Megger S1-5010 Bedienungsanleitung

S1-5010

Diagnostic Insulation Tester

User Guide

GSAFETY WARNINGS

•Safety Warnings and Testing Precautions must be read and understood before the

instrument is used. They must be observed during use

•The circuit under test must be switched off, de-energised and isolated before test

connections are made.

•The test terminal panel and side recess panel must be kept in a dry, clean condition.

•Circuits must be discharged before disconnecting the test leads - Capacitive loads

can be lethal. See ‘Testing Precautions’.

•Circuit connections must not be touched during a test.

•In certain circumstances, break-down of the circuit under test may cause the

instrument to terminate the test in an uncontrolled manner, possibly causing a loss of

display and warning indications while the circuit remains energised. In this event, it is

important that the circuit is discharged and the instrument is turned off, before

touching any connections.

•Replacement fuses must be of the correct type and rating.

•The instrument should not be used if any part of it is damaged.

•Refer to ‘Testing Precautions’for further explanations and precautions.

Symbols used on the instrument

GCaution: Refer to accompanying notes.

FRisk of electric shock.

cEquipment complies with relevant EU Directives

tEquipment protected throughout by Double Insulation (Class II).

NOTE

THE INSTRUMENT MUST ONLY BE USED BY SUITABLY TRAINED AND COMPETENT PERSONS.

Contents

Safety Warnings 2

General Description 4

Features and Controls 5

Battery or Mains Operation 6

Mains supply re-charging 6

12 V supply re-charging 6

Battery Charging Notes 6

Setting up procedures 7

Setup Language 7

Setup IR, SV and DD Tests 7

Setup PI Tests 7

Disable a Test Mode 8

Enable a Test Mode 8

Delete Stored Test Results 9

Set / Reset Date and Time 9

Set / Reset Printer Baud rate 10

Set / Reset PC Baud rate 10

Setup / Reset ‘Power On’ code 10

Setup / Reset ‘Setup’ code 11

Set / Reset Date format 11

Set / Reset Current limit 11

Set / Reset Data Output Rate 11

Set / Reset Locking test button 12

Operation 13

Testing Precautions 13

Performing tests - General 14

Using the Filter 15

Fault Conditioning (Burn) 16

Remote Operation 16

Test Mode Summary 17

Insulation Resistance Testing 17

Polarization Index Testing 17

Dielectric discharge Testing 18

Step Voltage Testing 18

Fault Conditioning (Burn) 19

Data Retrieve 20

Display stored Test results 20

Download stored Test results to a printer 20

Downloading Test results to a PC 20

Application Notes 21

Preventive Maintenance 21

Insulation testing concepts 22

Test Techniques 23

Using the Guard terminal 23

Measurements above 100 GΩ23

Circuit block diagram 24

Calibration Check 24

Appendix 1 25

Specification 26

Accessories 27

Repair and Warranty 28

The S1-5010 is an advanced insulation tester for all types of electrical equipment offering

measurement capability up to several T. The instrument performs automatic tests, enabling

consistent operation without operator input, stores results and can be operated from a PC. Flexible

power supply options and robust, portable construction allow the instrument to be used in a wide

variety of applications. It is particularly suitable for analyzing the insulation of large machines, HV

generators and cables. When turned On, voltage in excess of 50 volts across the + and - terminals

will be indicated on the display, together with the flashing HV symbols.

Switchable filtering allows stable readings to made when in the presence of high levels of 50 Hz or

60 Hz interference.

PPoo

oollllaa

aarr

rriiiizz

zzaa

aatt

ttiiiioo

oonn

IIIInn

nndd

ddee

eexx

xx and DD

DDiiiiee

eellllee

eecc

cctt

ttrr

rriiiicc

DDiiiiss

sscc

cchh

hhaa

aarr

rrgg

ggee

ee tests are performed automatically, and test duration

and voltages can be adjusted according to user preference for these tests. A SS

SStt

ttee

eepp

VVoo

oolllltt

ttaa

aagg

ggee

ee test can

also be performed automatically, with a voltage of 2500 V or 5000 V and a fixed test duration of 5

minutes. It is also possible to restrict operation to user defined voltages, to disable the graph plotting

or to disable certain types of tests. This is all done using the ‘SS

SSee

eett

ttuu

uupp

pp’ screen. The settings can be

security code protected. It is also possible to set a general security code to prevent unauthorized use

of the instrument.

The S1-5010 can be powered from the main supply, or by the its own internal rechargeable battery

which provides for at least 8 hours of continuous testing. The battery symbol ,in the bottom

left of the display indicates battery capacity. Connecting power to the supply connector, or to the 12

volt connector in the side recess panel will automatically charge the battery whether the instrument

is switched ‘OO

OOnn

nn’ or ‘OO

OOff

ffff

ff’. A high level of internal isolation allows the S1-5010 to be used while the

battery is being recharged. An internal battery management system switches the instrument off after

ten minutes of inactivity. Test results and settings will not be lost when the instrument is switched off.

Test results are stored internally but the RS232 connection allows an external computer to receive

results in real time or to receive results previously stored.

Safe testing is achieved with a double insulated plastic case, double insulated test lead connectors,

a one second delayed start test button, high voltage warning symbols , flash on the display,

and the test terminal HV warning light flashes. A socket in the side recess panel provides a 5 volt

logic signal to drive an external warning light. Capacitive loads are automatically discharged at the

end of a test.

Beneath the display, four tactile keys normally control:-

- Electrical ‘noise’ Filter

- Contrast

- Back-light.

General Description

RS232 connection

Download ‘Real time’ or

‘Batch’ results to PC.

Remote operation.

12 V d.c. connection

Plug in supply of 10 - 15 V

to charge the battery

Battery Charge Indicator

Mains connection

Plug in supply of 95 - 265 V a.c.

to charge the battery.

Fuse

200 mA - 250 V

HV ‘On’ indicator connection

5 V logic signa output.

(To connect an external HV

indicator)

Side recess Panel

Features and Controls

Power On / Off Switch

Press to turn On / Off.

Left Hand Cursor keys

Press to:-

i) Select and highlight the

required mode.

ii) Select test Results /

& Bargraph / Graph

in Enhanced mode.

(when test has run ≥1 minute)

HV Warning

Flashes when a test is in

progress or a hazardous

voltage is present. Right Hand Cursor

keys

Press to select and

highlight the required

voltage before

commencing test.

VARI position

Gives the option to:-

i) Select a non standard

voltage between 25 V

and 5000 V before

commencing test.

ii) Continuously vary the

voltage in 25 V steps

during a test.

Filter key

Press to:-

i) Sequentially select filter times.

(See ‘Using the Filter’)

ii) Initiate the ‘On screen’ display

above the key.

Contrast keys

Press to:-

i) Adjust the screen contrast.

ii) Initiate the ‘On screen’display

above the key

Backlight key

Press to:-

i) Switch backlight On or Off.

ii) Initiate the ‘On screen’

display above the key.

Mode setting

Date and time

Voltage setting

Battery Capacity Indicator

Test duration

Test Button

Negative Terminal Positive Terminal

Guard Terminal

Toinsert and lock in shrouded test plugs

Push in

To release shrouded test plugs

turn a quarter turn and pull out

The S1-5010 can be powered by:

• Internal rechargeable battery which provides at least 8 hours of testing.

• Mains input of 95 volts to 280 volts 50/60 Hz.

• 12 - 15 Volts d.c or a.c.

General

The S1-5010 is fitted with a 12 volt, 7 Amp-hour sealed lead-acid battery. The maintenance free

battery will last for at least 5 years if kept charged and not subjected to prolonged high temperatures.

(Occasional exposure to +50° C will do little harm but a continuous temperature >40° may cause

irreparable damage). It is advisable to fully charge the battery before the instrument is put into service

for the first time. Charging is carried out by external a.c. mains supply, or by 12 V d.c. or a.c. supply.

To fully recharge the battery after 8 hours of use takes about 16 hours. The battery capacity display

symbol indicates the state of charge.

Mains supply re-charging

The application of a mains supply of 95 - 265 V a.c., 50 - 60 Hz powers the instrument, and charges

the battery. The S1-5010 will operate on a supply as low as 90 volts, but this will not fully charge the

battery. Charging is automatic as soon as the mains supply is connected to the IEC 320 connector in

the side recess panel. Confirm that the red indicator lamp is illuminated.

12 V supply re-charging

The application of an external 12 - 15 volt d.c or a.c. supply powers the instrument and charges the

battery at the same rate of charge as the mains input. It is possible to connect both mains and a 12

volt input simultaneously, but this will not charge the battery any faster. The socket accepts 12 -15 volt

d.c. (any polarity connection) or 12 - 15 volt a.c. A charging lead fitted with an automotive cigar lighter

plug for charging the battery from a vehicle is available (See ‘Accessories’). Charging is automatic

as soon as the 12 V supply is connected to the 12 V DIN socket. Confirm that the red indicator lamp

is illuminated.

12 V DIN socket

Caution:- Applying more than 15 V to this socket may overcharge the battery.

Battery Charging Notes

• Do not leave battery in a totally discharged state. Frequent charging to keep the battery ‘topped

up’ will maximise battery life.

• When charging the battery indoors, the area should be well ventilated.

• The battery should only be charged at temperatures in the range 0 °C to 40 °C.

• No harm will occur to the battery is kept on charge indefinitely.

• If the instrument is idle for long periods, recharge the battery for at least 24 hours every 6

months (more frequently if the storage temperature is >40 °C).

Setting Up Procedures

Leave unconnected

Connection Connection

Note: † If pre-set, the ‘SETUP’ security code input screen will be displayed. Enter the 3 digit security

code using the ‘+’,‘-’ and ‘NEXT‘ keys. Press the ‘OK’ key to display the ‘SETUP‘

screen.

Setup Screens

Any changes made to the ‘Setup’ screens will be retained. Memory contents will only be lost in the

unlikely event of a power loss combining a failure of the main and the backup battery. When power is

restored, Setup conditions will revert to the default settings i.e. All tests enabled , all voltages enabled,

First PI value T1 = 1minute, Second value T2 = 10 minutes, Stop time (T3) = 10 minutes, and

enhanced test mode.

Setup Language §

1. From the first ‘Menu’ screen, use the left hand st cursor keys to select and highlight ‘SETUP’.

2. Press the ‘CHANGE’ key. †§ The ‘LANGUAGE SELECTION‘ screen is displayed.

3. Use the left hand cursor keys to select and highlight the required language.

4. Press the ‘YES’ key. The ‘SETUP‘ screen is displayed.

Setup IR, SV and DD Tests

Simple or Enhanced mode can be selected for each type of test (except DD test). ‘SIMPLE’ mode

provides basic test results during, and on completion of a test. ‘ENHANCED’ mode provides basic

test results and a graph plot and a Bargraph as the test progresses. Individual voltage ranges for

each type of test can be switched Off or On as required.

1. From the ‘Menu’screen, use the left hand cursor keys to select and highlight ‘SETUP’.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Use the left hand cursor keys to select and highlight the required test.

4. Press the ‘CHANGE’ key. The ‘SETUP MODE‘ option screen for the selected test is

displayed.

5. Press the ‘SIMPLE’or the ‘ENHANCED’key as required. The ‘TEST RANGES’screen is

displayed. Note:- selecting the ‘DISABLE‘ key will disable and remove the test from the

‘Menu’screen. See ‘Disable a Test’.

6. Use the left hand cursor keys to individually select and highlight any voltage ranges to be

switched Off or On. Press the ‘On’ or ‘OFF’ key, as appropriate.

7. On competion, press the ‘END‘ key to return to the ‘SETUP‘ screen.

8. Press the ‘END‘ key to return to the ‘Menu’ screen.

Setting Up Procedures

Example showing the setup of an enhanced SV Test

Setup PI Test

1. From the ‘Menu’ screen, use the left hand cursor keys to select and highlight ‘SETUP‘.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Use the left hand cursor keys to select and highlight ‘PI’. Press the ‘CHANGE’ key. The

‘PI TEST SETUP‘ screen is displayed.

4. Press the ‘PI TEST TIMES‘ key. The ‘PI TEST TIMES‘ screen is displayed.

5. Press the ‘NEXT‘ key to highlight and select the First Value, the Second Value or the Stop

Time as required.

6. Using the ‘+’ et ‘-’ keys, adjust the timing as required.

7. Press the ‘OK’ key to return to the ‘PI TEST SETUP‘ screen.

8. Use the left hand cursor keys to select and highlight ‘PI‘. Press the ‘CHANGE’ key. The ‘PI

TEST SETUP‘ screen is displayed.

9. Press the ‘SET PI TEST‘ key. The ‘PI TEST SETUP MODE‘ screen is displayed.

10. Press the ‘SIMPLE’ or the ’ENHANCED‘ key as required ‘TEST RANGES‘ screen is

displayed. Note:- selecting the ‘DISABLE‘ key will disable and remove the IP test from the

‘Menu’ screen. See ‘Disable the Test‘.

11. Use the left hand cursor keys to individually select and highlight any voltage ranges to be

switched Off or On. Press the ‘ON’ or ‘OFF’ key, as appropriate.

12. On completion, press the ‘END‘ key to return to the ‘SETUP’ screen.

13. Press the ‘END‘ key to return to the ‘Menu’ screen.

Disable a Test mode

When a test mode is disabled, it is removed fromthe ‘Menu’ screen.

1. From the ‘Menu’ screen, use the left hand cursor keys to select and highlight ‘SETUP‘.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Use the left hand cursor keys to select the test to be disabled.

4. Press the ‘CHANGE’ key. The ‘SETUP MODE‘ screen is displayed.

5. Press the ‘DISABLE‘ key. The ‘SETUP‘ screen is displayed.

6. Press the ‘END‘ key to return to the ‘Menu’ screen.

Alternatively, a test can be disabled by individually setting each test voltage to ‘OFF’.

Setting Up Procedures

Example showing the disabling of a PI Test

Enable a Test mode

1. From the ‘Menu’ screen, use the left hand cursor keys to select and highlight ‘SETUP‘.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Use the left hand cursor keys to select the test (identified as OFF) to be enabled.

4. Press the ‘CHANGE’ key. The ‘SETUP MODE‘ screen is displayed.

5. Press the ‘SIMPLE’ , or the ‘ENHANCED‘ key, as required. The ‘TEST RANGES‘ screen is

displayed.

6. Use the left hand cursor keys to individually select and highlight any voltage ranges to be

switched Off or On. Press the ‘ON’ or ‘OFF’ key, as appropriate.

7. On completion, press the ‘END‘ key to return tothe ‘SETUP‘ screen.

8. Press the ‘END‘ key to return back to the ‘Menu’ screen.

Alternatively, a test can be enabled by individually setting at least one test voltage to ‘ON’.

Example showing the enabling of a DD Test

Delete Stored Test results

1. From the ‘Menu’ screen, use the left hand cursor keys to select and highlight ‘SETUP‘.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Use the left hand cursor keys to select and highlight ‘TESTS STORED‘. Press the ‘CHANGE’

key. The ‘DELETE ALL TESTS - CONFIRM‘ screen is displayed.

4. Accept or reject the deletion by pressing the ‘YES‘ or the ’NO‘ key. The ‘SETUP MODE’

screen is displayed.

5. On completion press ‘END’key to return back to the ‘Menu’ screen.

Set / Reset Date and Time

1. From the ‘Menu’ screen, use the left hand cursor keys to select and highlight ‘SETUP’.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Use the left hand cursor keys to select the current Date and Tiime.

4. Press the ‘CHANGE’ key. †§ The ‘SETUP MODE‘. ‘SET CLOCK’ screen is displayed.

5. Press the ‘NEXT‘ key to highlight and select the Time / Date component to be adjusted.

6. Using the ‘+’ and ‘-’ keys, adjust the time / Date as required.

7. Press the ‘END’ key to return to the ‘SETUP‘ screen.

8. Press the ‘END’ key to return back to the ‘Menu’ screen.

Note:- Date format can be also be changed as required. See ‘Set / Reset Date Format’.

Set / Reset Printer Baud Rate

This is the communication rate used when retrieving results to a serial printer.

1. From the ‘Menu’, screen, use the left hand cursor keys to select and highlight ‘SETUP‘.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Press the ‘NEXT‘ key. Use the left hand cursor keys to select and highlight ‘PRINTER

BAUD‘.

4. Press the ‘CHANGE’ key. †§ The ‘PRINTER BAUD‘ screen is displayed.

5. Use the ‘NEXT‘ key to select and highlight the Baud Rate as required.

6. Press the ‘END’ key.

7. Press the ‘END’ key to return back to the ‘Menu’ screen.

Set / Reset PC Baud Rate

This is the communication speed to your PC when retrieving results to a PC file and does not affect

the speed when using the S1-5010 with the remote control software. The default Baud rate is 9600.

1. From the ‘Menu’ screen, use the left hand cursor keys to select and highlight ‘SETUP‘.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Press the ‘NEXT‘ key. Use the left hand cursor keys to select and highlight ‘PC BAUD‘.

4. Press the ‘CHANGE’ key. The ‘PC BAUD‘ screen is displayed.

5. Use the ‘NEXT‘ key to select and highlight the Baud Rate as required.

6. Press the ‘END‘ key.

7. Press the ‘END‘ key to return back to the ‘Menu’ screen.

Security Codes

There are two security code systems to inhibit access by unauthorized persons. The user definable 3

digit ‘Power On’code controls access entry into the instrument. The user definable 3 digit ‘Setup’

code controls access to the Setup displays.

Set / Reset ‘Power On’ Code

to set or re-set the 3 digit ‘Power On’ code to control access enty into the instrument the ‘POWER ON

SECURITY CODE’ is switched to On in the ‘Setup’ mode. When the instrument is switched Off and

On again, the new code is entered, to operate the instrument. This ‘Power On’code must then be

entered by anyone wishing to use the instrument.

1. From the ‘Menu’, screen, use the left hand cursor keys to select and highlight ‘SETUP‘.

2. Press the ‘CHANGE’ key. †§ The ‘SETUP‘ screen is displayed.

3. Press the ‘NEXT‘ key. The ‘SETUP MODE‘ screen is displayed.

4. Use the left hand cursor keys to select ‘POWER ON SECURITY CODE‘. Press the ‘CHANGE’

key to set the code to ‘ON‘ (or ‘OFF‘ as required). If an existing code is to be changed, set

the code to OFF; exit the screen; return back to the screen and then set the code back to ‘ON‘.

5. Press the ‘END‘ key to exit back to the ‘Menu’ screen.

6. Switch the instrument Off, pause, and then switch back On again. The ‘ENTER THE SECURITY

CODE‘ input screen is displayed.

7. Enter (and remember) the new 3 digit security code using the ‘+’,‘-’ and ‘NEXT‘ keys.

On completion, press the ‘OK’ key. The instrument powers up and the ‘Menu’ screen is

displayed.

Setting Up Procedures

Inhaltsverzeichnis

Andere Megger Prüfgeräte Handbücher

Megger

Megger T22/13B Bedienungsanleitung

Megger

Megger BM15 Bedienungsanleitung

Megger

Megger T 99/1 Bedienungsanleitung

Megger

Megger MTO210 Bedienungsanleitung

Megger

Megger TPT320 Bedienungsanleitung

Megger

Megger MHP1 Bedienungsanleitung

Megger

Megger S1-554/2 Bedienungsanleitung

Megger

Megger OCR15D Bedienungsanleitung

Megger

Megger DET3 Series Bedienungsanleitung

Megger

Megger SMART THUMP ST25-30 Bedienungsanleitung

Megger

Megger MFT-X1 Bedienungsanleitung

Megger

Megger TTR20 Bedienungsanleitung

Megger

Megger BITE5 Bedienungsanleitung

Megger

Megger VLF Sinus Bedienungsanleitung

Megger

Megger MFT1700 series Bedienungsanleitung

Megger

Megger LT300 Bedienungsanleitung

Megger

Megger LT310 Bedienungsanleitung

Megger

Megger ODEN AT Bedienungsanleitung

Megger

Megger PFL22M1500 Series Bedienungsanleitung

Megger

Megger INGVAR Bedienungsanleitung

Megger

Megger OTS100AF Bedienungsanleitung

Megger

Megger BMM500 Series Bedienungsanleitung

Megger

Megger MET1000 Bedienungsanleitung

Megger

Megger DET2/3 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung