Maytag MSD2357HES Bedienungsanleitung

Side by Side

ice and Water=.,

.............

24_27

Water Filter .......... " ............... ,,,,,,, 13=15

Food Storage Tips ...................... 16=18 _¢J Warranty & Service ............................ 31

Care and Cleaning ..................... 19=22 Guide d'utilisation

et d'entretien ............................... 32

Operating Sounds ............................. 23 Guia de uso y cuidado ..................... 64

Form No. A/el/e6 Part No. 12842130 Litho U.S.A.

Important$afe

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounding plug for your protection against possible

electrical shock hazards. It must be plugged into a

grounding receptacle. Where a standard two-prong

wall receptacle is encountered, it is the personal

responsibility and obligation of the customer to have it

replaced with a properly grounded three-prong wall

receptacle. Do not under any circumstances, cut or

remove the third (ground) prong from the power cord.

Do not use an adapter plug.

Power supply cord with

three-prong grounding plug

Grounding type

wall receptacle

Important$afe_

SAVE THESE iNSTRUCTiONS

Location

•Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material.

•Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (43° C). Malfunction

may occur at this temperature.

• Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, allow '/z"space at top

and '/2"space behind machine compartment cover

(located in the tea0 for proper air circulation. If the

refrigerator is placed with the door hinge side against

a wall, you may want to allow additional space so the

door can be opened wider.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

IMPORTANT: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely

covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

•NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its

back. Allow refrigerator to sit upright for

approximately 30 minutes before plugging it in to

assure oil returns to the compressor. Plugging

refrigerator in immediately may cause damage to

internal parts.

•Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not overtighten. Overtightening

restraints may dent or damage outside finish.

Door and Hinge Removal

Some installations require door removal to get

refrigerator to final location.

1. Unplug power cord from power source.

2. Remove toe grille and bottom bracket covers (see

page 6).

• Open both doors 180°, or as wide as possible.

For ice and water dispensing models only:

Remove the left side bracket cover by carefully

pulling the water line to pry the cover loose. Then

continue to maintain downward pressure to the

notched side of the cover while swinging it off

(see page 6).

Note

•For refrigerators in operation, shut off water before

removing water line from the door.

To Disconnect the Water Line:

• Push in white collar (A) and hold.

•Pull the door-side tube from the connector (B).

To Reconnect the Water Line:

• Firmly push tube %" into the connector. Use

lines on the tube as a guide for full insertion.

• If tube end is damaged, cut off 5/8"before

reconnecting.

• If leaking occurs, reconnect the line.

Replacing the Doors

•To replace the doors, follow the steps in Door and

Hinge Removal in reverse order.

iMPORTANT: If water line tube end is damaged, cut

off 5/?,before reconnecting.

3. Close doors.

4. Remove top hinge covers by

removing Phillips screws.

5. Unscrew _,6" hex head screws from

top hinges.

For ice and water

dispensing models only:

•Do not remove screw

connecting green ground

wire.

6. For ice and water

dispensing models only: Detach ma=n wire

connector harness and red wire harness.

• To detach main wire

harness, use a flat blade

tool or fingernail to press

junction point between two

connectors to release.

• To detach red wire harness,

press tab on underside of

connector to release.

7. Remove top hinges along with

doors.

8. Remove bottom hinges with a _/?'hex head driver.

Connecting the Water Supply

([select models)

Materials Needed

* '/4"outer diameter flexible copper tubing

* Shut-off valve (requires a '/4"hole to be drilled into

water supply line before valve attachment)

. Adjustable wrench

.'/_"hex nut driver

Note

•Add 8' to tubing length needed to reach water

supply for creation of service loop.

1. Create service loop with copper

tubing (minimum 2' diameter).

Avoid kinks in the copper tubing

when bending the service loop.

2. Remove plastic cap from water valve

inlet port.

3. Place brass nut (A) and

sleeve (B) on copper

tube end as illustrated.

(Do not use old sleeve.)

4. Place end of copper tubing into water

valve inlet port. Shape tubing slightly. Do

not kink - so that tubing feeds straight

into inlet port.

5. Slide brass nut over sleeve and screw nut

into inlet port. Tighten nut with wrench.

IMPORTANT: Do not overtighten. Cross

threading may occur.

.Pull on tubing to confirm connection is

secure. Connect tubing to frame with

water tubing clamp (C) and turn on

water supply. Check for leaks and

correct if necessary. Continue to

observe the water supply connection

for two to three hours prior to moving

the refrigerator to its permanent

location.

7. Monitor water connection for 2/4 hours.

Correct leaks, if necessary.

Handle installation

If not installed, the handle is located in the interior of the

fresh food section or attached to the back of your refrig-

erator. Remove and discard handle packaging and tape.

Front Mount Handle

Materials Needed

•Gloves to protect hands

•Phillips screwdriver

• Plastic door handle removal card (or '/32"thick plastic

card), retain the card

To install:

1. The handles are to be oriented

as shown.

Align front mount door handle

clip with the door tabs.

Ensure the

handle clips

are positioned

slightly above

the door tabs.

/4. Rotate the handle so that the

handle is flat against the door.

5. Push the handle down against the upper

door tab just enough to allow it to hang

unsupported.

n otto o,h n ewthowe1

tab. Press upper handle end to door

surface and firmly grasp lower end of

handle. Gently slide handle upward until

bottom of handle settles on door surface,

then reverse direction, sliding down-

ward to almost engaging tab with clip.

Grasp the handle firmly and slide down

until it clicks. The audible click indicates

fastening clips are securely interlocked.

To Remove:

1. Flex the handle away from the door panel.

Simultaneously place door handle removal card

underneaththebaseofthelower

handle.Insertthecardtothelineor

untilit stops.

2.Graspthelowerpartofthehandle

firmlyandliftto remove.

Leveling Note ]

• Some models only have adjustment screws "A"

Select models also have rear adjustment screws (B).

Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

Using the carpenter's level, make sure front of

refrigerator is '/4"(6 ram) or '/_bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

To enhance the appearance and maintain performance,

the refrigerator should be level.

Note

• Complete any required panel installation and/or a

water supply connection, before leveling.

Materials Needed

•3/8"hex head driver

• Carpenter's level

1. Remove toe grille.

• Grasp firmly and pull bottom outward to unclip.

2. Remove bottom bracket cover(s).

• Place the eraser end of a pencil or similar blunt

tool in the cover notch.

Notch

Location

•Use slight pressure to pry the

cover loose.

• Continue to maintain downward

pressure to the notched side of

the cover while swinging it off.

3. Using hex head driver, turn both of the front

adjustment screws (A) clockwise to raise and

counterclockwise to lower the front of the

refrigerator.

6_ If required, correct rocking of refrigerator by turning

rear adjustment screw clockwise to raise rocking

corner. If doors are uneven, do the following:

• Determine which door needs to

be raised.

• Turn front roller adjustment

screw (A) clockwise to raise

front corner of door.

• If one refrigerator door has reached the limit of its

adjustment range and doors are still not level,

raise or lower the opposite door by turning roller

adjustment screw counterclockwise.

•Check with level to verify '/_"tilt to the back for

proper door closure.

• If refrigerator is aligned and stable, replace toe

grille and hinge covers.

7. Replace bracket cover(s).

• Position cover into the outer edge of the hinge.

• Swing the cover toward the cabinet and snap it

into place.

8. Replace the toe grille.

Note

• For proper reinstallation, ensure the "top" marking

on the interior of the toe grille is oriented correctly.

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

fempereture

Dial Temperature Controls

The controls are located at the back left of the

refrigerator compartment.

Note

•The freezer control turns the cooling system on.

Neither section will cool if freezer control is set to

OFE

Initial Control Settings

After plugging the refrigerator in,

set the controls.

*To adjust the controls, turn the

control knob to the left or right

as desired.

*Set the freezer control on/4.

*Set the refrigerator control on/4.

*Let the refrigerator run at least 8

to 12 hours before adding food.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet may be

warm to the touch. This is a normal occurrence that

helps prevent moisture from condensing on the

cabinet. This condition will be more noticeable when

you first start the refrigerator, during hot weather and

after excessive or lengthy door openings.

Adjusting the Controls

24 hours after adding food, you may decide that one

or both compartments should be colder or warmer. If

so, adjust the control(s) as indicated in the

Temperature Control Guide table below. See page 16

for instructions on checking compartment

tern peratu re.

*Except when starting the refrigerator, do not change

either control more than one number at a time.

*Allow 24 hours for temperatures to stabilize.

*Changing either control will have some effect on the

temperature of the other compartment.

Temperature Control Guide

Refrigerator too warm Turn the refrigerator control

to next higher number.

Refrigerator too cold Turn the refrigerator control

to next lower number.

Freezer too warm Turn the freezer control to

next higher number.

Freezer too cold Turn the freezer control to

next lower number.

Turn refrigerator OFF Turn the freezer control to

OFF.

Note

*Turning freezer control to OFF stops cooling in

both compartments. It does not shut off power to

the refrigerator.

Shelves

Your refrigerator has either spill-retaining or non-

sealed shelves. Spill-retaining shelves have a sealed

edge which contains spills and allows for easier clean

up.

To Remove aShelf:

•Slightly tilt up the

front and lift up the

rear of the shelf, then

pull the shelf straight

out.

To Lock the Shelf into Another Position:

*Tilt up the front edge of the shelf.

*Insert the hooks into the desired frame openings and

let the shelf settle into place.

. Be sure the shelf is securely locked at the rear.

The Crisper Top serves as the lower fresh food shelf.

To Remove the Crisper Top:

* Place hand under the frame to push up the glass. Lift

glass out.

To install:

• Repeat above instructions in reverse order.

Dairy Center

The Dairy Center provides convenient

door storage for spreadable items such

as butter and margarine. On select

models, this compartment can be

moved to several different locations to

accommodate storage needs.

To Remove:

*Slide dairy center up and pull out.

To Install:

*Slide assembly in and down so that the hooks are

firmly seated on the door liner.

To Remove Dairy Door:

*Press in sides of dairy door and pull out.

To install Dairy Door:

*Slide sides of dairy door inside dairy center until

hinge points snap into place.

Door Buckets

Door Buckets can be moved to meet

individual storage needs.

To Remove:

• Lift bucket up and pull straight

out.

To install:

•Place bucket in desired door liner retainer, push

down until bucket stops.

Storage Drawers

The Crisper Drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Shelves and Baskets

Fixed Freezer Shelf

To Remove Clip-mounted Shelves:

• Lift shelf from wall mounting

clips and pull left side of shelf

out of wall mounting holes.

To Install Clip-mounted Shelves:

•Place left side of shelf in mounting holes and press

down into wall mounting clips.

Shelves

Shelves can be removed to meet individual storage

needs.

To Remove Shelf:

• Snap right side of shelf up from

cabinet railing and slide to right.

To install Shelf:

•Replace shelf in left side cabinet railing. Snap shelf

into right side cabinet railing.

Baskets

Baskets [style may vary) slide out for

easy access to items in back.

To Remove:

• Pull out to its full extension. Lift

up front of basket and remove.

To install:

•Slide basket into cabinet railing. Lift up front of

basket, and slide to the back of refrigerator.

ice Storage Bin

The Ice Storage Bin is located below the automatic

ice maker.

To Remove:

• Raise ice maker arm to deactivate ice maker. Lift

front of bin and pull out to its full extension. Lift up

front of bin and remove.

To Install:

• Slide bin into railing below ice maker until bin locks

into place. Drop ice maker arm to activate ice maker.

IMPORTANT: Ice bin must be locked in place for

proper ice dispensing. Turn auger driver behind bin

counterclockwise (as shown) to properly align ice bin

with auger driver.

Door Storage

Adjustable Door Buckets

Door Buckets can be moved to meet individual

storage needs.

To Remove:

•Lift the door bucket up until it clears the

retainers on the door liner, then

pull the door bucket straight out.

To Install:

•Slide bucket in above desired door liner retainer and

push down until bucket stops.

Fixed Door Bucket

Inch=dispenser models)

The Fixed Door Bucket is located in

the upper section of the freezer door.

IMPORTANT: Fixed door bucket is not

adjustable. If bucket is removed, freezer

light will not deactivate when door is

closed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Maytag Kühlschrank Handbücher

Maytag

Maytag MFW2055YEB00 Bedienungsanleitung

Maytag

Maytag MFI2269VE Series Stücklistenhandbuch

Maytag

Maytag MFI2266AEU Bedienungsanleitung

Maytag

Maytag MFC2061HES - 20 cu. Ft Bedienungsanleitung

Maytag

Maytag MBF2556KEB - 25.1 cu. Ft. Bottom Freezer... Handbuch

Maytag

Maytag MFX2571XEB Montageanleitung

Maytag

Maytag MBF1958WES - 19.0 cu. Ft. Bottom Freezer... Bedienungsanleitung

Maytag

Maytag MBF2262HEW - 22 cu. Ft. Bottom Freezer... Bedienungsanleitung

Maytag

Maytag MBB1952HEW14 Fehlerbehebungshandbuch

Maytag

Maytag MFI2269VEQ - 22.0 cu. Ft. Refrigerator Montageanleitung

Maytag

Maytag MFI226AE Series Allgemeine Anweisungen

Maytag

Maytag GB1924PEKS Bedienungsanleitung

Maytag

Maytag MFB2055YEM Bedienungsanleitung

Maytag

Maytag RSW22E0CAE/DM35A Bedienungsanleitung

Maytag

Maytag MBR1956KES - Bottom Freezer Refridgerator Benutzerhandbuch

Maytag

Maytag 913478 Bedienungsanleitung

Maytag

Maytag MBF2256KEW - Bottom Freezer Refridgerator Bedienungsanleitung

Maytag

Maytag RTD1700AAL Bedienungsanleitung

Maytag

Maytag MBL1957VES2 Bedienungsanleitung

Maytag

Maytag 12828121 Bedienungsanleitung

Maytag

Maytag MFD2562VEW - 25 cu. Ft. Bottom Mount... Bedienungsanleitung

Maytag

Maytag MSD2254VEB - 22.0 cu. Ft. Refrigerator Bedienungsanleitung

Maytag

Maytag MBB1957VEB10 Bedienungsanleitung

Maytag

Maytag MSD2274VEM - 21.8 cu. Ft. Refrigerator Montageanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung