Maximum 21030 Bedienungsanleitung

English User manual

Deutsch Installationsanleitung

Dansk Brugervejledning

Powerline Network System

Internet access to any power outlet

MAXIMUM 500 LOOP KIT

Item no.: 21030

Installation Guide

This document describes installation of the powerline products.

Please read this document before installing the product.

This publication contains the following sections:

• Important safety instructions

• The first thing you need to know before you begin to install

• Product installation guide

• Specification

Important Safety Instructions

This product is intended for connection to the AC power line. For instal-

lation/removing instructions, refer to the Installation section. The following

precautions should be taken when using this product.

• Please read all instructions before installing and operating this product.

• Please keep all instructions for later reference.

• Please follow all warnings and instructions marked on the product.

Cleaning / reservations

• Unplug the AC coupler from the wall outlet before cleaning. Use a damp

cloth for cleaning. DO NOT use liquid cleaners or aerosol cleaners.

• Do not operate this product near water.

• Use only in dry conditions, not for outdoor use.

• The total wattage of the connected devices must not exceed 2300 watts.

• This product should never be placed near or over a radiator, or heat register.

• This product relies on the building’s electrical installation for short-circuit

(over current) protection.

• Ensure that a fuse or circuit breaker no larger than 120 VAC 20A or 240 VAC

16A is used on the phase conductors (all current-carrying conductors).

• Do not allow anything to rest on the product interconnect cords.

• Do not locate this product where people may walk on the cords.

• The product can be operated at an ambient temperature of 40°C.

English

• For pluggable equipment, the socket-outlet shall be installed near the

equipment and shall be easily accessible.

• Only a qualified technician should service this product. Opening or removing

covers may result in exposure to dangerous voltage points or other risks.

• Unplug the AC coupler from the wall outlet and refer the product to quali-

fied service personnel for the following conditions:

• When the interconnect cords are damaged or frayed.

• If liquid has been spilled into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally when the operating

instructions are followed.

• If the product exhibits a distinct change in performance.

The first thing you need to know before you begin to install the CD

1. Before installing, make sure your PC meets these requirements

for hardware installation:

• Microsoft Windows® 98SE, ME, 2000, XP, Vista, Mac OS or linux OS

• Pentium® III or better, clock rate faster than 2.0GHz recommended

• At least one free Ethernet port for 500Mbps PLC Pass Through

2.YourPCmustnotbeconguredforanothernetwork.Thismeansthat:

• No network clients except for Microsoft Network*, Client for Netware*

Networks, or Microsoft Family Logon* are installed.

• NonetworkservicesexceptleandprintersharingforMicrosoftNetworks

or Personal Web Server* are installed

• No network protocols except Microsoft’s TCP/IP, IPX/SPX, NetBEUI, or

Net BIOS support for IPX/SPX are installed

3. Network installation requires two steps:

• Install the 500Mbps PLC-Pass Through

• For each PC to be added to the network, repeat the process

4. Check that you have the following parts for each PC on the network:

• Product installation guide for 200Mbps PLC Pass Through

English

• 500Mbps PLC Pass Through

• Ethernet Cable (CAT 5)

5. Familiarize yourself with the Powerline device connections:

• There is only one Ethernet port. This is used for the connection with PC,

xDSL/Router, Cable Modem, or Wireless AP.

6. Limitation of the PLC device:

• To meet the safety regulation, the longest distance between powerline

carrier devices will be limited at 200 meter and for in-house use only.

More than 200 meter will cause the signal reduction or data loss.

• Always connect to the nearest source where possible and avoid exten-

sions power connectors. Every step that brings you further away from the

source (your power network) will cause signal reduction or loss.

• There are some limitations in regards to the house main installation.

Some phase jumps might not be possible or cause signal reduction or loss.

Product Installation Guide

Notice:

Do not plug the device into a power strip or surge protector because these

devicesmayconsistoflterandimpairsignal.Alsoavoidpluggingthe

device right next to noisy sources such as cell phone charger, Halogen light,

Energy saving bulb, noisy desktop computer, vacuum cleaner, etc. Both

cases result in poor transmission speed. Nevertheless, you can put the

noisysourcetothePassThrough’soutlet.Theoutletwilllteroutthenoise

and improve the Powerline communication performance.

English

To install for the PC local Powerline network

• Use the supplied Category 5 Ethernet cable to connect powerline product

and your PC’s Ethernet port.

• Plug the powerline product to power outlet.

• The PWR LED indicator will light on after plugging.

• You can repeat steps 1 and 2 for connecting the others.

• The PLC-ACT LED indicator starts blinking when the data communication

proceeds on Powerline.

• The ETH-ACT LED indicator starts blinking when the data communication

proceeds on Ethernet.

To share a xDSL or cable modem with Internet access service

1. Connect one powerline product to the broadband router

• Plug the powerline into an AC outlet.

• Plug the provided Ethernet cable into the RJ45 connector of the

powerline product and plug the other end of the cable into an available

Ethernet port of the Router.

2. Connect the other powerline products(s) to the PC(s) to share the Internet access

• Plug the Bridge into an AC outlet.

• Plug the provided Ethernet cable into the RJ45 connector of the powerline

product and plug the other end of the cable into Ethernet port on the PC.

As wireless AP (Access Point) Extender

1. Connect one powerline to the broadband router

• Plug the Bridge into an AC outlet.

• Plug the provided Ethernet cable into the RJ45 connector of the

powerline product and plug the other end of the cable into an available

Ethernet port of the broadband router.

2. Connect the other Pass Through to the wireless AP.

• Plug the Bridge into an AC outlet.

• Plug the provided Ethernet cable into the RJ45 connector of the powerline prod-

uct and plug the other end of the cable into the Ethernet port on the wireless AP.

English

Installation

Because powerline product sends data over the powerline, it is recommended that

you plug directly into a power outlet. Do not plug the device into a UPS or power

stripwithsurgeprotection.Thepower-passthroughproducthasitsownpowerlter

for protection against surges.

English

7English

LED/buttons

*1 : The “Power“ LED indicator will blink in standby mode. It will get into standby

mode, if you plug the device to outlet and no Ethernet link detected after booted

and 60 second later. If you unplug the Ethernet cable, it will get into standby mode

after 60 seconds. Under standby mode, PLC and ETH LEDs will both be off.

Push Buttons (Only applicable for models with push button)

Push button functions are disabled under Standby mode.

Setup Button Usage:

First time to setup your private network:

Step 1.

Press and hold the device’s “SETUP” button for more than 10 seconds. You can re-

lease the button when you see all the device’s LEDs are off and restart. The original

network encryption setting is cleared.

Step 2.

Repeat Step 1 to clear another device’s original network encryption setting.

Step 3.

Press both devices’ “SETUP” button for 1 to 3 seconds. You will see both devices’

“Power” LED start blinking. Both devices start to communicate and try to setup their

private network encryption. They will complete the new private network encryption

setting within 10 seconds. You will see both devices’ all LEDs are off and restart.

Note: The setup operation timeout is 120 seconds.

PWR

(Red)

On: Power on

Blinking: Standby mode (*1)

PLC

(Green/Orange/Red)



ETH

(Green)

On: Ethernet Link detected

Step 4.

If failed, please repeat Step 1 to Step 3 again.

Add a new device to the existing private network:

Step 1.

Plug the new device. Press and hold its “SETUP” button for more than 10 seconds

to clear the original network encryption setting.

Step 2.

Press the new device’s “SETUP” button for 1 to 3 seconds. The “Power” LED starts

blinking.

Step 3.

Select a random device from the existing private network. Press its “SETUP” button

for 1 to 3 seconds. The device’s “Power” LED starts blinking.

Step 4.

The new device starts to communicate with the device from existing private net-

work, and tries to join this existing private network. It will complete the new private

network encryption setting within 10 seconds. You will see the new device’s all

LEDs are off and restart after completing the private network setting. The existing

private network device’s “Power” LED become solid.

Note: The setup operation timeout is 120 seconds.

Step 5.

If failed, please repeat Step 1 to Step 3 again.

Leave the private network:

Step 1.

If the device wants to leave the private network, press and hold the device’s

“SETUP” button for more than 10 seconds to clear the network encryption setting.

This device will leave the private network.

Reset Button Usage:

1. Reset the device to the factory default setting:

Push the device’s “RESET” button for 1 to 3 seconds. You will see the device’s all

LEDs are off and restart. The device’s setting resets to the “factory defaults”.

English

Specikation

English

Powerline Network

Specification

Items Description

PHY Rate 500Mbps(IEEE 1901 and HomePlug® AV compliant)

Effect Data Rate TCP: Up to 210 Mbps effective throughput ,250 Mbps with multiple sessions

UDP: Up to 250Mbps effective throughput

Frequency Band 2~68 MHz (With Mask)

Access Methods priority-based CSMA/CA channel access schemes maximize efficiency and

throughput

Qos –Integrated Quality of Service (QoS) Enhancements

–Hardware Packet Classifiers for ToS, CoS and IP Port Number



–Supports IGMP managed multicast sessions

Modulation OFDM (QAM 8/16/64/256/1024/4096, QPSK, BPSK, ROBO)

Standards IEEE 802.3, IEEE 802.3U,HomePlug AV Protocol Compliance with HomePlug

1.0 coexistence capability

Operating System Microsoft Windows®2000, XP, Vista ,Windows 7(for utility-program only)

Nodes

Up to 63 slaves with 1 master, 64 total devices

4 overlapping networks for neighbor networks with CCo failover

Up to 4 masters with up to 252 slaves, 256 total devices in 4 AVLNs

Max 64 bridged devices per station

Up to 4096 addressable devices including bridged devices

IGMP IGMP snooping with multicast to multiple unicast support in CSMA

o Enhanced IPv4/IGMPv1-3 snooping support

o Enhanced Support for IPv6 and MLDv1-2 snooping

Encryption 128-bit AES Link Encryption with key management

Push button SETUP button

RESET button

Port One 100M/Giga Bit Ethernet port

Distance AC Wire : 200 meters

LEDs PWR (Red)

PLC(Green/Orange/Red throughput indicator)

ETH (Green)

Environment Temperature Operating : 0~40 ℃

Storage : -20~60 ℃

Relative Humidity Operating : 10~85% Non-Condensing

Storage : 5~90% Non-Condensing

Power Source 100 ~240 VAC 50/60Hz

Power

Consumption 5W Max (Normal mode)

Below 2W (Standby mode)

Certification CE

English

Utility Program User Guide for powerline products

Index

1. Introduction 10

1.1. System Requirements 10

1.2. Installation 10

1.3. Run the Utility 11

2. How to use 11

2.1. Main Tab 11

2.2. Diagnostics Tab 15

2.3. About Tab 16

1. Introduction

ThisUtilityProgramenablesuserstond500MbpsPLC-EthernetBridge

devices on the Powerline network, measures data rate performance, ensures

privacyandperformsdiagnosticsbysettinguserdenedsecurePowerline

networks.

1.1. System Requirements

Operating System Microsoft Windows XP, Vista, 7

Browser Microsoft Internet Explorer 5.0 or later.

CPU Intel Pentium III or better, clock rate faster than 2.0GHz recommended

RAM At least 128MB

Free Disk Space At least 20MB

Network Interface At least one Fast/Gigabit Ethernet network card, and Ethernet Cord

1.2. Installation

First, you need to verify that there is no other Powerline utility installed on

your computer before installing this utility. If there is another utility installed,

please uninstall it.

Then, please insert the Utility CD-ROM into the computer’s CD-ROM drive.

The CD will launch an IE browser. Click the necessary link to start installa-

tion. Please install WinPcap v4.1.1 (you can download it from http://www.

Inhaltsverzeichnis

Andere Maximum Adapter Handbücher

Maximum

Maximum 18050 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung