Mazda 0000-8F-Z80 Bedienungsanleitung
1
INSTALLATION INSTRUCTIONS
PART NAME :
VEHICLE :
PART NUMBER :
GENUINE Mazda Mobile Start
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this
booklet in order to properly install and use the Mazda Mobile Start. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
• There are several WARNING and CAUTION sections in this booklet concerning safely when installing or
removing the Mazda Mobile Start. Always read and follow them in order to prevent injuries, accidents, and possible
damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if the warning is ignored.
CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored.
• For areas indicating the tightening torque in this instruction manual, tighten to the specified torque using a torque wrench. For
areas in which the tightening torque is indicated inside parentheses ( ), the tightening torque is indicated as a reference value,
however tightening using a torque wrench is not necessary.
• Do not modify the Mazda Mobile Start.
• Do not install the Mazda Mobile Start in any way other than described in the following instructions.
• If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation.
• If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
• Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the
failure of the dealer or installer to follow these instructions.
• To ensure safety and reliability of the work, installation, removal and disposal work must carried out by an Authorized Mazda
Dealership.
• Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
WARNING
090003-33280700
NOTE
To the dealer
•Pleaseturnovertheseinstructionstothecustomerafterinstallation.
To the customer
•Keeptheseinstructionsafterinstallation.Theinstructionsmaybenecessaryfor
installingotheroptionalpartsorremovalofthisaccessory.
•Shouldthevehicleorthisaccessoryberesold,alwaysleavetheseinstructions
withitforthenextowner.
Mazda Mobile Start (MMS)
Mazda CX-3 / Mazda2
0000-8F-Z80 (MMS ECU Kit)
0000-8F-P07 (MMS Harness Kit)
[KD53-V7-629 (Hood Switch)]
2
1. INSTALLATION VIEW
GPS Antenna
Harness (GND)
RES Diagnostic
Connectors
MMS Harness
MMS ECU
GPS & TEL Antenna Cables
TEL Antenna
MMS 2P
Connector
LED
Connector
(Sold separately) Hood switch
(Only for vehicles without theft-deterrent or without i-ELOOP system)
MMS ECU KIT (Part no. 0000-8F-Z80)
Part Part Name Qty. Part Part Name Qty. Part Part Name Qty.
MMS ECU 1Wire Tie
(White 200mm) 5
Urethane
Foam tape
(35 x 115mm)
2
Double-sided
adhesive tape
(25 x 69mm)
1MMS Key Tag 1
Double-sided
adhesive tape
(25 x 25mm)
3
Owner's Manual 1
HARNESS KIT (Part no. 0000-8F-P07)
Part Part Name Qty. Part Part Name Qty. Part Part Name Qty.
MMS Harness 1LED 1«
Harness Clamp 2
FH Protection
Sheet 1GPS Film
Antenna 1GPS Antenna
Cable 1
TEL Film
Antenna 1TEL Antenna
Cable 1Antenna
Template 1
«
Electro tap 1Wire Tie
(White 200mm) 15
Urethane
Foam tape
(35 x 115mm)
4
Installation
Instructions
(ENG/SPA/FRE)
3A-Pillar Clip
(D09W-68162) 1
«
Wire Tie
(Black 200mm)
10
(Sold separately) The following parts are also necessary for installation.
«: Parts marked with a star mark are only used on vehicles without theft-deterrent or without i-ELOOP system.
• Verify that the kit includes all the following parts and that they are free of dirt, scratches, or damage.
Note
• These parts are not necessary for vehicles with theft-deterrent or with i-ELOOP system because the hood
switch is already equipped.
Note
HOOD SWITCH KIT (Part no. KD53-V7-629)
Part Part Name Qty. Part Part Name Qty.
Hood switch 1Screw 1
3
2. PARTS
4
3. BEFORE INSTALLATION
4. CONNECTION USING ELECTRO-TAP
Branch connection procedure using electro tap.
1. Insert the vehicle wiring harness into the electro tap.
2. Fold the electro tap as shown in the figure and lock it.
3. Insert the harness to the end of the electro tap.
4. Firmly press the electro tap terminal using pliers.
5. Fold the electro tap in the direction of the arrow shown in
the gure and lock it.
REQUIRED TOOLS
• 10mm Socket Wrench • Scissors • Torque Wrench • Taped Flathead Screwdriver • Mat
• Electrical Tape • Panel Removal Tool • Soft clean cloth • Squeegee • Glass Cleaner • Nipper
• Pliers • Primer (3M Promoter-4298) • IPA (Isopropyl alcohol) • Phillips Screwdriver
WARNING
When the negative battery cable
is connected during operation, it
may cause electric shock or other
personal injuries. Disconnect the
negative battery cable before
removal/installation.
When connecting or disconnecting
connectors, grasp the connectors,
not the wires. Otherwise a short,
an accident from poor contact or
re may occur.
Do not pull the harness with
excessive force. Doing so can
cause a breakage or a short-
related accident, as well as an
electrical short or re.
Park the vehicle on a level ground.
Set the vehicle on park (P) and
apply the parking brake. Be sure to
turn the ignition switch off, otherwise
the vehicle can move, causing
personal injury or vehicle damage.
CAUTION
Using improper tools may cause
damage and or broken parts.
Use the correct tool for the job.
Wrap protective tape around
screwdrivers and fastener
removal tools to prevent
scratching the vehicle.
Put the removed parts and the
parts in the kit on the protective
sheet to prevent scratches.
Excessive length of wire tie may
interfere with other parts and
cause damage. Cut unnecessary
part up to about 5 mm {0.19 in}
from the xed point.
WORKSHOP
MANUAL
• When the negative battery cable is removed, the clock, radio, trim meters and other memories will be
erased. Make sure to record the content of the memory.
• Refer to the Workshop Manual for removal and installation of vehicle parts. Not following the procedures for
removal/installation in the Workshop Manual could result in an accident or vehicle malfunction.
• Firmly engage the lock part until a click sound is heard.
Caution
1
2
3
4
5
Electro tap
Vehicle wiring harness
Vehicle wiring harness
Harness
Terminal
Firmly press using pliers
Lock
Vehicle wiring harness
5
5. CONNECTION DIAGRAM
MMS ECU
ROOM
Battery
+B
GND
A19
Pin : 1
A10
B1
RDIG
A16
LED
A5
E1
D1
F2
F1
RES LED
Pre connector
RES Connector
GND (M6)
C1
A4
STX
A3
SRX
Pin:2
B2
Pre connector
GPS
GPS
ANTENNA
TEL
TEL
ANTENNA
GPS
TEL
Connector to Connector
MMS Wire
Vehicle Wire
Scotch lock connection
MMS or Vehicle Terminal Insert
VEHICLE
CONNECTOR
**
**
SSU
(Start
/
Stop
control Unit)
Issue A: 05/14/13
PT398-33140
(FEMALE PIN)
(FEMALE PIN)
(MALE PIN)
(FEMALE PIN)
11
20XX-
CONNECTORS
MAZDA MOBILE START (MMS)MMSMAZDA
1
1
2
21
TEL
VEHICLE OPTION CONNECTOR
GPS
D
F
E
C
(MALE PIN)
(MALE PIN)
1
(FEMALE PIN)
1
A
B
(FEMALE PIN)
34
10
5
16 19
(TERMINAL PIN)
6
6. VEHICLE DISASSEMBLY
1. Place the vehicle in park with the parking brake set.
2. Disconnect negative battery terminal and wrap tape
around it to insulate.
Passenger side front trim removal
1. Peel back the Seaming Welt.
2. Remove Cap Nut.
3. Remove Front Side trim.
• Be careful not to damage or lose any parts removed from the vehicle since they will be reused.
Note
Passenger side scuff plate removal
1. Use shaded area to pull (1) and lift (2) Passenger side
Front Scuff Plate to detach Tab A and Clip A.
2. Use shaded area to pull (3) and lift (4) Passenger side
Front Scuff Plate to detach Tab B and Clip B.
Bolttighteningtorque:4.0-6.0N•m(2.9-4.4ft•lbf)
Warning
Front Scuff Plate
Tab A
Hook A
Pin A
Clip A
Pin B
Clip B
Hook B
Tab B
(3)
(4)
(2)
(1)
Vehicle Front
Vehicle front
Cap Nut
Front Side Trim
Front Side Trim
(Backside)
Clip
Weather strip
Clip
Cap Nut
Seaming Welt
Front Side Trim
(Backside)
Clip
Clip
Vehicle Front
Front Side Trim
Negative battery terminal
• When the negative battery cable is connected during
operation, it may cause electric shock or personal
injuries. Disconnect the negative battery cable before
removal / installation.
7
3. Remove Glove box under cover in order of arrows (1-3).
Decoration panel removal
1. Place hand into the glove compartment opening and push
out 3 clips (A) towards the rear of the vehicle.
2. Disengage the remaining clips (A) using the Removal tool.
3. Remove the decoration panel.
• If decoration panel is pulled out on one side, you will damage
it, make sure to pull the whole panel straight out.
Decoration panel
Caution
Vehicle front
Removal tool
Clip A
Decoration panel
Hook A
(2)
(2) (3)
(1)
Pin B Pin B
Hook A
Guide C
Vehicle Front
Vehicle Front
Vehicle Front
Glove box removal
1. Push both sides of the Glove box then pull to dislodge 2
Hooks (B).
2. Remove the Glove box by pulling to dislodge 2 bottom
Hooks (C).
Vehicle front
Hook B
Hook C
Vehicle Front
8
Passenger side lower panel removal
1. Remove 3 Screws and 1 Bolt.
Bolttighteningtorque:2.0-6.0N•m(1.5-4.4ft•lbf)
2. Remove lower panel by pulling in the order of arrows (1-4).
Vehicle front
Vehicle front
Clip
Clip
3. Cut the A-pillar tab connecting part B and the grommet of
the A-pillar tether clip.
4. Remove the A-pillar trim while detaching guides.
Screws
Screw
Clips
Clips
Bolt
Clip B
Clip B
Seaming Welt
(1)
Clip A
Clip B
Clip B
Clip A
Passenger Side A-Pillar
Seaming Welt
A-Pillar trim removal
1. Partially peel back the seaming welt.
2. Dislodge the Passenger side A-pillar trim by pulling on the
shaded area to disengage Clip B and A.
• Do not use excessive force, A-pillar could be damaged.
Caution
A-pillar trim
Guides
Grommet
Nipper
Lead Wire
Clip B
Vehicle front
Part B
Grommet
A-Pillar Trim
Nipper
Tab
Guides
Vehicle front
Vehicle Front
Vehicle Front
(3)
(2)
(4)
(1)
Vehicle Front
Vehicle Front
9
5. Remove the Grommet from the A-pillar by using a flat
head screwdriver by following sequence (1) - (3).
6. Install the new supplied A-pillar tether clip into A-pillar trim
before proceeding.
1. Remove Hood latch cover by using a tape-wrapped flat
head screwdriver to detach the 2 tabs.
2. Remove 2 Bolts from the Fresh air duct.
Bolttighteningtorque:7.8-10.8N•m(5.7-7.9ft•lbf)
• Ensure the new supplied tether clip is used in step 6.
Caution
Grommet
Tape-wrapped athead screwdriver
Tape-wrapped athead screwdriver
(1)
(2)
(3)
Grommet
Tape-wrapped athead screwdriver
Grommet
Hook
Grommet
Hook
(1)
(2)
(3)
Front pillar
inner panel
A-pillar
inner panel
Tape-wrapped athead screwdriver
Tape-wrapped athead screwdriver
Grommet
Tape-wrapped athead screwdriver
Vehicle Front
Fresh air duct
Bolts
Flathead scredriver insertion slot
(1) (2)
Hood latch cover
Flathead screwdriver insertion slot.
7. HOOD SWITCH INSTALLATION
• This procedure is not necessary for vehicles with Theft-deterrent System or with i-ELOOP system because the
hood switch is already installed.
Note
Vehicle Front
Flathead screwdriver
Vehicle Front
10
3. While pressing the tab, lift the relay and fuse block cover
to remove it.
4. Install the Hood switch to the hood latch and secure it
using the supplied Screw.
5. Hook the Hood switch harness to the Hood latch and
secure it using a wire tie (black).
6. Peel the tape backings from the harness clamps and afx
them on the shroud at 2 locations.
Hood Latch
Screw
Wire Tie (Black)
Hood Switch
Relay and fuse block cover
Tab
Harness Clamp
Hood switch
harness
8. Lift the fresh air duct to route the hood switch harness
between fresh air duct and the shroud.
Caution
Shroud
Hood switch harness
Vehicle Front
Vehicle Front
Vehicle Front
Fresh air duct
Vehicle Front
7. Route the hood switch harness securing it to the 2 harness
clamps. Press firmly on clamp tabs to ensure secure
retention of hood switch harness.
• Clean attachment surface using isopropyl alcohol and
cleaning towel.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Mazda Fernstartsystem Handbücher
Mazda
Mazda 0000-8F-H28 Bedienungsanleitung
Mazda
Mazda 2007 CX-7 Bedienungsanleitung
Mazda
Mazda C960 V7 620 Bedienungsanleitung
Mazda
Mazda 3 2004 Bedienungsanleitung
Mazda
Mazda GENUINE C930 V7 620 Programmierhandbuch
Mazda
Mazda MAZDA5 2006 Bedienungsanleitung
Mazda
Mazda 0000-8F-N02B Bedienungsanleitung
Mazda
Mazda GENUINE C930 V7 620 Bedienungsanleitung
Mazda
Mazda Remote Start System MPV Bedienungsanleitung
Mazda
Mazda Remote Start System Bedienungsanleitung
