MAY AYIA Bedienungsanleitung
Manual
AYIA 1.1
Tools (supplied):
ALLEN KEY
Metric sizes:
Mudguard: 4
Saddle and brakes: 5
Handlebar: 6
WRENCH
Size:
Pedals: 15
Pedals
The following parts are packed together
with the bicycle frame and the tires:
1
We recommend you use lubricating oil
(not supplied) when necessary as indicated
in the assembly instructions.
Tools
Step 1: INSTALLING THE HANDLEBAR:
Slot the handlebar into the head tube at a straight angle and make sure the brake
cables are positioned in front of the handlebar. We recommend applying some
lubricating oil to the head tube before inserting it. Adjust the height and the angle
as desired. Use an allen key (size 6) to attach the handlebar to the bike. Makesure
the bolt istightly fastened.
In case you are also mounting the bike basket to your AYIA women’s bike,
please follow the steps of the basket manual first, before proceeding with
the AYIA build-up.
Congratulations!
You are now a proud owner of a limited edition AYIA Bike.
You are about to assemble your new bike and we are going to guide you through
the ten easy steps needed to complete the assembly. Your bike has been shipped
virtually complete and the last 10% is now up to you – but have no worries this part
is very simple!
Step 2: MOUNTING THE SADDLE:
Insert the saddle into the saddle tube
and fix it to your desired height.
Make sure the clip of the frame is well
tightened by using the allen key
(size 5). We recommend applying some
lubricating oil to the saddle tube
before inserting it.
Step 3: ATTACHING THE PEDDALS
TO THE BIKE:
The pedals are marked R (right) and L
(left). We recommend applying some
lubricating oil to the pedal crank before
inserting it. Secure the bolt towards
the front of the bike. Use the wrench
to secure the bolt tightly.
2
4
2
Step 4 +5: MOUNTING THE MUDGUARD:
Loosen the rim brake from the fork as marked on the photo (4). Caution: don’t
change the order of the components. Remove the two back components and insert
the fixture of the mudguard in between the rim brake as marked on the photo. Put
both components back in their old position on the rim brake and fix the rim brake
back to the fork. Make sure the screw is secured tightly.
Use the supplied screws and screw coasters to fix the splint of the mudguard
onthe fork end. The screw coaster should be positioned on the outside. Caution:
tighten both sides equally.
2
Step 7: ADJUSTING THE BRAKES
Make sure the brake pad is positioned parallel to the wheel rim according
to our picture. The brake pad shouldn’t be mounted too high so it doesn’t touch the
tire. It should only touch the flat sides of the wheel rim (when brakes are in action).
Step 6: MOUNTING THE FRONT WHEEL:
The wheel is marked with an arrow
showing the riding direction. Loosen
the front screw nuts on the wheel and
place the fork between the bolt and the
safety washer. Make sure the safety
washer is placed on the outside of the
fork so you can insert it into the hole as
illustrated on the right.
Use a wrench to tighten the screw nuts
properly. Also tighten the screw nuts of
the back wheels.
Safety washer
Step 8: FINE ADJUSTING THE BRAKES
Option 1: Release or tighten the brakes
by twisting the screw at the brake clamp.
Option 2: Release or tighten the brakes by
twisting the set screw at the brake lever.
This will help loosen the brake wire
in order to use pliers to pull the wire.
Ensure the wire is tight enough and yet
doesn’t touch the wheel rim when
the brakes aren’t in action. Then close
the clamp with the allen key.
Repeat the same procedure for the
rear wheel brakes.
Step 10: FINAL DETAILS
Grease the chain and tighten
all remaining bolts and screws.
Step 9: ADJUSTING THE GEARS
OF THE SHIFTER
First, set the shifter on your handlebar into
the second gear.
Use a wrench in size 10 to loosen the
front
lock nut (a) on the gear which is
mounted on
your back wheel. You will then be able to turn
the adjustment knob (b) with your fingers in
order to align the yellow indicator on the body
of the shifter as displayed on the photo (c).
Make sure the yellow indicator is placed in the
exact middle.
b a
c
Make sure the
yellow indicator
is placed in the
middle between
the lines.
Follow and contact us on Instagram:
@may_ _ltd
info@may-ltd.com
MAY International SA
Bahnhofstrasse 134
8957 Spreitenbach, Switzerland
www.may-ltd.com
Inhaltsverzeichnis
Andere MAY Fahrrad Handbücher
