MDS Orbit MCR-4G Bedienungsanleitung

Installation and Operation Guide

Technical Manual

MDS 05-6628A01, Rev. B

Preliminary

AUGUST 2013

MDSTM Orbit MCR-4G

Managed Connected Router 4G and WiFi

Quick-Start instructions for this product are contained in publication 05-6702A01.

Visit our website for downloadable copies of all documentation at www.gemds.com.

MDS 05-6628A01, Rev. B MDS Orbit MCR-4G Technical Manual i

TABLE OF CONTENTS

1.0 INTRODUCTION...........................................................................................................................1

1.1 About This Manual .................................................................................................................................. 1

Software Command Notations.................................................................................................................. 1

Authorized Features Icon.......................................................................................................................... 2

2.0 PRODUCT DESCRIPTION............................................................................................................3

2.1 Key Features ............................................................................................................................................ 3

2.2 Interface Types ........................................................................................................................................ 3

2.3 Typical Application ................................................................................................................................. 3

2.4 Connectors and Indicators ....................................................................................................................... 4

Grounding Considerations ........................................................................................................................ 9

Mounting Options..................................................................................................................................... 9

Optional DIN Rail Mounting.................................................................................................................... 9

Antenna Planning & Installation ........................................................................................................... 10

Accessories and Spares........................................................................................................................... 12

3.0 Device Management......................................................................................................................13

3.1 Connecting a PC .................................................................................................................................... 13

Differences Between Serial & SSH ........................................................................................................ 13

Establishing Communication—Serial Interface...................................................................................... 13

Setting Basic Parameters—First Steps.................................................................................................... 14

One-Time “Recovery” Passwords........................................................................................................... 14

3.2 Pre-Configured Settings ........................................................................................................................ 16

3.3 YANG Interface ..................................................................................................................................... 16

CLI Login Prompt................................................................................................................................... 17

3.4 Operational Topic Areas......................................................................................................................... 23

Serial Console...................................................................................................................... 24

Network ................................................................................................................................ 25

LAN ...................................................................................................................................... 26

VLAN Operation................................................................................................................... 28

Cell ....................................................................................................................................... 29

WiFi ...................................................................................................................................... 32

Bridging................................................................................................................................ 37

Routing ................................................................................................................................. 40

Firewall and NAT.................................................................................................................. 41

VPN...................................................................................................................................... 50

DNS ...................................................................................................................................... 57

DHCP Service...................................................................................................................... 58

Iperf Service......................................................................................................................... 61

Date, time and NTP.............................................................................................................. 62

Geographical-location .......................................................................................................... 63

User Management and Access Controls.............................................................................. 64

Login-Lockout....................................................................................................................... 66

RADIUS................................................................................................................................ 67

ii MDS Orbit MCR-4G Technical Manual MDS 05-6628A01, Rev. B

File Servers.......................................................................................................................... 68

Certificate Management ....................................................................................................... 69

Event Logging ...................................................................................................................... 77

Firmware Management ........................................................................................................ 78

Support Bundle .................................................................................................................... 80

4.0 Technical Reference........................................................................................................81

4.1 Troubleshooting ..................................................................................................................................... 81

LED Status Indicators............................................................................................................................. 81

4.2 Specifications ........................................................................................................................................ 82

4.3 Agency/Regulatory Approvals .............................................................................................................. 82

4.4 Glossary of Terms & Abbreviations ...................................................................................................... 82

5.0 APPENDIX A – Data Configuration Tree ...................................................................................85

6.0 APPENDIX B – Command Line Interface (CLI) Features.........................................................101

7.0 APPENDIX C – Integrity Measurement Authority (IMA) .........................................................115

8.0 APPENDIX D-G .........................................................................................................................125

This manual and all software described herein is protected by Copyright: 2013 GE MDS, LLC. All

rights reserved. GE MDS, LLC reserves its right to correct any errors and omissions in this publi-

cation.

RF Safety Notice (English and French)

Concentrated energy from a directional antenna may pose a health hazard to

humans. Do not allow people to come closer to the antenna than the distances

listed in the table below when the transmitter is operating. More information on

RF exposure can be found online at the following website:

www.fcc.gov/oet/info/documents/bulletins.

Concentré d'énergie à partir d'une antenne directionnelle peut poser un risque

pour la santé humaine. Ne pas permettre aux gens de se rapprocher de l'antenne

que les distances indiquées dans le tableau ci-dessous lorsque l'émetteur est en

marche. Plus d'informations sur l'exposition aux RF peut être trouvé en ligne à

l'adresse suivante: www.fcc.gov / oet / info / documents et bulletins.

RF Exposure

l'exposition aux RF

MDS 05-6628A01, Rev. B MDS Orbit MCR-4G Technical Manual iii

Antennas must not be co-located. All transmission antennas must be at least 20 cm apart to comply

with FCC co-location rules.

FCC Part 15 Notice

Operation is subject to the following two conditions: (1) this device may not cause harmful inter-

ference, and (2) this device must accept any interference received, including interference that may

cause undesired operation. Any unauthorized modification or changes to this device without the

express approval of the manufacturer may void the user’s authority to operate this device. Further-

more, this device is intended to be used only when installed in accordance with the instructions out-

lined in this manual. Failure to comply with these instructions may void the user’s authority to

operate this device.

Industry Canada Notice

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Operational Safety Notices

The MDS Orbit MCR-4G may not be used in an environment where radio frequency equipment is

prohibited or restricted in its use. This typically includes aircrafts, airports, hospitals, and other sen-

sitive electronic areas.

Do not operate RF devices in an environment that may be susceptible to radio interference

resulting in danger, specifically:

• Areas where prohibited by law

Follow any special rules and regulations and obey all signs and notices. Do not use the MCR-4G

when you suspect that it may cause interference or danger.

• Near Medical and life support equipment

Do not use the MCR-4G in any area where medical equipment, or life support equipment may be

located, or near any equipment that may be susceptible to any form of radio interference.

Orbit Device vs. Minimum RF Safety Distance

Radio Module Type Minimum Safety Distance

from Antenna

MCR-4G 20 cm

MCR-900 23 cm

Other models Consult factory prior to operation.

iv MDS Orbit MCR-4G Technical Manual MDS 05-6628A01, Rev. B

Cellular Operational Bands

The following table shows the bands in which the cellular module operates for each wireless tech-

nology.

FCC IDs of Installed Transmitters

As of the date of printing, the following FCC identifiers are assigned to the modules listed below.

For the latest, official listings of all agency approval information, please contact your factory rep-

resentative.

CELL Modem FCC ID: PKRNVWE362, IC ID: 3229B:E362

WIFI Module FCC ID: M4Y-ZCN722MV1, IC ID 3195A-ZCN722MV1

CE Mark and RTTE Notice

This product, using the "WIFI internal radio module" only, is CE marked and compliant with the

RTTE directive. Other configurations will be added for EU use in future releases.

Servicing Precautions

No user-serviceable parts are contained inside this equipment. Opening of the unit by unauthorized

personnel voids the warranty. All servicing must be performed by an authorized repair facility.

When servicing energized equipment, be sure to wear appropriate Personal Protective Equipment

(PPE). During internal service, situations could arise where objects accidentally contact or short

circuit components and the appropriate PPE would alleviate or decrease the severity of potential

injury. When servicing equipment, all workplace regulations and other applicable standards for

live electrical work should be followed to ensure personal safety.

MDS 05-6628A01, Rev. B MDS Orbit MCR-4G Technical Manual v

Manual Revision and Accuracy

This manual was prepared to cover a specific version of firmware code. Accordingly, some screens

and features may differ from the actual unit you are working with. While every reasonable effort

has been made to ensure the accuracy of this publication, product improvements may also result in

minor differences between the manual and the product shipped to you. If you have additional ques-

tions or need an exact specification for a product, please contact GE MDS using the information at

the back of this guide. In addition, manual updates can be found on our web site at

www.gemds.com

Environmental Information

The manufacture of this equipment has required the extraction and use of natural resources.

Improper disposal may contaminate the environment and present a health risk due to hazardous

substancescontained within. To avoid disseminationofthesesubstances into our environment, and

to limit the demand on natural resources, we encourage you to use the appropriate recycling sys-

temsfordisposal.Thesesystemswillreuseorrecyclemostofthe materials found in this equipment

in a sound way. Please contact GE MDS or your supplier for more information on the proper dis-

posal of this equipment.

Battery Disposal—This product may contain a battery. Batteries must be disposed of properly, and

may not be disposed of as unsorted municipal waste in the European Union. See the product doc-

umentation for specific battery information. Batteries are marked with a symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling return

the battery to your supplier or to a designated collection point. For more information see:

www.weeerohsinfo.com.

Product Test Data Sheets

Test Data Sheets showing the original factory test results for this unit are available upon request

from the GE MDS Quality Leader. Contact the factory using the information at the back of this

manual. Serial numbers must be provided for each product where a Test Data Sheet is required.

CSA/us Notice

This product is approved for use in Class 1, Division 2, Groups A, B, C & D Hazardous Locations.

Such locations are defined in Article 500 of the National Fire Protection Association (NFPA) pub-

lication NFPA 70, otherwise known as the National Electrical Code. The transceiver has been rec-

ognized for use in these hazardous locations by the Canadian Standards Association (CSA) which

also issues the US mark of approval (CSA/US). The CSA Certification is in accordance with CSA

STD C22.2 No. 213-M1987.

CSA Conditions of Approval: The transceiver is not acceptable as a stand-alone unit for use in the

hazardous locations described above. It must either be mounted within another piece of equipment

which is certified for hazardous locations, or installed within guidelines, or conditions of approval,

as set forth by the approving agencies. These conditions of approval are as follows: The transceiver

must be mounted within a separate enclosure which is suitable for the intended application.The

antenna feedline, DC power cable and interface cable must be routed through conduit in accor-

dance with the National Electrical Code. Installation, operation and maintenance of the transceiver

vi MDS Orbit MCR-4G Technical Manual MDS 05-6628A01, Rev. B

should be in accordance with the transceiver's installation manual, and the National Electrical

Code. Tampering or replacement with non-factory components may adversely affect the safe

use of the transceiver in hazardous locations, and may void the approval. A power connector

with screw-type retaining screws as supplied by GE MDS must be used.

Do not disconnect equipment unless power has been switched off or the area is known to

be non-hazardous. Refer to Articles 500 through 502 of the National Electrical Code

(NFPA 70) for further information on hazardous locations and approved Division 2 wiring

methods.

EXPLOSION

HAZARD!

MDS 05-6628A01, Rev. B MDS Orbit MCR-4G Technical Manual 1

1.0 INTRODUCTION

This manual describes the MDS Orbit MCR-4G Managed Connected Router (Figure 1). The unit is a highly

secure, industrial grade, wireless communication product for broad based applications including control

center monitoring, well site pad operations, and video surveillance. It serves the need for localized WiFi

communications with a cellular back-up or backhaul option, while providing the extended temperature

range and industrial-grade packaging inherent to GE MDS products. These features allow the best use of

communication options at each installation site.

Figure 1. MCR-4G Unit

(Standard 2E1S configuration shown)

With a common hardware architecture and user interface, the MCR offers flexibility in network design and

application, with simplified training, maintenance, and deployment costs. GE MDS provides an array of

communication products with multiple interface options and a variety of enclosures to give customers the

choice and flexibility to design their communications network to meet geographic and industry specific

challenges. Information on other GE MDS products can be found by visiting our website at

www.gemds.com.

1.1 About This Manual

This manual is intended for systems engineers, network administrators, and others responsible for planning,

commissioning, using, and troubleshooting the wireless system. Installation steps are not included in this

publication. For installation instructions, refer to the MCR-4G Setup Guide, part no. 05-6702A01. Elec-

tronic copies of all user documentation are available free of charge at www.gemds.com.

1.1.1 Software Command Notations

The product is designed for software control via a connected PC. As such, there are no external controls or

adjustments present. To show the names of software commands, keyboard entries, or other information dis-

played on a PC screen, a bolded font is used throughout the manual. In the case of tabular data displayed on

a PC screen, a variation on this font is used to maintain proper layout. (See examples that follow.)

The MCR-4G Setup Guide, Part no. 05-6702A01,

contains installation instructions, as well as basic

startup information for this product.

All GE MDS user manuals and updates are available

online at www.gemds.com.

2 MDS Orbit MCR-4G Technical Manual MDS 05-6628A01, Rev. B

Bolded font example (used for software commands and keyboard entries)

Bolded font example (used for tabular screen data)

In the Device Management section, there are a number of command strings where information is presented

by the unit, and a reply is required from the user. In such cases, information from the unit is shown in a

non-bolded font, and the user response is shown in bold. For example:

(none) login: admin

Further, in some cases, command lines will be shown with non-bolded, italicized text contained within the

string. Such text indicates the need for user-supplied parameters, such as the name of an item. For example:

setinterfacesinterfacemyBridgevirtual‐typebridge

In the above example, you would enter the specific name of your bridge to complete the command line entry.

NOTE: The software commands and responses shown in this manual were obtained from a unit operating

in a lab environment. The information displayed may differ from field service conditions.

1.1.2 Authorized Features Icon

Some product features are dependent on purchased options and applicable regulatory constraints. A “key”

icon appears near the heading of any such features.

Andere Handbücher für Orbit MCR-4G

Inhaltsverzeichnis

Andere MDS Netzwerk-Router Handbücher

MDS

MDS Orbit MCR-4G Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise