be

operated when the operating pressure exceeds 8 bar (120 p.s.i.).

Never connect the tool to air pressure which potentially exceeds 14 bar (200 p.s.i.) as the tool can

burst.

5. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE

Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). Volatile fumes from

these substances could be drawn into the compressor and compressed together with the air and this

could result in an explosion.

6. DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting

is used, the tool can remain charged with air after disconnecting and thus will be able to drive a

fastener even after the air line is disconnected, possibly causing injury.

7. DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE TOOL IS NOT

IN USE

Always disconnect the air supply from the tool and empty the magazine when operation has been

completed or suspended, when unattended, moving to a different work area, adjusting,

disassembling, or repairing the tool, and when clearing a jammed fastener.

WARNING:

TO AVOID SEVERE PERSONAL INJURY OR PROPERTY DAMAGE

BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING

“SAFETY INSTRUCTIONS”. FAILURE TO FOLLOW WARNINGS COULD RESULT IN DEATH OR

SERIOUS INJURY.

120

8. INSPECT SCREW TIGHTNESS

Loose or improperly installed screws or bolts cause accidents and tool damage when the tool is put

into operation. Inspect to confirm that all screws and bolts are tight and properly installed prior to

operating the tool.

9. DO NOT TOUCH THE TRIGGER UNLESS YOU INTEND TO DRIVE A FASTENER

Whenever the air supply is connected to the tool, never touch the trigger unless you intend to drive

a fastener into the work. It is dangerous to walk around carrying the tool with the trigger pulled, and

this and similar actions should be avoided.

10. NEVER POINT THE DISCHARGE OUTLET TOWARD YOURSELF AND OTHER PERSONNEL

If the discharge outlet is pointed toward people, serious accidents may be caused when misfiring.

Be sure the discharge outlet is not pointed toward people when connecting and disconnecting the

hose, loading and unloading the fasteners or similar operations.

11. USE SPECIFIED FASTENERS (SEE PAGE 7)

The use of fasteners other than specified fasteners will cause the tool malfunction. Be sure to use

only specified fasteners when operating the tool.

12. PLACE THE DISCHARGE OUTLET ON THE WORK SURFACE PROPERLY

Failure to place the discharge outlet of the nose in a proper manner can result in a fastener flying

up and is extremely dangerous.

13. KEEP HANDS AND BODY AWAY FROM THE DISCHARGE OUTLET

When loading and using the tool, never place a hand or any part of body in fastener discharge area

of the tool. It is very dangerous to hit the hands or body by mistake.

14. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE AND CORNER OF THE WORK AND THIN

MATE RIAL

The workpiece is likely to split and the fastener could fly free and hit someone.

15. DO NOT DRIVE FASTENERS ON TOP OF OTHER FASTENERS

Driving fasteners of the top of other fasteners may cause deflection fasteners which could cause

injury.

16. REMOVING THE FASTENERS AFTER COMPLETING OPERATION

If fasteners are left in the magazine after the completion of operation, there is the danger of a serious

accident occurring prior to the resumption of operation, should the tool be handled carelessly, or

when connecting the air fitting. For this reason, always remove all fasteners remaining in the

magazine after completion of the operation.

17. CHECK OPERATION OF THE CONTACT TRIP MECHANISM FREQUENTLY IN CASE OF

USING A CONTACT TRIP TYPE TOOL

Do not use the tool if the trip is not working correctly as accidental driving of a fastener may result.

Do not interfere with the proper operation of the contact trip mechanism.

18. WHEN USING THE TOOL OUTSIDE OR ELEVATED PLACE

When fastening roofs or similar slanted surface, start fastening at the lower part and gradually work

your way up. Fastening backward is dangerous as you may loose your foot place.

Secure the hose at a point close to the area you are going to drive fasteners. Accidents may be

caused due to the hose being pulled inadvertently or getting caught.

19. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL CONTROLS (e.g., TRIGGER, CONTACT

ARM) IS INOPERABLE, DISCONNECTED, ALTERED OR NOT WOKING PROPERLY

20. NEVER ACTUATE THE TOOL INTO FREE SPACE

This will avoid any hazard caused by free flying fasteners and excessive strain of the tool.

21. ALWAYS ASSUME THAT THE TOOL CONTAINS FASTENERS

22. RESPECT THE TOOL AS A WORKING IMPLEMENT

23. NO HORSEPLAY

24. NEVER LOAD THE TOOL WITH FASTENERS WHEN ANY ONE OF THE OPERATING CONTROLS

(e.g., TRIGGER, CONTACT ARM) IS ACTIVATED

OBSERVE THE FOLLOWING GENERAL CAUTION IN ADDITION TO

THE OTHER WARNINGS CONTAINED IN THIS MANUAL

•

Do not use the tool as a hammer.

•

Always carry the tool by the handle, never carry the tool by the air hose.

•

The tool must be used only for the purpose it was designed.

•

Never remove, tamper with the operating controls (e.g., TRIGGER, CONTACT ARM)

•

Keep the tool in a dry place out of reach of children when not in use.

•

Do not use the tool without Safety Warning label.

•

Do not modify the tool from original design or function without approval by MAX CO., LTD.

2. SPECIFICATIONS AND TECHNICAL DATA

1. NAME OF PARTS

2. TOOL SPECIFICATIONS

HEIGHT 249 mm (9-7/8˝)

WIDTH 106 mm (4-3/16˝)

LENGTH 217 mm (8-1/2˝)

WEIGHT 1.2 kg (2.6 lbs.)

RECOMMENDED

4 to 8 bar (60 to 120 p.s.i.)

OPERATING PRESSURE

LOADING CAPACITY 200 Nails

AIR CONSUMPTION 0.5Rat 6 bar (90 p.s.i.)

operating pressure

⑧⑥⑨⑦

②

①

④

③⑤

Frame

Cylinder Cap

Contact Arm

Nose

Magazine

Trigger

Grip

Exhaust

Trigger Lock Dial

3. FASTENER SPECIFICATIONS

NAIL LENGTH PLASTIC SHEET COLLATED

17 to 38 mm (11/16˝ to 1-1/2˝)

SHANK DIAMETER

φ1.47 to φ2.0 mm (.058˝ to .079˝)

SHANK TYPE Smooth, Ring, Screw

HEAD DIAMETER

φ3.1 to φ5.0 mm (.122˝ to .197˝)

TOOL AIR FITTINGS:

This tool uses a 6 mm (1/4˝) N.P.T. male plug. The inside diameter should be 7 mm (.28˝) or larger. The fitting must be capable of

discharging tool air pressure when disconnected from the air supply.

RECOMMENDED OPERATING PRESSURE:

4 to 8 bar (60 to 120 p.s.i.). Select the operating air pressure within this range for best fastener performance.

DO NOT EXCEED 8 bar (120 p.s.i.).

4. TECHNICAL DATA

NOISE

A-weighted single-event ------ LWA, 1s, d 88.7 dB

sound power level

A-weighted single-event ------ LpA, 1s, d 81.1 dB

emission sound pressure

level at work station

These values are determined and documented in accordance to EN12549:1999+A1:2008.

NOTE: These values are tool-related characteristic values and do not represent the noise generation at the point of use. Noise

at the point of use will for example depend on the working environment, the workpiece, the workpiece support, and the number

of driving operations. In addition, reference should be made to noise reduction measures.

NOTE: Workplace design can also serve to reduce noise levels, for example placing workpieces on sound-damping supports

(see also ISO11690-1).

VIBRATION

Vibration characteristic value ＝3.09 m/s

These values are determined and documented in accordance to ISO 28927-13

NOTE: The vibration emission value above is a tool-related characteristic value and does not represent the influence to the

hand-arm-system when using the tool. Any influence to the hand-arm-system when using the tool will for example depend on

the gripping force, the contact pressure force, the working direction, the adjustment of energy supply, the workpiece, the

workpiece support.

5. APPLICATIONS

＊General constuction works

＊Furniture assembly including drawer assembly, case back nailing

＊Cabinet assembly

＊Interior and exterior triming

＊Flooring

WARNING:

3. AIR SUPPLY AND CONNECTIONS

Read section titled “SAFETY INSTRUCTIONS”.

DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR

The tool is designed to operate on compressed air. Do not operate the tool on any other highpressure

gas, combustible gases (e.g., oxygen, acetylene, etc.) since there is the danger of an explosion. For this

reason, absolutely do not use anything other than an air compressor to operate the tool.

OPERATE WITHIN THE PROPER AIR PRESSURE RANGE

The tool designed to operate within an air pressure range of 4 to 8 bar (60 to 120 p.s.i.).

The pressure should be adjusted to the type of the work being fastened. The tool shall never be

operated when the operating pressure exceeds 8 bar (120 p.s.i.).

DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE

Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). Volatile fumes from

these substances could be drawn into the compressor and compressed together with the air and this

could result in an explosion.

DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is

used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener

even after the air line is disconnected, possibly causing injury.

DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE TOOL IS NOT IN USE

Always disconnect the air supply from the tool and empty the magazine when operation has been

completed or suspended, when unattended, moving to a different work area, adjusting, disassembling,

or repairing the tool, and when clearing a jammed fastener.

FITTINGS: Install a male plug on the tool which is free flowing and which will release

air pressure from the tool when disconnected from the supply source.

HOSES: Hose has a min. ID of 6 mm (1/4˝) and max. length of no more than 5

meters (17´).

The supply hose should contain a fitting that will provide “quick disconnecting” from

the male plug on the tool.

SUPPLY SOURCE: Use only clean regulated compressed air as a power source for

the tool.

3-PIECE AIRSET (Air filter, Regulator, Oiler):

Refer to TOOL SPECIFICATIONS for setting the correct operating pressure for the

tool.

NOTE:

A filter will help to get the best performance and minimum wear from the tool because dirt and water in

the air supply are major causes of wear in the tool.

Frequent, but not excessive, lubrication is required for the best performance. Oil added thru the air line

connection will lubricate the internal parts.

120

Air compressor Air filter

Air hose

Oiler

Used at 4 to 8 bar (60 to 120 p.s.i.)

Regulator

[AIR SUPPLY & CONNECTIONS]

3-piece airset

120

WARNING:

4. INSTRUCTIONS FOR OPERATION

Read section titled “SAFETY INSTRUCTIONS”.

1. BEFORE OPERATION

Wear Safety Glasses or Goggles.

Do not connect the air supply.

Inspect screw tightness.

Check operation of the contact arm & trigger if moving smoothly.

Connect the air supply.

Check the air-leakage. (The Tool must not have the air-leakage.)

Hold the Tool with finger-off the trigger, then push the contact arm against the work-piece. (The tool

must not operate.)

Hold the Tool with contact arm free from work-piece and pull the trigger. (The Tool must not operate.)

Disconnect the air supply.

2. OPERATION

Wear safety glasses or goggles danger to the eyes always exists due to the possibility of dust being

blown up by the exhausted air or of a fastener flying up due to the improper handling of the tool. For

these reasons, safety glasses or goggles shall always be worn when operating the tool.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment

must conform to the requirements of the American National Standards Institute, ANSI Z87.1 (Council

Directive 89/686/EEC of 21 DEC. 1989) and provide both frontal and side protection.

The employer is responsible to enforce the use of eye protection equipment by the tool operator and all

other personnel in the work area.

NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

Keep hands and body away from the discharge outlet when driving the fasteners because of dangerous

of hitting the hands or body by mistake.

NAIL LOADING

Open the magazine:

Hold door and door latch by fingers and pull up door latch. Swing door open. Swing

magazine cover open.

When you want to use 17-19 mm nails, attach a nail support to the magazine.

Door latch

Magazine

Nail support

Door

Nail loading:

Place a coil of nails over the post in the magazine. Uncoil enough nails to reach the

feed pawl, and place the second nail between the teeth on the feed pawl. The nail

heads fit in slot on nose.

Swing cover closed.

Close the door.

Check that latch engages. (If it does not engage, check that the nail heads are in the

slot on the nose).

※It is also possible to close the door first, followed by the cover.

TEST OPERATION

Adjust the air pressure at 5 bar (70 p.s.i.) and connect the air supply.

Without touching the trigger, depress the contact arm against the work-piece.

Pull the trigger. (The tool must fire the fastener.)

With the tool off the work-piece, pull the trigger.

Then depress the contact arm against the work-piece.

(The tool must fire the fastener.)

Adjust the air pressure as much as the lowest possible according to the diameters and length of

fastener and the hardness of work-piece.

Feed pawl

Nail

MODEL IDENTIFICATION

CONTACT TRIP

The common operating procedure on “Contact Trip” tools is for the operator to contact the work to

actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work

is contacted. This will allow rapid fastener placement on many jobs, such as sheathing, decking and

pallet assembly.

All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip,

and if unintentionally allowed to recontact the work surface with the trigger still actuated (finger still

holding trigger pulled) an unwanted second fastener will be driven.

CONTACT TRIP WITH ANTI-DOUBLE FIRE MECHANISM

(US patent 5597106, UK patent 2286790)

Identified by RED TRIGGER.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Max Nagelpistole Handbücher

Max

Max CN80 Betriebsanleitung

Max

Max SuperSider CN565S2(CE) Betriebsanleitung

Max

Max PowerLite HN65 Bedienungsanleitung

Max

Max SuperLocator SN438J Bedienungsanleitung

Max

Max SuperFramer SN883RH2 Betriebsanleitung

Max

Max PowerLite HA65Q/15-11 Bedienungsanleitung

Max

Max NF201/18-35 Betriebsanleitung

Max

Max NF255SF-ST Betriebsanleitung

Max

Max NF665/15 Betriebsanleitung

Max

Max GS732C LT Betriebsanleitung

Max

Max SN890CH/34 Betriebsanleitung

Max

Max HN50 Betriebsanleitung

Max

Max NF255FA/18 Bedienungsanleitung

Max

Max SN890CH/34 Betriebsanleitung

Max

Max PowerLite HA55SF2/18 Bedienungsanleitung

Max

Max CN450R Betriebsanleitung

Max

Max SN890CH2(CE) Installations- und Betriebshandbuch

Max

Max SuperRoofer CN445R2 Betriebsanleitung

Max

Max SN883-90CH/34(CE) Betriebsanleitung

Max

Max SuperSider CN565S2 Betriebsanleitung

Max

Max HA55SF-ST Betriebsanleitung

Max

Max GS683RH-EX Betriebsanleitung

Max

Max NF235F/18 Betriebsanleitung

Max

Max SN883RH Betriebsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung