Mecam DM07 Bedienungsanleitung
1
2
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is
subjected to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation. SAR test distance is 0mm.
This equipment has been tested and found to comply with
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. The equipment complies with FCC RF exposure limits set
forth for an uncontrolled environment.
These limits are designed to provide reasonable protection
against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause interference to radio or television
equipment reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Move the equipment away from the receiver.
-Plug the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/television
technician for additional suggestions.
You are cautioned that any change or modifications to the
equipment not expressly approved by the party responsible for
compliance could void your authority to operate such
equipment.
3
Safety Instructions
•Do not drop, puncture or disassemble the device; otherwise
the warranty will be voided.
•Avoid all contact with water. Dry your hands before using
the device.
•Use the device with care. Avoid pressing hard on the device
body.
•For your own safety, avoid using the device when there is a
storm or lightning.
•Use only the accessories supplied by the manufacturer.
•Keep the device out of the reach of infants.
•Do not leave the device on the dashboard where it is subject
to direct sunlight.
•The battery is integrated with the device. Do not dissemble
and modify. The battery should be replaced by an
authorized service center only.
4
Introduction
MeCam is hands-free wearable camera that you can pin or clip
it to your shirt, wear it as a necklace, or mount it to the car
windshield to record high quality videos and pictures.
Package Content
The following items come with your package.
Camera USB Cable Car Adapter (Optional)
Strap Clip Pin Clip
Stand Suction Cup Bracket
(Optional)
5
Product Overview
Function button
Power button
Wi-Fi LED
Function LED
Power LED
Micro SD card slot
Micro USB port
HDMI port
Microphone
6
Buttons and LED Indicators
Button Functions
Status Action
Power on Press and hold the Power button for 2 seconds.
Power off Press and hold the Power button for 3 seconds.
Turn off Wi-Fi Press and hold the Power button for 6 seconds.
Start recording Press and hold the Function button for 3 seconds.
Stop recording While recording, press and hold the Function
button for 3 seconds.
Take photo Press the Function button.
Reset to default Press and hold the Function button for 10
seconds.
Reboot Press and hold the Power button for 10 seconds.
LED Indicators
Status Power LED Wi-Fi LED Function LED
Power on Light Green Light Green Off
Start recording Light Green Light Green Blink Green
Wi-Fi off Light Green Off Off
Power off Off Off Off
Battery is charging Off Off Light Red
Charging complete Off Off Off
Low battery Blink Red Off Off
7
Getting Started
Inserting the Memory Card
Insert the memory card with the gold
contacts facing to the front of the device.
Push the memory card until it clicks into
place.
About SD Card
•Please use SD card with the size/memory at least 8GB, Class
10 (up to 64GB).
•Be sure to format SD card using the device before the initial
usage.
•Do not remove the memory card while recording. This may
damage the memory card.
Charging the Battery
1. Connect one end of the USB cable to the micro USB port of
the device.
2. Connect the other
end of the USB cable
to the computer.
8
Note
•As an alternative, you can also charge the device using an AC
adapter.
Powering the Device On/Off
•To turn on the power, press and hold
the Power button for 2 seconds.
•To turn off the power, press and hold
the Power button for 3 seconds.
9
Connecting to Your Smartphone
List of Supported Smartphone
•iOS device: iOS 6.1 or above
•Android device: Android 4.0 or above
Install MeCam HD APP
1. Make sure your smartphone is connected to the Internet.
2. Launch App Store (iOS)or Google Play/Play Store (Android)
application.
3. On the search bar, enter the keyword “MeCamHD” to search
for APP.
4. Download and install MeCam HD. After the installation is
complete, the MeCam icon ( ) is displayed on the
application screen.
Note
•When you use a code reader application to scan the
respective QR code below, your smartphone will show a
direct link to download MeCam HD.
(iOS) (Android)
•The application UI varies depending on the device operating
system and design.
10
Connect via Wi-Fi
1. On your smartphone, launch Settings application.
2. In WIRELESS & NETWORKS, tap
Wi-Fi and set it to ON.
The available networks are listed.
3. Tap MeCamHD to connect to the
camera.
4. Enter the password and tap Join
(iOS) or Connect (Android).
Note
•The default password is “Enjoylife”.
•You can change the SSID and password in Setup mode.
Inhaltsverzeichnis
