Megger S1-554/2 Bedienungsanleitung

S1-554/2

5kV Digital Insulation Tester

USER MANUAL

GSAFETY WARNINGS

Safety Warning must be observed during use.

nThe circuit under test must be switched off, de-energised, isolated and checked to be safe before insulation test connections are made. Make sure the

circuit is not re-energised whilst the instrument is connected.

nCircuit connections must not be touched during an insulation test.

nAfter completing a test, capacitive circuits must be completely discharged before disconnecting the test leads. Capacitive charges can be lethal.

nTested items should be firmly shorted out with a shorting link, after discharge, until required for use. This is to guard against any stored dielectric

absorption charge subsequently being released thereby raising the voltage to potentially dangerous levels.

nThe voltage indicator and automatic discharge features should be regarded as additional safety features and not a substitute for normal safe working

practice.

nIt is rare, but in certain circumstances, breakdown of the circuit under test may cause the instrument to terminate the test in an uncontrolled manner,

possibly causing a loss of display while the circuit remains energised. In this event, the unit must be turned off and the circuit discharged manually.

nTest leads, including crocodile clips, must be in good order, clean and with no broken or cracked insulation.

nThe instrument should not be used if any partof it is damaged.

nInsulation testing in wet weather conditions might be hazardous. It is recommended that this instrument is not used in these circumstances. If this is

unavoidable, the user must takeall necessary precautions.

nThis instrument is not intrinsically safe and must not be used in hazardous atmospheres.

NOTE

THE INSTRUMENT MUST ONLYBE USED BY SUITABLY TRAINED AND COMPETENT PERSONS.

Users of this equipment and/or their employers are reminded that National Health and Safety Legislation requires them to carry out valid risk assessments of

all electrical work so as to identify potential sources of electrical danger and risk of electrical injurysuch as inadvertent shortcircuits. Where the assessments

show that the risk is significant then the use of fused test leads may be appropriate.

Insulation resistance ‘IR’ test 15

Firmware filtering 15

Breakdown mode / burn mode 16

Alarm limit mode 16

Step voltage ‘SV’ test 16

Polarisation index ‘PI’ test, and dielectric absorption

ratio ‘DAR’ test 16

Dielectric discharge ‘DD’ test 17

Measurements above 100 GΩ17

Circuit block diagram 18

Specifications 19

Accessories 20

Repair and warranty 21

Symbols used on the instrument are:

FCaution: risk of electric shock

GCaution: refer to accompanying notes

tEquipment protected throughout by Double

Insulation (Class II)

cEquipment complies with current EU directives.

Terms used in this manual

The word must is used to indicate that the instructions following should

be followed under all circumstances. Failure to follow these instructions

could result in damage to the instrument and / or a hazard to the operator.

The word should is used to indicate that the instructions indicate best

practice.

CONTENTS

Safety warnings 2

Introduction 4

General description 4

Features 4

Cleaning 5

Power lead and battery charging 5

Instrument controls and indicators 6

Power On/Off button 7

Test voltage sand tbuttons 7

Test start / stop button 7

Ω/I button 7

Bbutton 10

Fn button 10

Mode button 10

Timer sand tbuttons 11

Record button 11

Recording to on-board memory 11

Downloading results 11

Deleting results 11

Recording to a PC 12

High voltage warning LED 12

Line input present LED 12

Test terminals 12

Guard terminal 12

RS232 / USB connections 13

Battery bar graph 13

Voltage at terminals 13

Timer indicator 13

Digital display 13

Analogue display 14

Secondarydisplay 14

Pre-Test / during test key action table 14

Test mode summary 15

Hardware filter 15

capacitance, time constant, voltage, timer measurements, and figure of

merit measurements such as polarisation index.

Features

nContinuous resistance or current measurement on main display.

nOptional resistance, current, or figure of merit measurements on

secondary display.

nStandard test voltages – 250 V, 500 V, 1 kV, 2.5 kV, 5 kV

nNon-standard test voltages – selectable between 50 V and 1 kV in 10 V

steps, and selectable between 1 kV and 5 kV in 25 V steps.

nTest modes include insulation resistance, polarisation index, step

voltage and dielectric discharge.

n4mA rms hardware noise current filter (selectable)

nFirmware filter 10, 30, and 100 seconds (optional)

nThe dielectric absorption ratio is automatically calculated if the

corresponding timers are set.

nEither burn or breakdown selectable in insulation resistance mode.

nInsulation ‘Alarm Limit’ available in insulation resistance mode.

nProgrammable timers include a main test duration timer,plus T1 and

T2 timers for time resistance method type tests.

nLoad capacitance and time constant measurements – displayed at end

of test.

nLCD backlight.

nData storage, data retrieval and real time data output.

nUSB or RS232 communications.

nBattery level / charge level indicator.

INTRODUCTION

General Description

The S1-554/2 is a microprocessor controlled 5 kV insulation tester offering

measurement capability of up to 15 TΩ.The instrument performs

automatic tests and has data storage and data retrieval facilities.

Polarization index and dielectric discharge tests are performed

automatically, and test duration and voltages can be adjusted according to

user preference for these tests. A step voltage test can be performed

automatically, with a default voltage of 1 kV, and test duration of 5 minutes.

It is possible for the user to set different voltages and test durations for the

step voltage test.

The S1-554/2 incorporates a hardware filter designed to tolerate at least

4mA rms of noise current at 50Hz and above. This filter is enabled by

default, but may be switched off in order to speed up the settling time

when there is little noise current. The Insulation Resistance mode offers

additional firmware filtering to average out slow variations during testing.

The S1-554/2 can be powered from the mains supply or by its own internal

rechargeable battery, which provides for at least 6 hours of continuous

testing with a 100 MΩload. A battery level indicator on the LCD display

indicates battery capacity. Connecting power to the mains supply

connector will automatically charge the battery whether the instrument is

switched ‘on’ or ‘off’, except during testing. A high level of internal

isolation allows the instrument to be used while the unit is supplied from

the mains. An internal batterymanagement system switches the

instrument off after ten minutes of inactivity. If the battery approaches a

very low state of charge the instrument turns itself off,and mains power

must be applied before the instrument can be used again. Recorded test

results and settings will not be lost when the instrument is switched off.

Acomprehensive LCD display shows resistance, current, filter setting,

If the power lead supplied is not suitable for your mains connection, do

not use an adaptor. Always use a power lead fitted with the correct plug.

The instrument is fitted with a two-pin IEC60320 power inlet. Most power

leads are made with three-core cable, so the ground connection will not

be used.

Power lead connection table

Connection UK/International USA

Earth/Ground Yellow/Green Green

Neutral Blue White

Live (Line) Brown Black

If using a fused plug, ensure that it is fitted with a 3 Amp fuse.

The instrument can be powered from 85 - 265 Vrms a.c. at 50/60 Hz. The

battery will charge as long as the mains supply is connected, except when

atest is in progress. The power On/Off button has a green LED, which

illuminates when mains power is present. For optimum battery life, charge

the battery after each use. A completely exhausted batterywill take14

hours to recharge.

POWER LEAD AND BATTERY CHARGING

Cleaning

Disconnect the instrument and wipe it with a clean cloth slightly damped

with soapy water or Isopropyl alcohol (IPA).

INSTRUMENT CONTROLS AND INDICATORS

Measurement terminals

-ve guard +ve

RS232

USB

Line

input

Time sand

tselectors

Voltage s

tselectors Line input

Present

indicator

Power on/off

Ω/I selector

Burn indicator Alarm Data recording

Test modes

Voltage at

terminals

Battery level

Breakdown

indicator

High voltage

warning

indicator

High

voltage

warning

indicator

Analogue

display

Timers

Main, T1,

Dielectric

absorption

ratio/T1 timer

Digital

display

Polarisation

index/timer T2

Time

constant

Capacitance

display

Data record

High voltage

warning indicator

Test start/stop

ModeFunction

Backlight

on/off

S1-554

test voltage is changed during a test, the new test voltage will be displayed

briefly.

When the test has stopped, the display continues to show the voltage

present on the test leads. Pressing either test voltage sor tbutton will

then display the test voltage immediately before the end of the test.

Test start / stop button

Atest will only start if this button is pressed, held and then released as

soon as the red high voltage warning indicator LED lights. The LCD and

red LED high voltage warning indicators flash when the test starts.

Atest will not startif the button is released before the red LED shows, or

pressed continuously for longer than 5 seconds. This is a safety feature to

prevent a test being started inadvertently.

The presence of a voltage greater than 50 V on the test leads is indicated

with flashing high voltage warning indicators. Testing is disabled if the

external voltage exceeds 80 V.

Testing will stop if the test start/stop button is pressed again, the preset

test time is reached, or, if the unit is not in burn mode, insulation

breakdown is detected.

When a test has finished, the instrument will discharge the load, which

may take some time. The operator must always check the load has been

discharged before touching the test leads.

Ω/I button

Pressing this button toggles the digital and secondary displays. The details

available when scrolling the secondarydisplay will depend upon the test

mode selected, whether timers T1 and T2 have been set, and the duration

Power On/Off button

The instrument will only turn on if this button is pressed, held and then

released when the display responds. The instrument will not turn on if the

button is released before the display responds, or if the button is held

down for too long. This is a safety feature to prevent the instrument being

inadvertently turned on.

The instrument is turned off either by pressing the button again, or if the

instrument is running on the battery, by timing out after 10 minutes of

inactivity.

Upon switching the instrument on the display will first show ‘Ini’ while it

undergoes a self-checking routine. When Ini disappears, the instrument is

ready for use.

Test voltage sand tbuttons

Using these buttons one of five test voltages can be selected: 250 V, 500 V,

1kV, 2.5 kV, and 5 kV. The selected voltage is shown on the display.

A non standard voltage between 50 V and 5 kV can be selected by holding

down the ‘Fn’ function button whilst operating the buttons. The selectable

voltage is adjustable in 10 V steps between 50 V and 1 kV, and adjustable in

25 V steps between 1 kV and 5 kV. An auto repeat facility is enabled when

the button is held down, allowing faster travel through the range.

If there is an external voltage greater than 50 V on the test leads, the high

voltage warning indicators are flashed, and the display shows this voltage

instead. The instrument will not perform a test if this voltage is greater

than 80 V.

During a test the display shows the actual voltage on the test leads. If the

Figure 1 - The result of an insulation resistance test (IR)

Test settings: T1 and T2 times set in order to measure the DAR

Test conditions: test runs for longer than 10 minutes as this is required for

aPI reading.

of the test. The digital display toggles between insulation resistance and

current.

In the ‘IR’, ‘PI’, and ‘DD’ modes the secondary display initially shows the

PI (polarity index), DAR (dielectric absorption ratio), and, on completion

of the test, the TC (time constant) and capacitance measurements. Further

presses of the Ω/I button cycles the display through insulation resistances,

currents, and the filter setting.

In the ‘SV’ (step voltage) mode, the secondary display cycles through

insulation resistances, currents, and the filter setting.

Figures 1 to 4 illustrate the display status for sequential ‘Ω/I’ key presses in

the different modes.

Press Ω/I

Figure 2 - The result of a polarity index test (PI)

Test settings: T1 and T2 times set in order to measure the DAR

Test conditions: timer defaults to 10 minutes, as this is required for a PI

reading

Figure 3 - The result of a dielectric discharge test (DD)

Test settings: T1 and T2 times set in order to measure the DAR

Test condition: test runs for longer than 10 minutes as this is required for

aPI reading.

Press Ω/I

test voltage buttons. ‘Tsand ‘Ttrepresent the timer buttons.

Button Press Function Comment

Fn + VsIncrement in 10 V steps Voltage range between

50 and 1000 V

Fn + VtDecrement in 10 V steps Voltage range between

50 and 1000 V

Fn + VsIncrement in 25 V steps Voltage range between

1000 and 5000 V

Fn + VtDecrement in 25 V steps Voltage range between

1000 and 5000 V

Fn + Tsor TtCycle through timers Select main timer, T1

or T2

Fn + Mode Cycle through IR modes Select breakdown, burn

or alarmlimit for IR test

Fn + Ω/I Cycle through filter options Additional filtering

options are available in

IR mode

Fn + Download mode See ‘Downloading

results’

Fn + Clear stored data The ‘record’ button is

pressed twice

Mode button

Press down on the ‘MODE’ button to cycle through and select the test

mode. Modes of test to be chosen from include an insulation resistance ‘IR’

test, a polarization index ‘PI’ test, a step voltage ‘SV’ test, and a dielectric

discharge ‘DD’ test.

The insulation resistance ‘IR’ test operates in either ‘burn’ or ‘breakdown’

Figure 4 - The result of a step voltage (SV) test

Test condition: timer defaults to 5 minutes and test voltage defaults to

1000 V.

Bbutton

Pressing this button toggles the display backlight on and off.

Fn button

The function button when pressed allows other keys to perform another

function. This is summarized in the table below. ‘Vsand ‘Vtrepresent the

Press Ω/I

Inhaltsverzeichnis

Andere Megger Prüfgeräte Handbücher

Megger

Megger CM500 Bedienungsanleitung

Megger

Megger MPRT 8415 Bedienungsanleitung

Megger

Megger Surgeflex 12 Bedienungsanleitung

Megger

Megger PFL40A Bedienungsanleitung

Megger

Megger BITE 2 Bedienungsanleitung

Megger

Megger EZ-ThumpV3 Bedienungsanleitung

Megger

Megger CDAX 605 Bedienungsanleitung

Megger

Megger SWG 1750 C Bedienungsanleitung

Megger

Megger DET3TA Bedienungsanleitung

Megger

Megger ADX15 Bedienungsanleitung

Megger

Megger VF6 EX Bedienungsanleitung

Megger

Megger MIT510/2 Bedienungsanleitung

Megger

Megger WM6 Bedienungsanleitung

Megger

Megger VLF Sinus 62 kV Bedienungsanleitung

Megger

Megger HPG AC Series Bedienungsanleitung

Megger

Megger PAT410 Bedienungsanleitung

Megger

Megger PAT4DV/3 Bedienungsanleitung

Megger

Megger SG32-1500M Bedienungsanleitung

Megger

Megger S1-5010 Bedienungsanleitung

Megger

Megger TPT320 Bedienungsanleitung

Megger

Megger SVERKER 650 Bedienungsanleitung

Megger

Megger TTR20 Bedienungsanleitung

Megger

Megger DET2/3-ETK-50M Bedienungsanleitung

Megger

Megger MFT1700 series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung