Maytronics Hybrid Bedienungsanleitung

8151170

Operating Instructions

Hybrid - Robotic Suction Pool Cleaner



Contents

The Hybrid Suction Cleaner .............................2

Parts..................................................................2

Warnings...........................................................3

Speciﬁcations ...................................................3

Water conditions ..............................................3

Pool Preparation...............................................3

Setup ................................................................3

Cleaning Process ..............................................6

Clean the Leaf Canister ....................................6

Removal from the Pool and Storage ................7

Troubleshooting ...............................................7

2Hybrid - Robotic Suction Pool Cleaner |Operating Instructions

Hybrid - Robotic Suction Pool Cleaner

Operating Instructions



The Hybrid Suction Cleaner

The Hybrid Cleaner is powered by the pool pump. For successful cleaning results, make sure that

you connect the cleaner properly to the pool system.

Follow the instructions in this booklet for easy, efﬁcient, and safe operation.



Parts

The Hybrid Cleaner kit includes:

Hybrid Cleaner

Hose Sections (1.17m/3.83ft x 10)

Flow Indicator

90° Adapter

Float

Skimmer Adapter

Automatic Safety Valve

Leaf Canister (optional)

For proper operation, the hose must be long

enough to reach from its pool connection to

the most distant edge of the pool, plus two

extra sections (Drawing A). If needed, you

can purchase additional hose sections from

your supplier. Replacement parts are also

available.

min max

(Optional)

Skimmer

Pool

Two extra

hose sections

Hybrid - Robotic Suction Pool Cleaner |Operating Instructions 3



Warnings

• Do not enter the pool while the cleaner is working.

• The manufacturer is not responsible for any damage to the external pump.



Speciﬁcations

• Wight – 4.5 kg / 9.9lb

• Hose length – 10 Hoses of 1.17m / 3.83ft

• Required water ﬂow – 5-8m



Water conditions

• Chlorine – Max 4ppm

• pH – 7.0-7.8

• NaCl – Max – 5000ppm

• Temperature – 6-34°C / 43-93°F

NOTE:

An optional Leaf Canister is also available for purchase from your supplier.

The Leaf Canister traps leaves and other large debris, preventing blockage of the

pool ﬁlter system. For maximum energy, backwash savings and environmentally

friendly operation, we recommend using the Leaf Canister.



Pool Preparation

To prepare the pool for cleaning:

Remove any large

objects that might

interfere with the

cleaner’s operation.

Make sure that the

water level reaches

the skimmers.

Backwash the pool

ﬁlter and make sure

that suction pressure

is sufﬁcient, as

recommended by the pump manufacturer.



Setup

Connect the Hose

The Hybrid Cleaner connects to the pump of your pool, either by a built-in dedicated suction line or

through one of the pool skimmers.

Connect the Hose Sections in the pool under water.

Switch the pool pump OFF.

Insert the ﬂexible Skimmer Adapter (only if needed) into the suction line opening and make sure

to connect the Automatic Safety Valve. (Allows water ﬂow into the pump in case the Cleaner is

blocked by a forgien object).

CAUTION

Connecting to Skimmer Connecting to Suction Line

First

Hose

Section

Safety Valve

Suction

Line

Skimmer

Adapter

First

Hose

Section

Safety Valve

Skimmer

Adapter

Suction Line

4Hybrid - Robotic Suction Pool Cleaner |Operating Instructions

If connecting to a

skimmer, choose

the skimmer located

closest to the center

of the longest pool

wall.

Remove the skimmer

basket and push the

male end of a Hose

Section into the

Safety Valve, using a

twisting motion.

If using a shallow skimmer, connect the 90° Adapter to the automatic Safety Valve before

connecting the Hose Section to ensure proper suction ﬂow

(Drawing C).

Continue connecting additional sections until the hose is long enough to reach from its pool

connection to the most distant edge of the pool, plus two extra sections.

Make sure to add the Float 40 cm (1.30 Ft) above the Hybrid Cleaner on the last Hose Section

(Drawing F).

Install the optional Leaf Canister between the ﬁrst and second Hose Sections under water, as

well.

CAUTION

Air trapped in the hose can damage your pump!

Check Flow

The Hybrid Cleaner operates on the suction power of the pool system. Satisfactory ﬂow is important

to ensure proper cleaning and to prevent damage to the Hybrid Cleaner.

NOTE:

Make sure to stop operation of the pool drain while the Hybrid Cleaner

is working.

To make sure that ﬂow is satisfactory:

Completely immerse the hose in the

water and remove any trapped air.

Connect the Flow Indicator to the free

end of the hose, under water level.

Switch the pool pump ON.

Check the Flow Indicator (Drawing D).

Make sure that the indicator is between

MIN. and MAX. If the indicator is

not in the satisfactory range, there

may be air trapped in the hose. Wait

approximately two minutes while the

pump continues to operate to remove

any trapped air.

If the indicator remains outside the

satisfactory range, correct unsatisfactory ﬂow according to the instructions in the following table.

After each action, check ﬂow with the Flow Indicator. If ﬂow is still unsatisfactory, proceed to the

next action.

minmax

Indicator

Deep Skimmer Shalow Skimmer

Hose

Safety Valve

Hose

Skimmer Adapter Skimmer Adapter

Safety Valve

90° Adapter

Vacum

Chamber

Vacum

Chamber

Hybrid - Robotic Suction Pool Cleaner |Operating Instructions 5

CAUTION

Operating above the MAX. may damage the Hybrid Cleaner.

Table 1: Flow Indicator

Flow Indication Action

In satisfactory range

Connect the Hybrid Cleaner and begin the cleaning process.

Below MIN.

To correct the ﬂow do one or more of the following:

• Make sure that the water level of the pool reaches the skimmer.

• Check that the hose is not twisted or bent near the pool connection.

If it is, use the 90° Adapter.

• Close unused skimmers or main drain. Make sure that the skimmer used

for the Hybrid Cleaner is fully opened.

• Remove trapped air from the hose and Hybrid Cleaner.

• Tighten connections between Hose Sections.

• Backwash the main ﬁlter and clean the skimmer and pump basket.

Above MAX.

• Open unused skimmers partially (if closed).

• If the Hybrid Cleaner is connected to a dedicated suction line, adjust its

control valve on the pool pump.

• If the Hybrid Cleaner is connected to a skimmer, reduce the suction on

the pool pump.

Connect the Hybrid Cleaner

Make sure that the pool pump is switched OFF.

Disconnect the Flow Indicator (Drawing E).

Make sure the Float is connected on the hose 40 cm

(1.30 ft) above the Hybrid Cleaner.

Make sure that the hose is entirely under the water level

and is ﬁlled with water.

Hold the Hybrid Cleaner by the handle and put it in the

water. Turn the Hybrid Cleaner upside down to remove

any trapped air.

Connect the hose end to the Hybrid Cleaner

(Drawing F). Make sure that the hose is ﬁrmly

connected. Ensure that there is a small space between

the locknut and the pipe.

Realese the Hybrid Cleaner in the pool.

Restart the pump

minmax

6Hybrid - Robotic Suction Pool Cleaner |Operating Instructions



Cleaning Process

The Hybrid Cleaner continues to clean

your pool as long as the pool pump is operating.

The time required to cover all pool surfaces depends

on the pool size. In general, 1-2 hours are sufﬁcient.

During operation, refer to the indicator lights

(Drawing G) on the cleaner to make sure that the

Hybrid Cleaner is functioning properly

(see table below).

Table 2: Indicator Lights

Light Indication

Red (2 sec.) Start of operation

Blue — slow blinking Proper functioning — The Hybrid Cleaner is moving forward.

Blue — fast blinking Proper functioning — The Hybrid Cleaner is making a turn.

Blue and red (2 sec.) Proper functioning — The Hybrid Cleaner identiﬁes a wall.

Red — blinking • Insufﬁcient ﬂow — To correct unsatisfactory ﬂow, refer to Table 1.

• Use the Troubleshooting Guide (Table 3).



Clean the Leaf Canister

Make sure the pump is OFF.

Disconnect the Leaf Canister and hold the

adjacent Hose Section.

Open the lid by turning it anticlockwise

Remove the ﬁlter.

Clean out leaf and other debris (Drawing H).

Rinse the ﬁlter.

Return the ﬁlter and lid.

Connect the Leaf Canister and hose

sections under the water. Make sure to

remove trapped air from the Leaf Canister.

Turn the pump ON.

Canister

Leaf & debris

Filter

Canister

Lid

Hybrid - Robotic Suction Pool Cleaner |Operating Instructions 7



Removal from the Pool and Storage

When you choose to remove the

Hybrid Cleaner from the pool:

Ensure to switch the pool

pump OFF.

Disconnect the Skimmer

Adapter from the suction line

opening.

Disconnect the Safety Valve.

Disconnect the Hose Sections,

pulling them slowly one-by-

one out of the pool.

When you reach the section

connected to the Hybrid

Cleaner, grasp the Hybrid

Cleaner handle and remove

the Hybrid Cleaner from the

pool (Drawing J).

CAUTION

Remove the Hybrid Cleaner from the pool only by its handle!

Store the Hybrid Cleaner and Hose Sections out of

direct sunlight. Do not store the Hybrid Cleaner where

it will be exposed to excessive heat or frost. Make sure

that Hose Sections are in a straight position (Drawing K).

For longer life of the equipment, it is recommended to

rinse the

Hybrid Cleaner

and parts with tap water.

Reopen all skimmers.



Troubleshooting

The Hybrid Cleaner is designed to operate with a minimum of user maintenance.

If a problem does occur, try to determine the cause. Often, the solution is already part of the

standard operating instructions in this booklet. If you cannot solve the problem easily, contact your

supplier.

8Hybrid - Robotic Suction Pool Cleaner |Operating Instructions

The following are typical problems that might occur and possible solutions.

Table 3: Troubleshooting

Symptom Possible Solutions

The Cleaner does not move or moves slowly

(without indicator light)

• Correct insufﬁcient ﬂow. (Refer to Table 1).

• Remove the service opening cover on the Cleaner bottom

(Drawing L) and clean out any trapped debris (Drawing M).

• If a track slipped off the wheels, return it. If this occurs

frequently, purchase replacement tracks from your supplier.

• Contact your supplier for repair.

The Cleaner moves on the back wheels only • Connect additional Hose Sections.

• Correct excessive ﬂow. (Refer to Table 1).

The Cleaner moves on the front wheels only

• Make sure that the Float is in the correct position. (Refer to

“Connect the Cleaner” on page 5).

• Remove the Float from the last Hose Section.

The Cleaner gets stuck on the pool drain • Make sure to stop operation of the pool drain while the

Cleaner is working.

The hose is twisted

1. Turn the pump OFF.

2. Remove the Cleaner from the pool.

3. Open the swivel and clean it (Drawing N).

4. Close the swivel properly and make sure the swivel moves freely.

The Cleaner is turning in circles • The suction is below MIN. (Refer to Table 1).

If does not help, contact your supplier.

Air bubbles at the exit of the water from the

jets, or a noise of air suction

1. Ensure that the hoses are ﬁrmly fastened.

2. Ensure that the Leaf Canister lid is ﬁrmly closed.

Inhaltsverzeichnis

Andere Maytronics Schwimmbadroboter Handbücher

Maytronics

Maytronics Dolphin WAVE 300 XL Bedienungsanleitung

Maytronics

Maytronics Swash CLX Bedienungsanleitung

Maytronics

Maytronics Dolphin Liberty Bedienungsanleitung

Maytronics

Maytronics Dolphin Swash TC Bedienungsanleitung

Maytronics

Maytronics Classic 4-UNI Bedienungsanleitung

Maytronics

Maytronics Dolphin WAVE 50 Bedienungsanleitung

Maytronics

Maytronics 2x2 Gyro Bedienungsanleitung

Maytronics

Maytronics Classic 4-UNI Bedienungsanleitung

Maytronics

Maytronics 8180090 Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

Maytronics

Maytronics Pulit E70 Bedienungsanleitung

Maytronics

Maytronics Dolphin Wave Bedienungsanleitung

Maytronics

Maytronics Classic 4-UNI Bedienungsanleitung

Maytronics

Maytronics Dolphin Liberty Bedienungsanleitung

Maytronics

Maytronics Supreme M4 Bedienungsanleitung

Maytronics

Maytronics Dolphin Classic 12 Bedienungsanleitung

Maytronics

Maytronics Dolphin Mass 13 Bedienungsanleitung

Maytronics

Maytronics Dolphin Liberty 200 Bedienungsanleitung

Maytronics

Maytronics Dolphin Wave 30 Bedienungsanleitung

Maytronics

Maytronics MCC5 Bedienungsanleitung

Maytronics

Maytronics Dolphin Wave Bedienungsanleitung

Maytronics

Maytronics CLASSIC 8D-UNI Bedienungsanleitung

Maytronics

Maytronics Classic 4-UNI Bedienungsanleitung

Maytronics

Maytronics dolphin dx6 Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

AREBOS

AREBOS AR-HE-BSR Produktinformationsblatt

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

Dolphin

Dolphin 2x2 Gyro Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung