Meitav-tec FMT24-SUPER Bedienungsanleitung

FMT24-SUPER

Owner’s manual & Technician Settings

SELECT

Aux

Operating instructions

ON-OFF

Press the [SELECT] button – the mode will flash.

Using the [+] and [-] buttons switch between modes:

“Cool”………………… Cooling

“Heat”………………… Heating

“Cool” & “Heat”……… Auto mode

“Fan”…………………. Fan only

Note: During demand for cooling or heating, the

active mode will flash.

Press the [SELECT] button again – “Auto Fan” or

“Fan” will flash.

Using the [+] and [-] buttons switch between:

“Fan”…………….…… The fan will work

continuously.

“Auto Fan”…………… The fan will work on

demand for cooling or heating.

Note: Auto fan cannot be selected in Fan only mode.

Press the [ON] button to turn the thermostat ON or OFF.

Modes and Auto fan (fan on demand)

Set point

Press the [+] or [-] buttons once to view the set point temperature.

Press again to adjust the set point.

Cool

Heat

Cool

Heat

Fan

Cool Heat Auto

mode

Fan only

Tel: +972-3-9626462

Fax: +972-3-9626620

support@meitavtec.com

File: FMT24-SUPER_operating manual.vsd

FMT24-SUPER

Owner’s manual & Technnician Settings

Pg. 2

Auto fan

OFF

Auto fan

Auto FanFan

SELECT

Aux

Make sure the set point temperature is different than 10°C (50°F).

Press and hold the [SELECT] button to activate emergency heat – release the

[Select] button when "EH" appears on display.

Press and hold the [SELECT] button again to deactivate emergency heat –

release [Select] button when “H” appears on display.

Notes:

1. Emergency Heat can be activated in heat pump configuration only (please

refer to the technician settings section in this manual) and in heating mode.

2. When the Emergency Heat is active, the compressor will stop and only the

heat element will be used for heating. The display will alternate between “EH”

and the room temperature.

Emergency heat – to be used in extremely low outdoor temperatures

Emergency

heat

Operating instructions (Cont’)

Tel: +972-3-9626462

Fax: +972-3-9626620

support@meitavtec.com

FMT24-SUPER

Owner’s manual & Technnician Settings

Pg. 3

Press and hold the [ON] button (5 seconds) to activate economy mode –

“EC” will appear on display.

Press and hold the [ON] button again to return to normal display.

Note: In economy mode, the set-point temperature for cooling = 29°C (85°F)

and the set-point temperature for heating = 13°C (55°F).

Economy mode

When the measured temperature is less than 6°C (45°F) “AL” will flash.

The indication will automatically disappear when the measured temperature is

higher than 8°C (48°F).

Low temperature alarm indication

Emergency

heat

Economy

mode

Tel: +972-3-9626462

Fax: +972-3-9626620

support@meitavtec.com

FMT24-SUPER

Owner’s manual & Technnician Settings

Pg. 4

Installation

The FMT24-SUPER is designed for flush mounting in the room to be controlled. It should be located where

the occupant can easily read the LCD display and use the controls. The module should be placed in such

location which represents the room general conditions. Cold or warm air draughts; radiant heat and direct

sunlight should be avoided.

General points to follow:

- Disconnect power to the main board before installing the unit.

- The unit MUST be fitted into a standard electrical box (Carlon – B114R or similar)

- The unit should not be installed on an outside wall or where there is an air draft.

- The unit must not be exposed to a direct sunlight.

- The standard height to install this unit is 1.5 meter (5 feet) from the floor.

Installation procedure:

A. Connect the wires as shown in the enclosed wiring diagram. All terminals accept 1x0.5 mm2/24 AWG.

B. Place the thermostat in the electrical box and tighten up the 2 screws.

C. Adapt the front frame-panel into its place, by pushing it towards the wall.

Tel: +972-3-9626462

Fax: +972-3-9626620

support@meitavtec.com

FMT24-SUPER

Owner’s manual & Technnician Settings

Pg. 5

Wiring

Before connecting or disconnecting any wires, ensure that all power supplies have been switched off and all

wires are potential-free to prevent equipment damage and avoid electrical shock.

Do not run wiring close to transformers or high frequency generating equipment. Complete and verify all

wiring connections before applying power to the controller to which the module is connected.

Fan

Compressor 1

Heat element 1

Compressor 2

**Main supply 24VAC

Heat element 2

Notes:

1. For a non heat pump system with one heat element, leave terminal “W2” free.

2. When Emergency heat mode is selected, the compressor and heat pump will close and the heat

element will turn ON (Emergency heat is available in heat pump configuration only.

3. RC-RH, - When using one transformer, RC,RH terminals must be shorted.

Fan

Compressor 1

Heat pump

Compressor 2

**Main supply 24VAC

Heat element (2nd stage) (Emergency heat)

System without heat pump

(heat elements only)

System with heat pump

Technician Settings

Tel: +972-3-9626462

Fax: +972-3-9626620

support@meitavtec.com

FMT24-SUPER

Owner’s manual & Technnician Settings

Pg. 6

Enter technician settings mode

Adjust the set point temperature to 10°C (50°F)

Press and hold the [SELECT] button for 5 seconds to enter technician

settings mode.

Temperature limit for cooling

“Cool” will flash.

Use the [+] and [-] buttons to adjust the temperature limit for cooling.

Range: 10...30°C (50...88°F), Default 10°C (50°F).

Limit Cool (°C) Limit Cool (°F)

Cool Cool

Enter tech.

settings

Enter tech.

settings

°C °F

Temperature limit for heating

Press the [SELECT] button again – “Heat” will flash.

Use the [+] and [-] buttons to adjust the temperature limit for heating.

Range: 10...30°C (50...88°F), Default 30°C (88°F).

Temperature scale

Heat Heat

Limit Heat (°C) Limit Heat (°F)

Press the [SELECT] button again – “C” or “F” will appear on display.

Use the [+] and [-] buttons to select between:

“C”…….… Celsius

“F”…...….. Fahrenheit

Celsius Fahrenheit

Offset for calibration of measured temperature

Press the [Mode] button again – the offset will appear on display.

Use the [+] and [-] buttons to adjust the offset.

Range: -6…+6°C (-6…+6°F), Default 0°C (0°F).

Offset(°C) Offset (°F)

Terminal “W1” configuration - Heat pump or heat element

Press the [SELECT] button again – “HC” or “HP” will appear on display.

Use the [+] and [-] buttons to select between:

“HC”…….…Heat element connected to “W1”

“HP”…...…..Heat pump connected to “W1”

Heat element Heat pump

Technician Settings (Cont’)

Tel: +972-3-9626462

Fax: +972-3-9626620

support@meitavtec.com

FMT24-SUPER

Owner’s manual & Technnician Settings

Pg. 7

Heater type – Electric or Oil/Gas – Selection for non heat pump configurations

Press the [SELECT] button again – “EO” will appear on display.

Use the [+] and [-] buttons to select between:

“E” flashing…….… Electric heater

“O” flashing…...…..Oil/Gas heater

Note:

In Oil/Gas configuration, when Auto fan (fan on demand) is selected,

the fan will stop.

In Electric heat configuration, when Auto fan is selected, the fan will

work on demand for cooling or heating.

This selection will not be available when heat pump is connected to

“W1” terminal (Previous technician selection).

Heat pump in cool or in heat – Selection for heat pump configuration only

Press the [SELECT] button again – “HC” will appear on display.

Use the [+] and [-] buttons to select between:

“H” flashing…….… Heat pump active in heat (B)

“C” flashing…...…..Heat pump active in cool (O)

Oil/Gas

heater

Electric

heater

Active

in cool

Active

in heat

delay

3 Minutes

delay

Enable/Disable compressor delay

Press the [SELECT] button again – “30” will appear on display.

Use the [+] and [-] buttons to select between:

“3” flashing…….… 3 Minutes compressor delay)

“0” flashing…...….. No delay

Press the [SELECT] button again – “30” will appear onto return to normal display.

Tel: +972-3-9626462

Fax: +972-3-9626620

support@meitavtec.com

www.meitavtec.com

Inhaltsverzeichnis

Andere meitav-tec Thermostat Handbücher

meitav-tec

meitav-tec ETN-24-PM-H-1S Sicherheitsleitfaden

meitav-tec

meitav-tec Haften TRE24-PROG-HC11 Bedienungsanleitung

meitav-tec

meitav-tec ETN-24-PD-1S Bedienungsanleitung

meitav-tec

meitav-tec FMH-220 Fan-Coil Super 3 Bedienungsanleitung

meitav-tec

meitav-tec TED220-HC11-3S Bedienungsanleitung

meitav-tec

meitav-tec TAT-SUPER Bedienungsanleitung

meitav-tec

meitav-tec ETN-P Series Sicherheitsleitfaden

meitav-tec

meitav-tec BDIR Gebrauchsanweisung

meitav-tec

meitav-tec FMH-220-FAN-COIL-SUPER 3 Bedienungsanleitung

meitav-tec

meitav-tec ETNC24-SUPER-MDB-01 Bedienungsanleitung

meitav-tec

meitav-tec FMH24-PD-1S-IR Bedienungsanleitung

meitav-tec

meitav-tec ETN-24-SUPER-PROG Sicherheitsleitfaden

meitav-tec

meitav-tec MTSCV/SUPER/PROG/HU/PIR Bedienungsanleitung

meitav-tec

meitav-tec ETN24 Bedienungsanleitung

meitav-tec

meitav-tec FMH-24-C2-3S-IR Bedienungsanleitung

meitav-tec

meitav-tec FMH-220 Fan-Coil Super 3 Bedienungsanleitung

meitav-tec

meitav-tec ETNC-SUPER-PROG-HU-PIR Bedienungsanleitung

meitav-tec

meitav-tec ETN24-PM-HP-SUPER-BL Bedienungsanleitung

meitav-tec

meitav-tec ETN24-P-3S-HU Bedienungsanleitung

meitav-tec

meitav-tec SUPER-SI Series Handbuch

meitav-tec

meitav-tec ETN-24-SUPER-SI Series Bedienungsanleitung

meitav-tec

meitav-tec ETNC24-FC-BAC-PIR-02 Bedienungsanleitung

meitav-tec

meitav-tec ETN-12-P-3S Bedienungsanleitung

meitav-tec

meitav-tec MTSC/SUPER/HU Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

meitav-tec FMT24-SUPER Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken