Megapixall MPIX-IP1MPIR30 Bedienungsanleitung

MPIX-IP1MPIR30 Quick Start Guide

Version 1.0.1

Welcome

Thank you for purchasing our network camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC in the IEC60950-1. This series product supports PoE too. Please note:

Do not connect these two power supplying sources to the device at the same time; it may result

in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,

inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

Thunder-proof device is recommended to be adopted to better prevent thunder.

The grounding studs of the product are recommended to be grounded to further enhance the reliability

of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

Network Camera 1

Quick Start Guide 1

Installation Accessories Bag 1

CD 1

iii

Table of Contents

1Structure ......................................................................................................................................1

1.1 Device Components.....................................................................................................1

1.2 Dimensions....................................................................................................................2

1.3 Bidirectional talk ...........................................................................................................3

1.3.1 Device-end to PC-end ..........................................................................................3

1.3.2 PC-end to the Device-end....................................................................................3

1.4 Alarm Setup...................................................................................................................4

1.4.1 Alarm Input and Output Connection...................................................................4

2Device Installation ......................................................................................................................6

3Quick Configuration Tool...........................................................................................................8

3.1 Overview........................................................................................................................8

3.2 Operation .......................................................................................................................8

4Web Operation..........................................................................................................................11

4.1 Network Connection...................................................................................................11

4.2 Login and Logout........................................................................................................11

5FAQ ............................................................................................................................................14

Appendix Toxic or Hazardous Materials or Elements ...............................................................16

1Structure

1.1 Device Components

You can refer to the following figure for component information. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

SN Port Name Indicator Connector Note

1 Power indicator

light POWER /

zWhen system boots up–Green

light becomes on.

zWhen system is upgrading –

Green light flashes. Interval is

0.5s.

zWhen system is alarming–

Green light flashes. Interval is

0.2s.

2 Network

indicator light NET /

zWire network connection-Red

light is on.

zWireless network connection-

Green light is on.

3 Speaker / /

Output audio signal.

(This function is optional. For some

series product only.)

4 White light / /

Can activate motion detect, PIR

human body movement detect,

external alarm.

SN Port Name Indicator Connector Note

5 PIR sensor PIR /

Passive IR motion detect port. It

can detect the IR object movement

(such as human body or other

heating object).

6 Microphone / /

Directly receive audio signal.

(This function is optional. For some

series product only.).

7 Micro SD card Micro SD Micro SD

card slot

SD card storage.

(This function is optional. For some

series product only.).

8 Reset button Reset /

Restore factory default setup.

When system is running normally,

press the RESET button for at least

5 seconds, system can restore

factory default setup.

9 WPS button WPS Fast wireless

connection

Press the WPS button of the router

and the device respectively for at

least 2 seconds. Usually the device

can connect to the router within 1

minute.

Please note it is for wireless

series product only and it is for

the wireless router of the WPS

function.

10 Alarm pin / I/O port

Alarm signal input/output

(This function is optional. For some

series product only.).

11 Power port DC12V / Input DC 12V power.

12 Network port LAN Ethernet port

zConnect to standard Ethernet

cable.

zSupport PoE function.

1.2 Dimensions

Please refer to the following figure for dimension information. The unit is mm. See Figure 1-2.

Figure 1-2

1.3 Bidirectional talk

1.3.1 Device-end to PC-end

Device Connection

Please connect the speaker or the MIC to the audio input port in the device rear panel. Then connect

the earphone to the audio output port in the PC.

You can see the button becomes orange after you enabled the audio talk function.

Click Audio button again to stop the bidirectional talk function.

Listening Operation

Speak or play music at the PC-end, you can use the earphone or the sound box of the PC-end to

listen the audio information from the device-end.

1.3.2 PC-end to the Device-end

Device Connection

Connect the speaker or the MIC to the audio input port in the PC and then connect the earphone to the

audio output port of the device.

You can see the button becomes orange after you enabled the audio talk function.

Click Audio button again to stop the bidirectional talk function.

Listening Operation

Speak or play music at the PC-end, you can use the built-in speaker of the device-end to listen.

Note

Please go to the Master Volume interface of the PC to set first if you want to use the dual-way

bidirectional talk. Please select Front Mic mode in the record control interface. (You can select

microphone enhanced in Advanced interface if the audio is too low.)

1.4 Alarm Setup

The alarm setup interface is shown as below. See Figure 1-3.

Figure 1-3

1.4.1 Alarm Input and Output Connection

Please refer to the following figure for alarm input information. See Figure 1-4.

Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of

the alarm input port. When the input signal is connected to the 3.3V or is idle, the device collects the

logic “1”. When the input signal is grounded, the device collects the logic “0”.

Figure 1-4

Please refer to the following figure for alarm output information. See Figure 1-5.

Port NO and Port C composes an on-off button to provide the alarm output.

This button is normal open. The button becomes off when there is an alarm output.

Figure 1-5

2Device Installation

This series camera support two installation modes: wall mount and pendant mount. See Figure 2-1

and Figure 2-2.

Important

Please make sure the installation surface can min support the 3X weight of the camera and the

bracket.

Step 1

Paste the installation positioning map on the installation surface such as wall, ceiling or the wood.

Step 2

Dig holes in the installation surface according to the installation positioning map.

Step 3

Insert the expansion bolts from the accessories bag to the holes you just dug. If it is the wood surface

you can skip to the next step.

Step 4

Use the screws from the accessories bag to secure the device firmly.

Step 5

Connect the cable and then boot up the device.

Step 6

Loosen the adjust knob for a little bit, adjust the camera to proper surveillance position according to

your actual requirements.

Step 7

Secure the knob of the bracket to fix the camera.

Figure 2-1

Inhaltsverzeichnis

Andere megapixall Sicherheitskamera Handbücher

megapixall

megapixall MPIX-IPB1MPIR50 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

megapixall MPIX-IP1MPIR30 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken