Maytag MFD2560HEW Bedienungsanleitung

M/ AG French Door

_-16

Form No. A/O3/O4

Temperature Controls .................... 10

Fresh Food Features ................ 11-13

Freezer Features ............................. 13

Ice And Water ................................... 14

Part No. 12828104 www.maytag.com

.................... 17-19

Care and Cleaning ................... 20-23

Operating Sounds .......................... 24

Troubleshooting ........................ 25-27

Warranty & Service ........................ 29

Guide d'utUisation et

d'entretien ........................................ 30

Guia de uso y cuidado .................. 59

Litho U.S.A.

ImportnntSnfetyInstructions

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact your dealer, distributor, service agent or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electrical shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obligation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground} prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

ImportnntSnfetyInstructions

SAVE THESE INSTRUCTIONS

Installation

Your refrigerator was packed carefully for shipment.

Remove and discard shelf packaging and tape. Do not

remove the serial plate.

Location

• Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

• Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction may

occur at this temperature.

•Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow '/2"space at top and '/2"space behind the machine

compartment cover (located in the rear) for proper air

circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a recess

where the top of the refrigerator is completely covered,

use distance from floor to top of hinge cap to verify

proper clearance.

Leveling

To enhance the appearance and maintain performance,

the refrigerator should be level.

Note

• Complete any required door reversal, panel

installation and/or a water supply connection,

before leveling.

Materials Needed

•3/8"hex head driver

• Carpenter's level

1. Remove toe grille.

• Grasp firmly and pull outward

to unclip.

2. Remove bottom hinge cover(s).

• Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an upright

position is not possible, lay refrigerator on its back.

Allow refrigerator to sit upright for approximately 30

minutes before plugging it in to assure oil returns to

the compressor. Plugging the refrigerator in

immediately may cause damage to internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening restraints

may dent or damage outside finish.

Notch

Location

• Use slight pressure to pry the

cover loose.

• Continue to maintain

downward pressure to the

notched side of the cover while

swingmg it off.

3. Using hex head driver, turn the front adjustment

screws (A) on each side to raise or lower the front

of the refrigerator.

C C

Installation

/4. Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

5. Using the carpenter's level, make sure front of

refrigerator is '/4"(6 ram) or '/2bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

6. Turn stabilizing legs (C) clockwise until firmly

against floor.

7. Turn adjustment screws (A) counterclockwise to

allow the full weight of the refrigerator to rest on

the stabilizing legs.

8. Replace hinge cover(s).

• Position cover into the outer edge of the hinge.

• Swing the cover toward the cabinet and snap it

into place.

9. Replace the toe grille.

Note

• For proper reinstallation, ensure the "top" marking

on the interior of the toe grille is oriented correctly.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

Unplug power cord from power source.

Remove toe grille and bottom hinge

cover(s) (see page 3).

Remove top hinge cover from

refrigerator door by removing Phillips

screw and retain screw and cover for

later use.

Unscrew %6"hex head screws from

top hinge to remove hinge and retain

all screws for later use.

Lift right side refrigerator door from " "

center hinge pin. Remove door

closure from center hinge pin on

the right side and retain for later

use.

Disconnect wire harness on top

of left side refrigerator door top

hinge.

Release two-pin connector by

pressing junction point with a

flat blade screwdriver or

fingernail.

Green ground wire remains

attached to the hinge.

Unscrew 6/,_..hex head screws from

top hinge to remove hinge and retain

for later use.

Lift left side refrigerator door, along

with top hinge, from center hinge pin.

Remove center hinge pin with a _/,_..

hex head driver and retain hinge pin

for later use.

Remove Phillips screws to remove

right and left hinges and retain all

screws for later use.

Remove both stabilizing brackets

with %" hex head driver and retain

screws for later use.

right

stde

door

closure

Installation

Pullout Freezer Drawer To Install:

1. Pull both rails out to full

extension.

2. While supporting door front,

hook supports into tabs

located on inside of rail.

3. Lower door front into

final position.

To Remove:

1. Pull drawer open to full extension.

2. Pull upper basket out to full extension and lift out

to remove.

Lift lower basket straight up and out to remove.

On each side rail is a

basket cradle with two snap

attachments. To release

each cradle, unlatch the

snaps by pushing them

inward, away from the side

rail system. Lift the cradles

off of the rails.

.Lift top of drawer front

to unhook supports

from rail system. Lift

door front out to

remove.

4. Place the basket cradles back onto the side rails.

Align snaps with the slots on the side rails and

press each snap towards the rail until it clicks.

5. With rails pulled out to full extension, set the

basket straight down into the basket cradles.

Basket cradle

snap attachments

6. Slide upper basket into freezer. Make sure that rear

of basket hooks behind rail catch.

Installation

Door ReinstaHation

1. Install hinge assemblies:

Install top hinge loosely with %_"hex head

screws.

Install center hinge with Phillips

screws.

2. Place hinge side of refrigerator door

on center hinge pin.

3. While holding refrigerator door

upright, tighten down top hinge

with -%_"hex head ddver.

/4. Reconnect two-pin connector.

5. Replace top hinge cover&

3. Ensure the handle clips are

positioned slightly above the

door tabs.

4. Rotate the handle so that the

handle is flat against the door.

5. Push the handle down against the

upper door tab just enough to

allow it to hang unsupported.

Handle

Door

Tab

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

Remove and discard handle packaging and tape.

Front Mount Handle

Materiams Needed

Gloves to protect hands

Phillips screwdriver

Plastic door removal card (or h2" thick plastic card},

retain the card

Attach E×tensions to Handle:

__-J

1. Align handle and //j'.

extension as shown. _,,_X .J/

2. Place extension in _,_-:--_,_Y-

handle opening. --\_\_._: "

3. Apply slight pressure X

to both sides of the extension piece.

4, Slide extension until [t stops on inside edge of

handle,

To Unstall:

1. The handles are to be oriented

as shown.

2. Align front mount door handle

clip with the door tabs.

Align bottom of handle with lower

door tab. Press upper handle end to

door surface and firmly grasp lower

end of handle. Gently slide handle

upward until bottom of handle

settles on door surface, then

reverse direction, sliding downward

to almost engaging tab with clip.

Grasp the handle firmly and slide

down until it clicks. The audible

click indicates fastening clips are

securely interlocked.

To Remove:

1. Flex the handle away from the door

panel. Simultaneously place door

handle removal card underneath

the base of the lower handle. Insert

the card to the line or until it stops.

2. Grasp the lower part of the handle

firmly and lift to remove.

Installation

Freezer Handle

Materials Needed

•Gloves to protect hands.

• Phillips screwdriver.

• Plastic handle removal card (or '/_2"thick plastic

card). Retain the card.

Notes

• There is a slight curve to

the freezer handle.

• For proper installation, be

sure handle is oriented as

shown.

To Install:

1. Align door handle clips slightly to the left of the

tabs attached to the freezer door.

2. Rotate the handle so the left base is flat against

the door.

Handle Door

While firmly supporting the left handle base against

the door, align the right base of the handle with the

right tabs that are attached to the door.

Now, while firmly holding the handle at the left and

right bases, gently slide the handle towards the

right until the right base settles in. The handle

should now be flat against the face of the freezer

door at both the left and right bases.

With hands still firmly keeping the handle flat

against the freezer door, you may have to reverse

directions momentarily to assure clip/tab

engagement. Then firmly slide the handle to the

right until it clicks. The audible "click" indicates

that the fastening clips are securely interlocked.

To Remove:

At the right end, flex the handle base away from

the surface of the freezer drawer. Simultaneously

slide the door handle removal card that came with

your refrigerator under the right side base of the

handle. Slide the card to the line indication or until

it stops, which will be approximately 1'f2".

With both hands, firmly grasp the handle towards

the right base.

Slide towards the left, lift and remove from the

surface.

3. Push the left handle

base against the left

door tab and slightly

to the right, just

enough to allow it to

hang unsupported.

Installation

Connecting the Water Supply Materials Needed

•Y4"outer diameter flexible copper tubing

• Shut-off valve (requires a X" hole to be drilled into

water supply line before valve attachment)

• Adjustable wrench

• '/_"hex nut driver

Note

• You should only use copper tubing for installation.

Plastic is less durable and can cause damage.

• Add 8'

supply to tubing length needed to reach water

for creation of service loop.

Create service loop with copper

tubing (minimum 2' diamete0.

Avoid kinks in the copper tubing

when bending it into a service

loop. Do not use plastic tubing.

2' diameter

minimum

Remove plastic cap from water valve inlet

port.

Place brass nut (A) and sleeve (B)

on copper tube end as illustrated. A

Reminder: Do not use an old

sleeve. The nut and sleeve are

provided in the use and care

packet.

Place end of copper tubing into water

valve inlet port. Shape tubing slightly. Do

not kink - so that tubing feeds straight

into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

[MPORTANT: Do not overdghten. Cross

threading may occur.

Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn on

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

for two to three hours prior to moving

the refrigerator to its permanent

location.

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

Installation

Opening and Closing Your

Fresh Food Doors

Your new refrigerator is uniquely designed with two

fresh food doors. Either door can be opened or closed

independently of one another.

There is a vertically-hinged section on the left fresh

food door. When the left door is closed, the hinged

section automatically forms a seal between the two

doors when both doors are closed.

When the left door is opened, the hinged seal

automatically folds inward so that it is out of the way.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Maytag Kühlschrank Handbücher

Maytag

Maytag MFX2571XEB Montageanleitung

Maytag

Maytag Side by Side Refrigerator Bedienungsanleitung

Maytag

Maytag ASD2275BRW00 Kurzanleitung

Maytag

Maytag RTC1500AAL-CH01A Betriebsanleitung

Maytag

Maytag MTB2254EES Bedienungsanleitung

Maytag

Maytag MSC21C6MDM00 Bedienungsanleitung

Maytag

Maytag Performa MBF1956HES Bedienungsanleitung

Maytag

Maytag MBF1956KEB11 Fehlerbehebungshandbuch

Maytag

Maytag MURM24FWBS Montageanleitung

Maytag

Maytag MFI2067AES - 20.0 cu. Ft Bedienungsanleitung

Maytag

Maytag MFT2672AEM Bedienungsanleitung

Maytag

Maytag MFX2570AEW0 Bedienungsanleitung

Maytag

Maytag Built-in Refrigeration Bedienungsanleitung

Maytag

Maytag MTB2254ME - 22 cu. Ft. Refrigerator Bedienungsanleitung

Maytag

Maytag MFT2771XEM1 Bedienungsanleitung

Maytag

Maytag W10321480A Bedienungsanleitung

Maytag

Maytag Performa 111208-1 Bedienungsanleitung

Maytag

Maytag MFI2665XEM Montageanleitung

Maytag

Maytag AON-A71 Bedienungsanleitung

Maytag

Maytag MFI2569YEM Handbuch

Maytag

Maytag MFI2570FEZ Bedienungsanleitung

Maytag

Maytag MSD2258KES Bedienungsanleitung

Maytag

Maytag M1TXEMMWB00 Fehlerbehebungshandbuch

Maytag

Maytag M1TXEMMWS - 21.0 cu. Ft. Refrigerator Montageanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung