Maximon Max-728 Bedienungsanleitung

Max-728 VHF/UHF Transceiver

User Manual

PRECAUTIONS

·Refer service to qualified technicians only.

·Do not operate the transceiver nor charge a battery pack in an explosive

atmosphere (gases, dust, fumes, etc.).

·Turn OFF the transceiver while taking on fuel or while parked in a

gasoline service station.

·Do not modify nor attempt to adjust this transceiver for any reason.

·Do not expose the transceiver to long periods of direct sunlight, nor

place it close to heating appliances.

·Do not place the transceiver in excessively dusty, humid, and/or

wet areas, nor on unstable surfaces.

SAFETY: It is important that the operator be aware of and underst

and hazards common to the operation of any transceiver.

CONTENTS

UNPACKING AND CHECKING EQUIPMENT

Supplied Accessories----------------------------------------------1

PREPARATION

Charging the Battery Pack---------------------------------------2-3

Installing/Removing the Battery Pack---------------------------4

Installing the Antenna----------------------------------------------5

Installing the Belt Clip---------------------------------------------5

Installing the Cover over the Speaker / Microphone Jacks----6

Installing the Speaker/ Microphone------------------------------6

GETTING ACQUAINTED---------------------------------------7

OPERATION--------------------------------------------------------8

AUXILIARY FUNCTIONS

Time-out Timer-----------------------------------------------------9

Battery Saver--------------------------------------------------------9

Low Battery Warning Monitor------------------------------------9

CTCSS/DCS CODES

50 CTCSS frequency codes (Hz)----- ---------------------------10

104+1 DCS codes--------------------------------------------------10

TROUBLESHOOTING GUIDE---------------------------------11

FREQUENCY CHART-------------------------------------------12

ADVANCED OPERATIONS

Safety Training Information--------------------------------------13

Electromagnetic interference / Compatibility------------------14

UNPACKING AND CHECKING EQUIPMENT

Carefully unpack the transceiver. We recommend that you identify the

items listed in the following table before discarding the packing material.

If any items are missing or have been damaged during shipment, file a

claim with the carrier immediately.

Supplied Accessories

ITEM QUANTITY

Antenna 1

Battery charger 1

AC adaptor 1

Battery pack 1

Belt clip 1

Instruction manual 1

PREPARATION

Charging the Battery Pack

The battery pack is not charged at the factory; charge it before use.

Initially charging the battery pack after purchase or extended storage

(greater than 2 months) will not bring the battery pack to its normal

operating capacity. After repeating the charge/discharge cycle two or

three times, the operating capacity will increase to normal.

CAUTION

DO NOT RECHARGE THE BATTERY PACK IF IT IS ALREADY

FULLY CHARGED. DOING SO MAY CAUSE THE LIFE OF THE

BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY

BE DAMAGED.

AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT

FROM THE CHARGER. CHARGING THE BATTERY PACK FOR

MORE THAN 5 DAYS MAY REDUCE THE BATTERY PACK LIFE.

Note

The ambient temperature should be between 41 and 104°F (5 and

40) while charging is in progress. Charging outside this range may

not fully charge the battery.

Always switch OFF the transceiver equipped with a battery pack

before charging. Using the transceiver while charging its battery pack

will interfere with correct charging.

The battery pack life is over when its operating time decreases even

though it is fully and correctly charged. Replace the battery pack.

Plug the AC adaptor cable into the adaptor

jack located on the rear of the charger.

Plug the AC adaptor into an AC outlet.

Slide the battery pack or transceiver with

a battery pack into the charger.

Make sure the battery pack contacts are in contact with the charging

terminals.

The charger LED lights and charging begins.

After charging the supplied battery pack for 4 hours, remove it or the

transceiver equipped with it from the charger.

The charger turn to green automatically after charging is completed.

Unplug the AC adaptor from the AC outlet.

Installing / Removing the Battery Pack

The average life of the supplied battery pack is 12 hours.

Average times are calculated using 5% transmit time, 5% receive time,

and 90% standby time.

CAUTION

DO NOT TAMPER WITH THE BATTERY TERMINALS NOR

DISPOSE OF THE BATTERY BY FIRE.

NEVER ATTEMPT TO REMOVE THE CASING FROM THE

BATTERY PACK.

To remove the battery pack, pull back on the release latch and slide the

pack away from the transceiver.

Slide the battery pack along the back of the transceiver.

Match the bottom of the battery pack with the corresponding grooves on

the back of the transceiver.

Installing the Antenna

Screw the antenna into the connector on the top of the transceiver by

holding the antenna at its base and turning it clockw-ise until secure.

Note: The antenna is neither a handle, a key ring retainer, nor a

speaker/microphone attachment point. Using the antenna in these ways

may damage the antenna and degrade your transceiver's performance.

Installing the Belt Clip

If necessary, buckle the belt clip to the back of the battery pack.

Note:

Make sure the battery pack contacts are in contact with the charging

terminals.

The charger LED lights and charging begins.

CAUTION

DO NOT USE GLUE WHICH IS DESIGNED TO PREVENT SCREW

LOOSENING WHEN INSTALLING THE BELT CLIP,AS IT MAY

CAUSE DAMAGE TO THE TRANSCEIVER.

ACRYLIC ESTER, WHICH IS CONTAINED IN THESE GLUES,

MAY CRACK THE TRANSCEIVER'S BACK PANEL.

Installing the Cover over the Speaker/ Microphone Jacks

If you are not using a speaker / microphone, install the cover over the

speaker /microphone jacks using the supplied screw.

Note:

To keep the transceiver water resistant, you must cover the speaker /

microphone jacks with the supplied cover.

Installing the Speaker/ Microphone

If you are not using a speaker / microphone, install the cover over the

speaker /

microphone jacks.

Note:

To keep the transceiver water resistant, you must cover the speaker /

microphone jacks with the supplied cover.

GETTING ACQUAINTED

Notices:

Side button 2 and side button 3 can be programmable by PC software to

these functions:

Monitor, Squencl on/off, Scan on/off, Scan temperary delete, High/Low

power, Talk about,

Reverse frequency, VOX on/off, Scrambler on/off.

Above functions can be programmable through short press or long press

at side button 2 and side button 3.

Those functions can be programmable through PC softare:

Tx total time (s), Squelch, Voice annunciation, VOX gain level, Band

width, Tx power rank,Beep, scrambler.

OPERATION

Switch ON the transceiver by turning the Power switch / Volume control

clockwise.

A beep sounds

Adjust the volume by pressing and holding the Monitor key, then rotating

the Power

switch / Volume control.

Rotate the Channel selector to select your desired channel.

When you receive an appropriate signal, you will hear audio from the

speaker.’

To make a call, press and hold the PTT switch; then, speak into the

microphone using your normal speaking voice.

Hold the microphone approximately 1.5 inches (3 to 4 cm) from your lips.

Release the PTT switch to receive.

Note: When the battery pack voltage becomes too low, transmisson will

stop and the LED will blink red. See "Low Battery Warning" on page 9.

Inhaltsverzeichnis

Andere Maximon Transceiver Handbücher

Maximon

Maximon Max-555 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung