Maxcess FIFE DP-20 PLUS Bedienungsanleitung

DP-20PLUS

WEBGUIDECONTROLLER

QUICK START GUIDE

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 2 of 10 Figure Sheet XXX

prior written consent of Maxcess International.

The information provided in this Document is subject to change without notice.

We have compiled this Document with the greatest possible care and attention; however, the

possibility of error cannot be completely excluded. Maxcess International accepts no legal liability for

incorrect information given and the consequences arising there from.

DP-20 PLUS 
Quick Start Guide 
 
 
2021 Maxcess International 3 of 10 Figure Sheet XXX 
Table of Contents 
 
1FEATURES 4 
1.1 DP-20 Plus General Information ........................................................................ 4 
1.2 Display Overview ............................................................................................... 4 
1.3 Function of the Operator Level Keys .................................................................. 5 
2OPERATION 6 
2.1 Initial System Setup ........................................................................................... 6 
2.2 Auto Setup Configuration .................................................................................. 7 
2.3 Manual Configuration (Optional) ....................................................................... 8 
3CABLE CONNECTION DIAGRAMS 9 
4SERVICE 10 
 
List of Figures 
Figure 1 - DP-20 PLUS Display....................................................................................................... 4 
Figure 2 –Edge Guiding ................................................................................................................. 9 
Figure 3 –Center Guiding .............................................................................................................. 9 
 
 
 

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 4 of 10 Figure Sheet XXX

1Features

1.1 DP-20 Plus General Information

The instructions contained in this Quick Start Guide are written to support operation of the DP-20 PLUS

Web Guide Controller User Manual, Figure Sheet 2-320.

1.2 Display Overview

The DP-20 PLUS display is divided into 4 rows of information. A brief description is listed below.

Refer to Figure 1 (shown in operational mode) for the LCD display and keypad button locations.

1) The first line contains the Menu number (1A). May also indicate password protection and

Digital Input/Output (I/O).

2) The second line of the display shows the current Operation Mode (Automatic) or Setup Menu

selected.

3) The third line indicates Edge Left (shown), Edge Right, or Edge Center sensor mode; along with

displaying a bargraph indicating the signal level of the currently selected sensor mode.

4) The fourth line can show the Guide Point value (shown), ASC Control, and ASC Limits

(dependent on menu selection).

Figure 1 - DP-20 PLUS Display

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 5 of 10 Figure Sheet XXX

1.3 Function of the Operator Level Keys

AUTOMATIC - This key initiates the Automatic mode. Correction is

applied to the web by moving the guide in response to the output of the

sensor(s) selected.

SERVO-CENTER - This key initiates the Servo-Center mode. The guide

is centered in its travel in response to the output of the Servo-Center

transducer (if installed).

MANUAL - This key initiates the Manual mode. No correction is applied

to the guide. This key is also used to abort changes made in the Setup

Menus and to exit the Setup Menus.

SENSOR - This key is used to select the sensor(s) for monitoring the web

position when the system is in Automatic mode. Sensor selection is

allowed in Manual and Servo-Center modes only.

SETUP - This key is used to enter the Setup Menus to configure and

adjust the guiding system.

- ARROW - This key is used to jog the guide. The direction of guide

movement is configurable. This key is also used during setups to scroll

through the setup menus and to adjust setup parameters.

ENTER - This key is not used at the Operator Level. It is used while in

the Setup Menus to enter the selected menu and to store modified

parameters.

+ ARROW - This key is used to jog the guide. The direction of guide

movement is configurable. This key is also used during setup to scroll

through the setup menus and to adjust setup parameters.

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 6 of 10 Figure Sheet XXX

2Operation

Connect the system according to the System Block Diagram (Figures 2 and 3) and DP-20 PLUS

Installation Instructions, Figure Sheet 1-939 (included in package).

2.1 Initial System Setup

1) Apply the proper power to the system. See Installation Instructions Figure Sheet 1-939.

2) Verify the system is in Manual Mode by pressing the MANUAL key.

NOTE: If Servo Center option is not available in the next step, go to step #6

3) Switch system to Servo Center Mode by pressing the SERVO-CENTER key.

NOTE: If the guide moves to the center of its stroke press the MANUAL key

to return system to Manual Mode and go to step #7

4) If the guide moves to one side, then change the Servo Center Polarity as follows:

•Press the MANUAL key to change the system operating mode back to Manual Mode.

•Press the SETUP key to enter the Setup menus.

•Select “BASIC” Menu then press ENTER.

•Use the ARROW keys to select “→ Polarity” then press ENTER.

•The current polarity is listed. Press ENTER to allow adjustment of the polarity.

•Use the ARROW keys to change the polarity.

•Press ENTER to save.

5) Move the actuator to the center of its stroke by pressing the left and right arrows.

6) Thread the web/strip through the system and pull proper tension, if possible.

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 7 of 10 Figure Sheet XXX

7) Perform “Sensor Calibration” on the sensor(s) that will provide position feedback for this

web/strip. If two sensors are being used in a center-guiding application they must be

calibrated independently:

•Press the SETUP key to enter the Setup menus.

•Select “BASIC” Menu then press ENTER.

•Use the ARROW keys to select “CALIBRATION” then press ENTER.

•Select the sensor to be calibrated, then press ENTER.

NOTE: Follow the instructions displayed on the LCD Display. Be sure to use the actual

web to be guided (not a sample), to calibrate sensors.

NOTE: If Manual Configuration is desired, go to section 2.3.

2.2 Auto Setup Configuration

1) Place the web/strip in the proper position and then position the sensor(s) to align the center of

the sensor(s) bandwidth with the web/strip to be guided.

2) Perform “Auto Setup” to automatically determine the proper polarity and gain for the system:

•Press the SETUP key to enter the Setup menus.

•Select “BASIC” Menu then press ENTER.

•Use the ARROW keys to select “AUTO SETUP” then press ENTER.

•Press ENTER to begin the Auto Setup. Follow instructions displayed on the LCD Display.

3) Switch the system to Automatic Mode by pressing the AUTO key. This initiates the guiding

function of the system.

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 8 of 10 Figure Sheet XXX

2.3 Manual Configuration (Optional)

1) To manually change the Polarity:

•Press the SETUP key to enter the Setup menus.

•Select “BASIC” Menu then press ENTER.

•Use the ARROW keys to select “GUIDE POLARITY” then press ENTER.

•The current polarity is listed. Press ENTER to allow adjustment of the polarity.

•Use the ARROW keys to change the polarity.

•Press ENTER to save.

2) To manually change the System Gain:

•Press the SETUP key to enter the Setup menus.

•Select “BASIC” Menu then press ENTER.

•Use the ARROW keys to select “GAIN” then press ENTER.

•Press ENTER to allow adjustment of the Gain.

•The current gain is listed. Use the ARROW keys to change the Gain.

•Press ENTER to save.

3) To manually change the Guidepoint:

•Press the SETUP key to enter the Setup menus.

•Select “BASIC” Menu then press ENTER.

•Use the ARROW keys to select “GUIDEPOINT” then press ENTER.

•Press ENTER to allow adjustment of the Guidepoint.

•The current gain is listed. Use the ARROW keys to change the Gain.

•Press ENTER to save.

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 9 of 10 Figure Sheet XXX

3Cable Connection Diagrams

Figure 2 –Edge Guiding Setup

Figure 3 –Center Guiding Setup

DRIVE 1 SENSOR

AND SENSOR CABLE

1 A

AUTOM ATI C

× -ãããããÜÜ ÜÜÜ +

DRIVE 1 SENSORS

AND SENSOR CABLES

AUTOMATIC

× -ãããããÜÜÜÜÜ+

Sensor and Sensor Cable

Sensors and Sensor Cables

DP-20 PLUS

Quick Start Guide

2021 Maxcess International 10 of 10 Figure Sheet XXX

4Service

If you have any questions about one of our products or need to speak with a Customer Service

representative, please use the contact information below.

Andere Handbücher für FIFE DP-20 PLUS

Inhaltsverzeichnis

Andere Maxcess Controller Handbücher

Maxcess

Maxcess H6630EM Bedienungsanleitung

Maxcess

Maxcess MAGPOWR CYGNUS-S3 Series Bedienungsanleitung

Maxcess

Maxcess GMA-BL-1-1 Handbuch

Maxcess

Maxcess MAGPOWR DFC-90 Bedienungsanleitung

Maxcess

Maxcess D-MAXE Bedienungsanleitung

Maxcess

Maxcess Fife GMA-BL Gebrauchsanweisung

Maxcess

Maxcess MAGPOWR DLCA NET-S1 Bedienungsanleitung

Maxcess

Maxcess Magpowr IPT Bedienungsanleitung

Maxcess

Maxcess FIFE D-MAXE 1 Bedienungsanleitung

Maxcess

Maxcess MAGPOWR Spyder-Plus-S1 Bedienungsanleitung

Maxcess

Maxcess MAGPOWR HEB250 Montage- und Bedienungsanleitung

Maxcess

Maxcess MAGPOWR Spyder-Plus Bedienungsanleitung

Maxcess

Maxcess Fife GMA-BL Bedienungsanleitung

Maxcess

Maxcess FIFE DP-20 PLUS Bedienungsanleitung

Maxcess

Maxcess Fife Polaris DP-20 Bedienungsanleitung

Maxcess

Maxcess SE-46C Kurzanleitung

Maxcess

Maxcess Spyder Bedienungsanleitung

Maxcess

Maxcess Fife Polaris DP-20 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung