McDantim Trumix TM-2-HPR+ILLI Bedienungsanleitung

WARNING:

This product can expose you to chemicals including lead and lead compounds, which are known

to the State of California to cause cancer and birth defects or reproduc ve harm. For more

informa on, go to www.P65Warnings.ca.gov

McDantim, Inc. Limited Five Year Warranty

Warranty not valid outside the Con nental USA

If the mechanics of this product are found to be defec ve in materials or workmanship within

ﬁ ve years from the date of purchase, McDantim, Inc. will repair or replace, at its op on, the

defec ve product or component part. If for any reason the original purchaser is unsa sﬁ ed with the

performance of this product, McDantim, Inc. will, at the purchaser’s op on, replace the product or

refund the original sale price upon return of this product to McDantim, Inc. Please retain receipt

for proof of purchase. Proof of purchase is required for any warranty service or claim. Your receipt is

your warranty card.

LIMITED WARRANTY

McDantim, Inc. warrants each product to be free from defects in material and workmanship under

normal use and service for ﬁ ve years from date of sale. The obliga on of McDantim, Inc. under this

warranty is limited to the replacement of defec ve parts. No ce of defec ve parts must be submi ed

to McDantim, Inc. within ﬁ ve year and 15 days of date of sale. This warranty does not cover

shipping, handling, or freight charges.

DISCLAIMER OF WARRANTY

WARRANTY IS INVALID IF PURCHASER FAILS TO PROPERLY OPERATE AND/OR MAINTAIN THE

PRODUCT. THIS WARRANTY IS NOT TRANSFERABLE TO THIRD PARTIES. THIS WARRANTY IS EXPRESSLY

IN LIEU OF ALL OTHER WARRANTIES AND REPRESENTATIONS, EXPRESSED OR IMPLIED EXCEPT AS

STATED ABOVE. THERE IS NO WARRANTY FOR FITNESS FOR A PARTICULAR PURPOSE OR WARRANTY

OF MERCHANTABILITY.

EXCEPT AS OTHERWISE AGREED HEREIN McDantim, Inc. SHALL NOT BE LIABLE FOR SPECIAL OR

CONSEQUENTIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO DAMAGE TO OR LOSS OF OTHER

PROPERTY OR EQUIPMENT, LOSS OF PROFIT OR REVENUE, LOSS OF USE OF THE PRODUCT , COST

OR REPLACEMENT OF THE PRODUCT, OR CLAIMS BY CUSTOMERS FOR LOSS DUE TO SERVICE

INTERRUPTIONS. THE REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE EXCLUSIVE, AND THE

LIABILITY OF McDantim, Inc. WITH RESPECT TO ANY CONTRACT SHALL NOT, EXCEPT AS EXPRESSLY

PROVIDED HEREIN, EXCEED THE PRICE OF THE EQUIPMENT OR PART ON WHICH SUCH LIABILITY IS

BASED.

This warranty applies only to the original registered purchaser. TAMPERING, ACCIDENT, ABUSE,

NEGLECT, UNAUTHORIZED REPAIRS OR OTHER CAUSES UNRELATED TO DEFECTIVE MATERIALS OR

WORKMANSHIP WILL VOID THIS WARRANTY. McDantim, Inc. neither assumes nor authorizes

any representa ve or other person to assume for us any liability in connec on with the sales or any

shipment of our products.

PLEASE KEEP INSTRUCTIONS WITH YOUR PURCHASE RECEIPT FOR YOUR RECORDS!

Thank You for purchasing the McDantim, Inc. Trumix®Gas Blender Panel. Our goal is to

give you the most dependable, accurate and straight forward blender possible for food packaging,

welding or other related uses and products. We want you to be thoroughly happy with your new

system and would like to hear from you if for any reason you are, in any way, displeased.

The McDantim, Inc. Trumix®Gas Blender Panel is simple to install and use. It is extremely

accurate, reliable and requires li le maintenance. Properly installed, and supplied with clean, dry

gas, your Trumix®Gas Blender Panel will provide a perfect supply of mixed gas for many years.

Please take the  me to read and understand the instruc ons, the system and the cau ons.

While the system is simple there are inherent dangers in working with pressurized gases. Pressure

vessels and storage tanks, which contain both liquids and pressurized gases, can explode or

rupture and cause serious injury or death if over-pressurized or used incorrectly. Be 100% sure

you understand the implica ons of what you are doing whenever you set up, turn on or modify

this or any system. Check with your equipment supplier (in the case of storage tanks especially)

to be sure you are not exceeding any safety limits. If you have any doubt concerning the safety

of your system, get advice from or have the work done by a qualiﬁ ed specialist.

Cau on

With the Trumix®Gas Blender Panel you are dealing with pressurized gases. Serious

injury or death can result from improper installa on, use or service. All work on these

systems should be carried out by qualiﬁ ed personnel only! Before a emp ng any work

on this system be sure to read and understand these and any other instruc ons that relate

to the equipment involved in these systems! The dangers include, but are not limited to,

EXPLOSION if the maximum safe pressures for any of the individual components of the

system are exceeded or ASPHYXIATION if gases are released or leaked into a conﬁ ned

area. If you have any ques ons regarding the safety of these systems do not proceed

with the installa on or opera on un l you are 100% certain as to their safety!

Installa on Instruc ons for the

Trumix®Gas Blender Panel

Beverage: Single / Double & High Flows (w/ ILLI)

Installa on Instruc ons

Step 1: Determine the best loca on for the blender! Please consider the following:

A) Select a loca on that minimizes the chance of accidental damage to the blender.

B) Select a loca on as near as is prac cal to both the supply sources and the supplied equipment.

C) Select a loca on allowing convenient access to the shut oﬀ valve for servicing.

D) Mount panel in a weather-proof area only.

Step 2: Mount panel to wall!

Step 3: Hook up gas supply and outlet!

A) Use only the gases shown on the panel label(s).

B) Make sure you are supplying the panel with clean, dry gases that are between the minimum and

maximum pressures as indicated on the panel label.

C) Turn shut-oﬀ valve(s) on panel to the oﬀ posi on.

D) Make sure the tubing from the gas sources is compa ble with the ﬁ  ngs on the panel.

DO NOT ATTEMPT TO REMOVE INLET OR OUTLET FITTINGS.

E) Install appropriate tubing adaptors in the inlet ﬁ  ngs. Be sure to use thread sealant and back-up

wrenches. Connect gases supply lines to inlet ﬁ  ngs.

F) Conﬁ rm that your system and related equipment is safe and ready for pressurized mixed gas.

G) Connect mixed gas supply tube to mixed gas outlet ﬁ  ng.

H) Turn on the supply gases and check supply system and ﬁ  ngs for leaks.

I) Open mixed gas supply shut oﬀ valve and check system for leaks.

Opera on Guidelines and Helpful Hints

NOTES:

1) Supply the panel with clean gases.

2) Be sure no liquid can get into the blender as this will render it useless and void the warranty.

3) Some ﬁ  ngs on the panel do not have standard US threads, and should not be removed with out

checking with McDantim, Inc.!

4) NEVER EXCEED THE RECOMMENDED PRESSURES FOR ANY PART OF YOUR SYSTEM!

Trouble-shoo ng: No Outlet Gas

1) Close shut-oﬀ valve. Check pressure on pressure gauge. If pressure is low or zero, check:

a) Both supply gases. (One or both could be empty, turned oﬀ or out of adjustment.)

b) For blockage of either supply line or for a closed valve within the supply system. (The blender shuts

oﬀ if either supply gas is unavailable.)

If pressure is good:

d) Open shut-oﬀ valve completely.

2) If you con nue to have no gas, close shut-oﬀ valve, remove tubing from outlet, open shut-oﬀ valve and

check for gas ﬂ ow.

3) If you s ll have no supply gas, call McDantim, Inc. or your gas supplier or service person. There are

no user-serviceable parts within the panel. Anything done to the internal parts will aﬀ ect the blend

and void the warranty.

If you encounter other ques ons or problems call:

McDantim, Inc. (888) 735-5607 or (406) 442-5153

Warning! With this or any compressed gas system,

there are certain dangers. If you do not have the

experience to understand these dangers, use a

professional installer.

Trumix®Gas Blender Panel

Installaon Instrucons

Use primary regulators on your

gas source suitable for your

panel specicaons.

Example: If your inlet pressure

label states “Min. inlet pressure

55 psi” then you must provide at

least 55 psi to the Blender Panel.

1. Use thread sealant.

2. Do not remove ngs.

3. Use back-up wrenches.

Plug & Play In Line Leak Indicator Installaon Instrucons (ILLI)

(may not be included - can be purchased using part # MV098)

1. Remove vinyl caps from stand pipes and slide into female compression ngs that are installed on the McDanm Trumix® panel.

2. Tighten the compression ngs nger ght to hold the ILLI in place and screw mounng bracket securely to the wall.

3. Re-check that ngs are nger ght and then turn both compression ng hex nuts another three quarters of a turn (14 mm size).

4. Once the ILLI is installed, hook up the inlet gases to the installed hose barbs and bring the panel up to pressure

with the outlet ball valves closed.

Note: At this point you should not see any leaks by referencing the indicator,

if you do see a leak you may need to ghten the compression ngs further.

N2CO2

Use reinforced tubing suitable for 150 psi.

Mixed Gas Out

Plug & Play

ILLI

NOTE

These instrucons apply to the Trumix®Single and

Trumix®Double as well as their High Flow models.

The picture to the right is of a Trumix®Double . The

Trumix®Single will have only one outlet assembly,

which is on the right-hand side.

TM-2-HPR+ILLI

Installa on Instruc ons

Step 1: Determine the best loca on for the blender! Please consider the following:

A) Select a loca on that minimizes the chance of accidental damage to the blender.

B) Select a loca on as near as is prac cal to both the supply sources and the supplied equipment.

C) Select a loca on allowing convenient access to the shut oﬀ valve for servicing.

D) Mount panel in a weather-proof area only.

Step 2: Mount panel to wall!

Step 3: Hook up gas supply and outlet!

A) Use only the gases shown on the panel label(s).

B) Make sure you are supplying the panel with clean, dry gases that are between the minimum and

maximum pressures as indicated on the panel label.

C) Turn shut-oﬀ valve(s) on panel to the oﬀ posi on.

D) Make sure the tubing from the gas sources is compa ble with the ﬁ  ngs on the panel.

DO NOT ATTEMPT TO REMOVE INLET OR OUTLET FITTINGS.

E) Install appropriate tubing adaptors in the inlet ﬁ  ngs. Be sure to use thread sealant and back-up

wrenches. Connect gases supply lines to inlet ﬁ  ngs.

F) Conﬁ rm that your system and related equipment is safe and ready for pressurized mixed gas.

G) Connect mixed gas supply tube to mixed gas outlet ﬁ  ng.

H) Turn on the supply gases and check supply system and ﬁ  ngs for leaks.

I) Open mixed gas supply shut oﬀ valve and check system for leaks.

Opera on Guidelines and Helpful Hints

NOTES:

1) Supply the panel with clean gases.

2) Be sure no liquid can get into the blender as this will render it useless and void the warranty.

3) Some ﬁ  ngs on the panel do not have standard US threads, and should not be removed with out

checking with McDantim, Inc.!

4) NEVER EXCEED THE RECOMMENDED PRESSURES FOR ANY PART OF YOUR SYSTEM!

Trouble-shoo ng: No Outlet Gas

1) Close shut-oﬀ valve. Check pressure on pressure gauge. If pressure is low or zero, check:

a) Both supply gases. (One or both could be empty, turned oﬀ or out of adjustment.)

b) For blockage of either supply line or for a closed valve within the supply system. (The blender shuts

oﬀ if either supply gas is unavailable.)

If pressure is good:

d) Open shut-oﬀ valve completely.

2) If you con nue to have no gas, close shut-oﬀ valve, remove tubing from outlet, open shut-oﬀ valve and

check for gas ﬂ ow.

3) If you s ll have no supply gas, call McDantim, Inc. or your gas supplier or service person. There are

no user-serviceable parts within the panel. Anything done to the internal parts will aﬀ ect the blend

and void the warranty.

If you encounter other ques ons or problems call:

McDantim, Inc. (888) 735-5607 or (406) 442-5153

Warning! With this or any compressed gas system,

there are certain dangers. If you do not have the

experience to understand these dangers, use a

professional installer.

Trumix®Gas Blender Panel

Installaon Instrucons

Use primary regulators on your

gas source suitable for your

panel specicaons.

Example: If your inlet pressure

label states “Min. inlet pressure

55 psi” then you must provide at

least 55 psi to the Blender Panel.

1. Use thread sealant.

2. Do not remove ngs.

3. Use back-up wrenches.

Plug & Play In Line Leak Indicator Installaon Instrucons (ILLI)

(may not be included - can be purchased using part # MV098)

1. Remove vinyl caps from stand pipes and slide into female compression ngs that are installed on the McDanm Trumix® panel.

2. Tighten the compression ngs nger ght to hold the ILLI in place and screw mounng bracket securely to the wall.

3. Re-check that ngs are nger ght and then turn both compression ng hex nuts another three quarters of a turn (14 mm size).

4. Once the ILLI is installed, hook up the inlet gases to the installed hose barbs and bring the panel up to pressure

with the outlet ball valves closed.

Note: At this point you should not see any leaks by referencing the indicator,

if you do see a leak you may need to ghten the compression ngs further.

N2CO2

Use reinforced tubing suitable for 150 psi.

Mixed Gas Out

Plug & Play

ILLI

NOTE

These instrucons apply to the Trumix®Single and

Trumix®Double as well as their High Flow models.

The picture to the right is of a Trumix®Double . The

Trumix®Single will have only one outlet assembly,

which is on the right-hand side.

TM-2-HPR+ILLI