Meraki MR53 Handbuch

Meraki MR53

Hardware Installation Guide

Trademarks

Meraki, Meraki MR53, Meraki Cloud Controller, and Meraki Mesh are trademarks of Cisco Systems, Inc.

Other brand and product names are registered trademarks or trademarks of their respective holders.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, Cisco Systems reserves the right to make

changes to the products described in this document without notice. Cisco Systems does not assume any liability that may

occur due to the use or application of the product(s) or circult layout(s) described herein.

Warranty

Meraki, Inc. provides a lifetime warranty on this product. Warranty details may be found at www.meraki.com/legal.

Table of Contents

1 Scope of Document and Related Publications 4

2 MR53 Overview 5

2.1 Package Contents 5

2.2 Understanding the MR53 5

2.3 Security Features 7

2.4 Ethernet Ports 7

2.5 Power Source Options 7

2.6 Factory Reset Button 7

2.7 LED Indicators and Run Dark Mode 7

3 Pre-Install Preparation 8

3.1 Conﬁgure Your Network in Dashboard 8

3.2 Check and Upgrade Firmware 8

3.3 Check and Conﬁgure Firewall Settings 8

3.4 Assigning IP Addresses to MR53s 9

3.4.1 Dynamic Assignment 9

3.4.2Static Assignment 9

3.4.3 Static IP Assignment via DHCP Reservations 9

3.5 Collect Tools 10

3.6 Collect Additional Hardware for Installation 10

4 Installation Instructions 11

4.1 Choose Your Mounting Location 11

4.2 Install the MR53 11

4.2.1 Attach the Mount Plate 11

4.2.1.1 Wall or Solid Ceiling Mount Using Mount Plate 13

4.2.1.2 Drop Ceiling Mount Using Mount Plate 14

4.2.1.3 Electrical Junction Box Mount Using Mount Plate 18

4.2.2 Power the MR53 20

4.2.2.1 Powering the MR53 with Meraki AC Adapter 21

4.2.2.2 Powering the MR53 with Meraki 802.3af Power over Ethernet Injector 21

4.2.2.3 Powering the MR53 with an 802.3af Power over Ethernet Switch 22

4.2.3 Mount the MR53 22

4.2.3.1 Assemble Security Hasp to the MR53 22

4.2.3.2 Assemble MR53 to the Mount Plate 23

4.2.3.3 Desk or Shelf Mount 25

4.3 Secure the MR53 26

4.3.1 Security Screw 26

4.3.2 Kensington Lock 26

4.4 Verify Device Functionality and Test Network Coverage 27

5 Troubleshooting 27

1 Scope of Document and Related Publications

The MR53 Hardware Installation Guide describes the installation procedure for the MR53 indoor access point.

Additional reference documents are available online at www.meraki.com/library/product.

MR53 access point

Drop ceiling mounting kit

2 MR53 Overview

The Meraki MR53 is an enterprise-class, dual-concurrent 4x4 MIMO 802.11ac indoor access point designed for

high-density deployments in ofﬁces, schools, hospitals and hotels. When connected to the Meraki Cloud Control

ler, the MR53 enables the creation of ultra-high speed, reliable indoor wireless networks quickly, easily and cost-

effectively.

2.1 Package Contents

The MR53 package contains the following:

2.2 Understanding the MR53

MR53 Operation Temperature:

32 ° F to 104 ° F (0 ° C to 40 ° C)

Your Meraki MR53 has the following features:

Kensington lock

hard point

Security screws

Wall screws

Mounting Template

Mounting plate

Your MR53 mount plate has the following features:

MR53 cable access bay

Mount plate attachment

slots (2x)

Access point

mounting posts (2x)

Desk mount feet (4x)

Cable access bay

AC Adapter plug (sold separately)

Power supplied by adapter: 12Vdc, 2.5A

Ethernet 0 port (10/100/1000)

Power supplied by PoE: 37-57 Vdc, 0.6A

Factory Reset Button

Various mounting holes

2.3 Security Features

The MR53 features multiple options for physically securing the access point after installation:

1. Security screw – The accessory kit includes screws that can be used to secure the access point to

the mount plate. Engaging the security screw prevents accidental dislodging and theft.

2. Kensington lock – The access point contains a hard point that allows it to be secured to any nearby

permanent structure using a standard Kensington lock.

2.4 Ethernet Ports

The MR53 features a Gigabit Ethernet RJ45 port that accepts 802.3at power (labeled “PoE”). This port should

be used for uplink to your WAN connection.

2.5 Power Source Options

The MR53 access point can be powered using either the Meraki AC Adapter or 802.3at PoE Injector (both sold

separately) or a third-party 802.3at PoE switch.

2.6 Factory Reset Button

If the button is pressed and held for at least ﬁve seconds and then released, the MR53 will reboot and be

restored to its original factory settings by deleting all conﬁguration information stored on the unit.

3 Pre-Install Preparation

You should complete the following steps before going on-site to perform an installation.

3.1 Conﬁgure Your Network in Dashboard

The following is a brief overview only of the steps required to add an MR53 to your network. For detailed

instructions about creating, conﬁguring and managing Meraki wireless networks, refer to the Meraki Cloud

Controller Manual (meraki.com/library/product).

1. Login to http://dashboard.meraki.com. If this is your ﬁrst time, create a new account.

2. Find the network to which you plan to add your APs or create a new network.

3. Add your APs to your network. You will need your Meraki order number (found on your invoice if you

ordered directly from Meraki) or the serial number of each AP, which looks like Qxxx-xxxx-xxxx, and is

found on the bottom of the unit. You will also need your Enterprise Cloud Controller license key, which you

should have received via email from [email protected].

4. Go to the map / ﬂoor plan view and place each AP on the map by clicking and dragging it to the location

where you plan to mount it.

3.2 Check and Upgrade Firmware

To ensure your MR53 performs optimally immediately following installation, Meraki recommends that you

facilitate a ﬁrmware upgrade prior to mounting your MR53.

1. Attach your MR53 to power and a wired Internet connection. See p. 19 of this Hardware Installation

Guide for details.

2. The MR53 will turn on and the Power LED will glow solid orange. If the unit does not require a ﬁrmware

upgrade, the Power LED will turn white within thirty seconds.

* If the unit requires an upgrade, the Power LED will begin blinking orange until the upgrade is complete,

at which point the Power LED will turn solid white. You should allow about an hour for the ﬁrmware

upgrade to complete, depending on the speed of your internet connection.

3.3 Check and Conﬁgure Firewall Settings

If a ﬁrewall is in place, it must allow outgoing connections on particular ports to particular IP addresses.

The most current list of outbound ports and IP addresses can be found here:

http://tinyurl.com/y79une3

3.4 Assigning IP Addresses to MR53s

All gateway MR53s (MR53s with Ethernet connections to the LAN) must be assigned routable IP addresses.

These IP addresses can be dynamically assigned via DHCP or statically assigned.

3.4.1 Dynamic Assignment

When using DHCP, the DHCP server should be conﬁgured to assign a static IP address for each MAC address

belonging to a Meraki AP. Other features of the wireless network such as 802.1x authentication, may rely on the

property that the APs have static IP addresses.

3.4.2 Static Assignment

Static IPs are assigned using the local web server on each AP. The following procedure describes how to set

the static IP:

1. Using a client machine (e.g. a laptop), connect to the AP either wirelessly (by associating to any SSID

broadcast by the AP) or over a wired connection.

If using a wired connection, connect the client machine to the MR53 either through a PoE switch or a Meraki

PoE Injector. If using a PoE switch, plug an Ethernet cable into the MR53’s Ethernet jack, and the other end

into a PoE switch. Then connect the client machine over Ethernet cable to the PoE switch. If using a Meraki

PoE Injector, connect the MR53 to the “PoE” port of the Injector, and the client machine to the “LAN” port.

2. Using a web browser on the client machine, access the AP’s built-in web server by browsing to

http://my.meraki.com. Alternatively, browse to http://10.128.128.128.

3. Click on the “Static IP Conﬁguration” tab. Log in. The default user name is “admin”. The default password is

the AP’s serial number, with hyphens included

4. Conﬁgure the static IP address, net mask, gateway IP address and DNS servers that this AP will use on its

wired connection.

5. If necessary, reconnect the AP to the LAN.

3.4.3 Static IP via DHCP Reservations

Instead of associating to each Meraki AP individually to conﬁgure static IP addresses, an administrator can assign

static IP addresses on the upstream DHCP server. Through “DHCP reservations”, IP addresses are “reserved” for the

MAC addresses of the Meraki APs. Please consult the documentation for the DHCP server to conﬁgure DHCP

reservations.

Phillips

screwdriver

Hammer Drill with 1/4”

(6.3mm) bits

3.6 Collect Additional Hardware for Installation

802.3at PoE power source (either PoE

switch or Meraki 802.3at PoE Injector)

Network cables with RJ45 connectors long

enough for your particular mounting location

3.5 Collect Tools

You will need the following tools to perform an installation:

AC Adapter

Inhaltsverzeichnis

Andere Meraki Drahtloser Zugangspunkt Handbücher

Meraki

Meraki MR62 Bedienungsanleitung

Meraki

Meraki MR76-HW Handbuch

Meraki

Meraki MR14 Handbuch

Meraki

Meraki MR11 Handbuch

Meraki

Meraki Outdoor Handbuch

Meraki

Meraki MR58 Bedienungsanleitung

Meraki

Meraki MR24 Handbuch

Meraki

Meraki MR12 Handbuch

Meraki

Meraki Outdoor Bedienungsanleitung

Meraki

Meraki MR33 Handbuch

Meraki

Meraki MR58 Bedienungsanleitung

Meraki

Meraki MR62 Handbuch

Meraki

Meraki Wall Plug Bedienungsanleitung

Meraki

Meraki MX75 Handbuch

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung