Maxcess Spyder Bedienungsanleitung

Spyder™ Firmware Update

Instruction Manual

Spyder™and Spyder-Plus™

MI 850A324 C

MAGPOWR TENSION CONTROL

www.maxcessintl.com

Spyder Firmware Update

MI 850A324 1 C

Page 2

All of the information herein is the exclusive proprietary property of Maxcess International and is disclosed with the

understanding that it will be retained in confidence and will neither be duplicated nor copied in whole or in part nor

be used for any purpose other than for which disclosed.

Periodically there will be updates to this manual. The latest version is available at www.maxcessintl.com or by

calling your regional office. See back page for phone numbers.

TABLE OF CONTENTS

Section Description Page

1.0 Introduction 3

2.0 Hardware Connections 3

3.0 Programming the Spyder from a Local Computer 3

3.1 Installation of the FTP Server Software 3

3.2 Running the FTP Server Software 4

3.3 Configuring the Network Connections 4

3.4 Programming the Spyder 5

4.0 Problems 6

5.0 Spyder Reset Functions 7

5.1 Automatic Contrast Adjust 7

5.2 Reset All Parameters Except Calibrations to Defaults 7

5.3 Reset All Parameters to Defaults (Including Calibrations) 7

5.4 Download Software 7

Figures:

Figure 1. FTP Server Screen Shot 3

Figure 2. Local Area Connections 4

Figure 3. TCP/IP Properties 4

www.maxcessintl.com

Spyder Firmware Update

MI 850A324 1 C

Page 3

1. INTRODUCTION

The MAGPOWR Model Spyder may have the firmware upgraded by connecting the Spyder to a local FTP server

running on a laptop or other local computer.

2. HARDWARE CONNECTIONS

Connect the Spyder to a computer or local network using a CAT5 Ethernet cable.

3. PROGRAMMING THE SPYDER FROM A LOCAL COMPUTER

3.1. INSTALLATION OF THE FTP SERVER SOFTWARE

Insert the CD containing the FTP Server software. The setup program should automatically start. If the setup

program does not start or you received the setup program in an e-mail, execute the file FtpServerSetup.exe.

The setup program will ask for a Program Group and if you want a desktop shortcut. Leave these at the defaults or

make a choice and press Next.

The setup program will ask if you want to install the program in the default directory or a directory of your choice.

Leave this at the default or make a choice and press Next.

Confirm your settings and press Next.

Press Finish.

The FTP Server should now be running. There should be a green box in the lower left corner of the FTP server

program showing the server is running, see figure 1, and there should be a flashing "FTP" icon in the system tray of

your computer screen (lower right hand corner).

Figure 1. FTP Server Screen Shot

The FTP Server Software and the latest Spyder program have been installed on the computer. The Spyder

software is contained in the \ftp\ProductSoftware\ sub-directory of the FTP Server install directory. For a default

installation the Spyder program is in C:\Spyder\FTP\ftp\ProductSoftware\. The Spyder software is program

920A91.xx.bin, where xx is a two digit number specifying the current revision level.

www.maxcessintl.com

Spyder Firmware Update

MI 850A324 1 C

Page 4

Use Windows Explorer or My Computer to go to the C:\Spyder\FTP\ftp\ProductSoftware\ directory. Make a note of

the 920A91.xx.bin file in this directory. You will need this file name to tell the Spyder which software to download in

section 3.4.

Important: If your CD or e-mail contains a 920Axx.xx.bin file, please copy the file from the CD or e-mail to the

C:\Spyder\FTP\ftp\ProductSoftware\ directory. This will assure you are getting the latest version. Use this file

name in section 3.4.

Skip to section 3.3 if the FTP Server is running.

WARNING: There is a hardware change in the Spyder between versions 920A91.07 and 920A91.08.

If your Spyder unit has any version 920A91.07 or below you cannot upgrade to version 920A91.08 or

higher.

3.2. RUNNING THE FTP SERVER SOFTWARE

Double click the FTP Server shortcut on your desktop or use the Start menu, Programs, Home FTP Server to start

the FTP Server. Verify the server is running by clicking the "Ftp Server" tab and the lower left corner should show a

green box showing the server is running. If the server is not running press the "Start Server" button. See Figure 1.

3.3. CONFIGURING THE NETWORK CONNECTIONS

The computer and the Spyder must be on the same network subnet and each must have a unique IP Address. The

Spyder defaults to the subnet 192.168.1.xx and has an IP Address of 192.168.1.100. On your computer open the

Network Connections. Double click on the LAN icon and then click on Properties. You should see a window similar

to figure 2. Highlight the Internet Protocol(TCP/IP) and click on Properties and a window similar to figure 3 should

show. There are slight differences in these two windows depending on which Windows operating system you are

using.

Figure 2. Local Area Connections Figure 3. TCP/IP Properties

www.maxcessintl.com

Spyder Firmware Update

MI 850A324 1 C

Page 5

Use the steps in either 3.3.1 or 3.3.2 depending on your computers present configuration.

3.3.1 If your computer has "Obtain an IP Address Automatically" selected.

Remember to return to the present configuration when you are finished programming the Spyder, otherwise you

may not be able to access your company's network.

- Select "Use the following IP Address".

- Type in the IP Address and Subnet Mask as shown in figure 3.

- Click "OK" on both the figure 3 and figure 2 windows

- Set the Spyder's FTP Address to be the same as the computers IP Address.

- Verify the Spyder's IP Address is 192.168.1.100 and the Subnet Mask is 255.255.255.0.

- Go to section 3.4.

3.3.2 If your computer has "Use the following IP Address" selected.

- Set the Spyder's IP Address to a number with the same first three numbers as your computer and make the

fourth number different. If your computer has an IP Address of 172.16.1.180 then make the Spyder's IP

address 172.16.1.xx, where xx is a number between 1 and 254.

- Set the Spyder to the same Subnet Mask as your computer.

- Set the Spyder's FTP Address to be the same as the computers IP Address.

- Go to section 3.4.

3.4. PROGRAMMING THE SPYDER

WARNING: There is a hardware change in the Spyder between versions 920A91.07 and 920A91.08.

If your Spyder unit has any version 920A91.07 or below you cannot upgrade to version 920A91.08 or

higher.

Turn power off to the Spyder. Press the "Up" and "Down" arrow while turning the power on to the Spyder until the

program number is displayed. The display should show:







Press the "Down" arrow key.



If the program number showing is not the same as the program number from section 3.1, press the "Enter" key to

edit the program number.

Press the "Down" arrow key to start programming.

When programming is finished the screen will show:



If an error message is displayed, then programming has not completed.

The Spyder now has the latest software. Turn power off and then on to the Spyder to complete the installation.

The Spyder will now show the new 920Axx.xx number for a few seconds during power up

www.maxcessintl.com

Spyder Firmware Update

MI 850A324 1 C

Page 6

4. PROBLEMS

Problem

Possible Cause

Solution or Diagnostic

Screen blank or all dark.

Contrast grossly

misadjusted.

Remove power. While holding

down and buttons, reapply

power. The Spyder will be sweep

through the contrast settings.

When the contrast is at or near the

desired level press .

FTP Login Failed

Computer or Spyder

network parameters not

set properly.

Spyder FTP directory,

FTP username, or FTP

password not set properly.



Ethernet cable not

connected.

FTP server not running on

computer.

Check Computer and Spyder

network parameters IP Address,

Subnet Mask, FTP Address.

Reset Spyder to factory defaults.

Remove power. While holding down

the and buttons, reapply

power.

Check Ethernet connection.

Verify the FTP server is running.

See section 3.2.

Get Program Failed

Invalid program number.

Make sure the Spyder program

number is correct.

Program CRC Invalid

Data transfer corrupted.

Corrupt program file.

Try programming Spyder again.

Go to www.maxcessintl.com and

get the latest program.

Displays “Booting…”

Version 920A91.08 or

higher is loaded on

Spyder that previously

had 920A91.07 or below.

See warning in section 3.4.

Program Spyder with 920A91.07

version.

www.maxcessintl.com

Spyder Firmware Update

MI 850A324 1 C

Page 7

5. SPYDER RESET FUNCTIONS

The Spyder has functions which are activated by holding down keys while turning on power.

5.1. Automatic Contrast Adjust

The automatic contrast adjustment is activated by holding down the "Left" and "Down" arrow keys while

turning on the power. Hold the keys for at least 6 seconds after power is on. The display will repeatedly

sweep through the full contrast range until the "Enter" key is pressed. When the display is readable, press

the "Enter" key to exit contrast adjustment.

5.2. Reset All Parameters Except Calibrations to Defaults

All parameters except calibrations will be reset to defaults by holding down the "Left" and "Right" arrow

keys while turning on the power. Hold the keys until the screen shows "Resetting Parameters".

5.3. Reset All Parameters to Defaults (Including Calibrations)

All parameters will be reset to defaults by holding down the "Right" and "Up" arrow keys while turning on

the power. Hold the keys for at least 6 seconds after power is on.

5.4. Download Software

To download new software hold down the "Up" and "Down" arrow keys while turning on power and hold the keys

until the display shows "Update Software".

AMERICAS

Tel +1.405.755.1600

Fax +1.405.755.8425

sales@maxcessintl.com

www.maxcessintl.com

EUROPE, MIDDLE EAST

AND AFRICA

Tel +49.6195.7002.0

Fax +49.6195.7002.933

sales@maxcess.eu

www.maxcess.eu

CHINA

Tel +86.756.881.9398

Fax +86.756.881.9393

info@maxcessintl.com.cn

www.maxcessintl.com.cn

INDIA

Tel +91.22.27602633

Fax +91.22.27602634

india@maxcessintl.com

www.maxcess.in

JAPAN

Tel +81.43.421.1622

Fax +81.43.421.2895

japan@maxcessintl.com

www.maxcess.jp

KOREA, TAIWAN,

AND SE ASIA

asia@maxcessintl.com

www.maxcess.asia

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Maxcess Controller Handbücher

Maxcess

Maxcess MAGPOWR DFC-90 Bedienungsanleitung

Maxcess

Maxcess Fife GMA-BL Bedienungsanleitung

Maxcess

Maxcess FIFE DP-20 PLUS Bedienungsanleitung

Maxcess

Maxcess GMA-BL-1-1 Handbuch

Maxcess

Maxcess MAGPOWR HEB250 Montage- und Bedienungsanleitung

Maxcess

Maxcess H6630EM Bedienungsanleitung

Maxcess

Maxcess Fife GMA-BL Gebrauchsanweisung

Maxcess

Maxcess SE-46C Kurzanleitung

Maxcess

Maxcess Fife Polaris DP-20 Bedienungsanleitung

Maxcess

Maxcess MAGPOWR Spyder-Plus Bedienungsanleitung

Maxcess

Maxcess D-MAXE Bedienungsanleitung

Maxcess

Maxcess FIFE D-MAXE 1 Bedienungsanleitung

Maxcess

Maxcess FIFE DP-20 PLUS Bedienungsanleitung

Maxcess

Maxcess Magpowr IPT Bedienungsanleitung

Maxcess

Maxcess Fife Polaris DP-20 Bedienungsanleitung

Maxcess

Maxcess MAGPOWR DLCA NET-S1 Bedienungsanleitung

Maxcess

Maxcess MAGPOWR CYGNUS-S3 Series Bedienungsanleitung

Maxcess

Maxcess MAGPOWR Spyder-Plus-S1 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch