Maytag MBF2256KEB - Bottom Freezer Refridgerator Bedienungsanleitung

Installation

Materials Needed:

•3⁄8”hex head driver

•Carpenter’s level.

1. Remove toe grille.

•Grasp firmly and pull

outward to unclip.

2. Using hex head driver, turn

the front adjustment screws (A) on each side to

raise or lower the front of the refrigerator (see

illustration below).

3. Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

4. Using a carpenter’s level, make sure front of

refrigerator is 1⁄4”(6 mm) or 1⁄2bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

5. Turn stabilizing legs (C) clockwise until firmly

against floor.

6. Turn adjustment screws (A) counterclockwise to

allow the full weight of the refrigerator to rest on

the stabilizing legs.

.Replace the toe grille.

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Location

•Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material (contact a qualified contractor).

•Do not install where temperature falls below 55° F

(12° C) or rises above 110° F (43° C). Malfunction may

occur at this temperature.

•Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow 1⁄2”space at top and 1⁄2”space behind the machine

compartment cover (located in the rear) for proper air

circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a recess

where the top of the refrigerator is completely covered,

use distance from floor to top of hinge cap to verify

proper clearance.

Transporting Your Refrigerator

•NEVER transportrefrigerator on its side. If an upright

position is not possible, lay refrigerator on its back.

Allow refrigerator to sit upright for approximately 30

minutes before plugging it in to assure oil returns to

the compressor. Plugging the refrigerator in

immediately may cause damage to internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYStruck refrigerator from itsside or

back–NEVERfrom itsfront.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handleswhen

possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

Leveling

To protect property and refrigerator from

damage, observe the following:

• Protect vinyl or other flooring with cardboard, rugs,

or other protective material.

•Do not use power tools when performing leveling

procedure.

CAUTION

To enhance the appearance and maintain performance,

the refrigerator should be leveled per instructions

below.

Notes:

•Complete any required water supply connection

before leveling.

•Some models only have adjustment screws (A).

ABA

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

Installation

To avoid electrical shock which can cause

severe personal injury or death, observe the

following:

• Disconnect power to refrigerator before removing

doors or drawer. Connect power only after

replacing doors or drawer.

WARNING

To avoid damage to walls and flooring, protect vinyl

or other flooring with cardboard, rugs or other

protective material.

CAUTION

Materials Needed:

•Phillips screwdriver

•5⁄16”hex head driver

•3⁄8”hex head driver

1. Unplug power cord from power source.

2. Remove toe grille and bottom bracket cover(s)

(see page 3).

3. Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

4. Unscrew 5⁄16”hex head screws from top

hinge to remove hinge and retain all

screws for later use.

5. Lift refrigerator door from center

hinge pin.

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

6. For swing freezer door models only: Hold

freezer door while removing hinge pin

with a 5⁄16”hex head driver. Remove door

from bottom hinge and retain hinge pin

for later use.

For pullout freezer drawer models

only: Remove plastic sleeve, if

present. Remove center hinge

pin with a 5⁄16”hex head driver.

Retain hinge pin and plastic

sleeve for later use.

7. Remove Phillips screws to

remove center hinge and

retain all screws for later

use.

8. Remove bottom hinge or

stabilizing bracket with 3⁄8”

hex head driver and retain

screws for later use. Lift out bottom

hinge pin (on freezer door models).

9. If your model has a pullout freezer

drawer, see page 5 for drawer removal

instructions.

Installation

Pullout Freezer Drawer

(select models)

To avoid electrical shock which can cause severe

personal injury or death, disconnect power to

refrigerator before removing doors. After replacing

doors, connect power.

WARNING

To prevent accidental child entrapment or

suffocation risk, do not remove the divider in the

top freezer basket.

DANGER

Toavoid possible injury, product, or property

damage, you will need two people to perform the

following instructions.

CAUTION

Materials Needed:

• Phillips screwdriver

To Remove:

1. Pull drawer open to full extension.

2. Tilt the lower basket

forward and lift to remove.

3. On each white drawer

bracket is a basket cradle

with two snap attachments.

Torelease each cradle,

unlatch the snaps by

pushing them inward,

away from the side

bracket. Lift the cradles

off of the rails.

4. Remove Phillips screw

from each of the drawer

slides (select models).

5. Lift top of drawer front

to unhook the drawer

from the slides. Lift

door front out to

remove.

To Install:

1. Pull both rails out to

full extension.

2. While supporting

door front, hook

supports into slots

located on inside of

each slide.

Note: All four drawer bracket supports must be in

the proper slots for the drawer to function properly.

6. Tilt the lower basket front down and set it down

into the basket cradles.

Basket cradle

snap attachments

3. Lower door front into final position.

4. Replace and tighten Phillips screws that were

removed from the drawer slides (select models).

5. Place the basket cradles back onto the drawer

slides. Align basket cradle snaps with the slots on

the drawer brackets and press each cradle toward

the bracket until it clicks.

Installation

Reinstallation of the Doors

Materials Needed:

• Phillips screwdriver

•5⁄16”hex head driver

1. Install hinge assemblies:

• Install top hinge loosely with 5⁄16”hex head screws.

• Install center hinge with Phillips screws.

•Freezer door models: Install bottom hinge with

3⁄8”hex head screws.

2. Freezer door models: Insert bottom hinge pin.

• Locate bottom hinge hole closest to

outside edge of cabinet, and insert

bottom hinge pin. Replace any door

shims, if present.

3. Freezer door models: Place hinge

side of freezer door on bottom hinge

pin and hold freezer door upright

while installing center hinge pin with

5⁄16”hex head driver.

• Replace plastic sleeve.

• Replace any applicable door shims.

• Make sure the hinge pin is installed tightly.

4. Place hinge side of refrigerator door on center hinge

pin.

5. While holding refrigerator door

upright, tighten down top hinge

with 5⁄16”hex head driver and

replace hinge cover.

Door Reversal

In some installations, reversing the door swing allows

for more convenient access to stored items. Both doors

can be reversed on freezer door models and the fresh

food door is reversible on freezer drawer models.

Materials Needed:

• Flat screwdriver

• Phillips screwdriver

•5⁄16”hex head driver

•3⁄8”hex head driver

1. Remove door(s) (see page 4).

2. Transfer cabinet plugs and cabinet

screws to opposite side of cabinet.

•Remove cabinet plugs with flat

blade of screwdriver tip wrapped in masking tape.

3. Transfer door stops from bottom edge of fresh food

door and freezer door, if applicable, to opposite

side of door edge.

• Use a Phillips screwdriver

for removal and installation.

4. Install handles (see pages

6-8).

5. Reinstall the door(s).

Handles

Remove and discard handle packaging and tape.

Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your

model below.

Fresh Food Handles

Standard Front Mount Handle

Materials Needed:

•Phillips screwdriver

•5⁄16”hex head driver

To Install:

1. Remove 1⁄4”hex head screws from

door face with hex head driver, and

Phillips screw from top of door.

•If reversing door, remove door plugs

from opposite side of door and insert

in screw holes.

2. Align handle holes with screw holes on

door face and secure with two door face

screws from step 1.

To avoid possible injury and damage to property:

• Place doors on a nonabrasive surface protected by

towels or rugs while working directly on doors.

CAUTION

Note: If not installed, the handle is located in the

interior of the fresh food compartment or attached

to the back of your refrigerator.

• Remove center mullion screws with 5⁄16”hex head

screwdriver.

•Freezer door models: Remove bottom mullion

screws with 3⁄8”hex head driver.

Cont.

3. Locate handle trim in literature pack and

install over top and bottom of handle, as

illustrated.

• Secure top handle trim with remaining

screw removed in step 1.

• Snap bottom trim over bottom portion

of handle.

To Remove:

1. Remove top handle trim by removing top

handle screw.

• Retain trim and screw for later

replacement.

2. Pry bottom handle trim from handle with

screwdriver flat blade wrapped in

masking tape.

•Retain trim for later replacement.

3. Remove two hex head screws.

• Retain screws for later replacement.

Side Mount Handle

Materials Needed:

•Phillips screwdriver

ToInstall:

1. Remove screws from the side of the

door.

2. Align the side mount handle with the

predrilled holesin the door panel.

3. Insert the screws in the sequence as

shown.

Installation

4. Ensure the door handle is snug to the

door panel.

To Remove:

Reverse installation procedure.

Upper

Handle

Lower

Handle

Freezer Handles

Partial-Width Handle

Materials Needed:

• Phillips screwdriver

To Install:

1. Install handle by fastening with

screws removed from edge of door.

• If reversing freezer door, remove

door plugs from top edge of door

and insert into screw holes.

To Remove:

1. Remove handle screws with Phillips

screwdriver and retain screws for

later use.

Notes:

• There is a slight curve to

this style of freezer

handle.

• For proper installation, be

sure handle is oriented as

shown.

Front Mount Plastic Freezer Handle

ToInstall:

1. Align door handle

clips to the studs

attached to the

freezer door.

2. Ensure the large

hole in the

mounting clip is

positioned to the

right on both ends

of the handle.

3. Rotate the handle so that the handle is flat against

the door.

4. Grasp the handle firmly and slide handle to the

right.

To Remove:

1. With both hands, firmly grasp the handle toward

the right side.

2. Slide toward the left,lift and remove from the

surface.

Handle

Clip Handle

Base

Door Stud

Installation

To Remove:

• Loosen set screws in handle using 3⁄32”Allen

wrench.

• Repeat the procedure on all screws.

To Replace:

• Align handle with the mounting posts.

•Apply upward pressure to the handle and hold.

•Fully tighten all set screws to secure handle in

place.

Metal Handle

Materials Needed:

•3⁄32”Allen wrench

• Gloves to protect hands

Note: Metal handles can scratch doors.

Connecting the Water Supply

(select models)

To reduce the risk of injury or death, follow

basic precautions, including the following:

• Read all instructions before installing ice maker.

•Do not attempt installation if instructions are not

understood or if they are beyond personal skill

level.

•Observe all local codes and ordinances.

•Do not service ice maker unless specifically

recommended in Use & Care Guide or published

user-repair instructions.

• Disconnect power to refrigerator before installing

ice maker.

• Water damage due to an improper water

connection may cause mold/mildew growth.

Clean up spills or leakage immediately.

WARNING

To avoid property damage or possible injury,

follow basic precautions, including the

following:

• Consult a plumber to connect 1⁄4”O.D. copper

tubing to household plumbing to assure

compliance with local codes and ordinances.

• Confirm water pressure to water valve is between

35 and 100 pounds per square inch. 20 pounds

per square inch if there is not a water filter.

•Do not use a self-piercing, or 3⁄16”saddle valve.

Both reduce water flow and can become clogged

over time, and may cause leaks if repair is

attempted.

• Tighten nuts by hand to prevent cross threading.

Finish tightening nutswith pliers and wrenches.

Do not over-tighten.

• Wait 2-3 hours before placing refrigerator into final

position to check and correct any water leaks.

Recheck for leaks after 24 hours.

• Verify the copper tubing under the sleeve is

smooth and free from defects. Do not reuse an

old sleeve.

CAUTION

Installation

Materials Needed:

•1⁄4”outer diameter flexible copper tubing

• Shut-off valve (requires a 1⁄4”hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench (2)

•1⁄4”hex nut driver

Notes:

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8’ to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with

copper tubing (minimum 2’

diameter). Avoid kinks in the

copper tubing when

bending the service loop. Do

not use plastic tubing.

2. Remove plastic cap from water valve

inlet port.

3. Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old

sleeve. The nut and sleeve are

provided in the Use and Care

packet.

4. Place end of copper tubing into

water valve inlet port. Shape

tubing slightly. Do not kink – so

that tubing feeds straight into inlet

port.

2’ diameter

minimum

Installation

5. Slide brass nut over sleeve and screw

nut into inlet port.

Place adjustable wrench on nut

(1) attached to plastic waterline

and maintain position.

Using second adjustable wrench

turn the lower nut (2)

counterclockwise and fully

tighten while holding the upper

nut in place.

Important: Do not over-tighten. Cross-threading

may occur.

6. Pull on tubing to confirm

connection is secure.

Connect tubing to frame

with water tubing clamp (C)

and turn on water supply.

Check for leaks and correct

if necessary. Continue to

observe the water supply

connection for two to three

hours prior to moving the

refrigerator to its permanent

location.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

1. Create service loop with copper

tubing (minimum 2’ diameter).

Avoid kinks in the copper tubing

when bending the service loop.

Do not use plastic tubing.

2. Remove plastic cap from water

valve inlet port.

3. Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use old sleeve.

The nut and the sleeve are

provided in the use and care

packet.

4. Place end of copper

tubing into water valve

inlet port. Shape tubing

slightly. Do not kink –

so that tubing feeds straight into inlet

port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

Important: Do not over-tighten. Cross

threading may occur.

6. Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn on

water supply.Check for leaks and correct

if necessary. Continue to observe the

water supply connection for two to three

hours prior to moving the refrigerator

to its permanent location.

7. Monitor water connection for 24 hours.

Correct leaks, if necessary.

2’ diameter

minimum

Alternate connection (select models)

Materials Needed:

•1⁄4”outer diameter flexible copper tubing

• Shut-off valve (requires a 1⁄4”hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench

•1⁄4”hex nut driver

Notes:

• Use copper tubing only for installation. Plastic is

less durable and can cause damage.

• Add 8’ to tubing length needed to reach water

supply for creation of service loop.

Andere Handbücher für MBF2256KEB - Bottom Freezer Refridgerator

Inhaltsverzeichnis

Andere Maytag Kühlschrank Handbücher

Maytag

Maytag MFI2266AEB - Ice2O Series Refrigerator Bedienungsanleitung

Maytag

Maytag MTB1954MEB - 18.9 Cuubic Foot Top Freezer... Bedienungsanleitung

Maytag

Maytag MSD2554VEA - 25 cu. Ft. Refrigerator Fehlerbehebungshandbuch

Maytag

Maytag GC2224GEKX Bedienungsanleitung

Maytag

Maytag MRT118FZEM Bedienungsanleitung

Maytag

Maytag ATB1821AR series Bedienungsanleitung

Maytag

Maytag MCB2256HE Bedienungsanleitung

Maytag

Maytag W10216897A Bedienungsanleitung

Maytag

Maytag Ice2O Series Bedienungsanleitung

Maytag

Maytag MFX2876DRM Bedienungsanleitung

Maytag

Maytag MZD2663KES - Wide-By-Side Refrigerator Handbuch

Maytag

Maytag MTB1954EES Bedienungsanleitung

Maytag

Maytag MSD2254VEB - 22.0 cu. Ft. Refrigerator Bedienungsanleitung

Maytag

Maytag MURM24FWBS Bedienungsanleitung

Maytag

Maytag MSD2554VE Bedienungsanleitung

Maytag

Maytag MBR2262KES - 21.9 cu. Ft. Bottom-Freezer... Handbuch

Maytag

Maytag PBF1951KEW - 30" Bottom Freezer Refrigerator Bedienungsanleitung

Maytag

Maytag MFD2562VEB - 25 cu. Ft Bottom Mount... Montageanleitung

Maytag

Maytag MTF1842EEB00 Fehlerbehebungshandbuch

Maytag

Maytag Ice2O MFI2665XE Bedienungsanleitung

Maytag

Maytag 23inch Bedienungsanleitung

Maytag

Maytag MBR2556KES - 25.1 cu. Ft. Bottom-Freezer... Benutzerhandbuch

Maytag

Maytag MZD2669KE Series Bedienungsanleitung

Maytag

Maytag W10558103A Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung