Metabo HPT AC 18DA Bedienungsanleitung

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

Model

Modèle

Modelo AC 18DA

Cordless Caulking Gun

Pistolet à calfeutrer sans ﬁl

Pistola inalámbrica para caulking

Without charger and battery

Sans chargeur et batterie

Sin cargador y baterfa

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand

this manual BEFORE operating the power tool. Please keep this manual available for other

users and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para

que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe

ser guardado en un lugar seguro.

00BookAC18DANA.indb100BookAC18DANA.indb1 2022/03/1015:09:212022/03/1015:09:21

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁcally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and speciﬁcations provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁed plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges

and refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

00BookAC18DANA.indb200BookAC18DANA.indb2 2022/03/1015:09:212022/03/1015:09:21

English

Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-

skid safety shoes, hard hat or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the oﬀ-position before

connecting to power source and/or battery

pack, picking up or carrying the tool.

Carrying power tools with your ﬁnger on the

switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ.

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool before

making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀerent

from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁre when used with

another battery pack.

b) Use power tools only with speciﬁcally

designated battery packs.

Use of any other battery packs may create a risk

of injury and ﬁre.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause burns or a ﬁre.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause

irritation or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁed.

Damaged or modiﬁed batteries may exhibit

unpredictable behaviour resulting in ﬁre,

explosion or risk of injury.

00BookAC18DANA.indb300BookAC18DANA.indb3 2022/03/1015:09:222022/03/1015:09:22

English

f) Do not expose a battery pack or tool to ﬁre or

excessive temperature.

Exposure to ﬁre or temperature above 265 °F may

cause explosion.

g) Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range speciﬁed in the

instructions.

Charging improperly or at temperatures outside

the speciﬁed range may damage the battery and

increase the risk of ﬁre.

6) Service

a)Have your power tool serviced by a

qualiﬁed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or authorized

service providers.

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live”and could

give the operator an electric shock.

2. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

3. NEVER touch moving parts.

NEVER place your hands, ﬁngers or other body parts

near the tool’s moving parts.

4. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard

or safety feature before resuming operation of the

tool.

5. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

6. NEVER use a power tool for applications other

than those speciﬁed.

NEVER use a power tool for applications other than

those speciﬁed in the Instruction Manual.

7. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

8. Keep all screws, bolts and covers tightly in

place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

9. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

10. Holder and accessories must be securely

mounted to the tool.

Prevent potential injuries to yourself or others. Holder

and accessories which have been mounted to the

tool should be secure and tight.

11. Hold the tool ﬁrmly.

12. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that

air can freely ﬂow at all times. Check for dust build-up

frequently.

13. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

metabo HPT authorized service center.

14. NEVER leave tool running unattended. Turn

power oﬀ.

Don’t leave tool until it comes to a complete stop.

15. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

17. ALWAYS wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

00BookAC18DANA.indb400BookAC18DANA.indb4 2022/03/1015:09:222022/03/1015:09:22

English

18. ALWAYS wear a mask or respirator to protect yourself

from dust or potentially harmful particles generated

during operation.

19. ALWAYS ﬁrmly grip the handle while operating.

20. Deﬁnitions for symbols used on this tool

V ..................volts

---.................direct current

no................no load speed

inch/min.......inch per minute

oz.................ounce

21. Because the cordless power tool operates by battery

power, be aware of the fact that it can begin to operate

at any time.

22. Do not use in locations where inﬂammable materials

such as lacquer, paint, benzene, thinner or gasoline

are present.

23. When working at elevated locations, clear the area

of all other people and be aware of conditions below

you.

24. NEVER operate from an unstable footing, such

as when on a ladder or step ladder.

Doing so may cause an injury.

25. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

26. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YFSL.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable battery multi volt type series and BSL18

series. Other type of batteries may burst causing

personal injury and damage.

4. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁre, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁre and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁed in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than but less

than Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating–for example:

1,250 watts = 10 amperes

125 volts

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁed serviceman.

00BookAC18DANA.indb500BookAC18DANA.indb5 2022/03/1015:09:222022/03/1015:09:22

English

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the

power tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery for a purpose other than those

speciﬁed.

5. If the battery charging fails to complete even when a

speciﬁed recharging time has elapsed, immediately

stop further recharging.

6. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

7. Keep away from ﬁre immediately when leakage or

foul odor are detected.

8. Do not use in a location where strong static electricity

generates.

9. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

10. Do not disassemble battery charger; take it to a

qualiﬁed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁre.

11. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YFSL battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

REMEMBER: USE ONLY metabo HPT BATTERY TYPES

BSL18 SERIES. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING

Improper use of the battery or battery charger

can lead to serious injury. To avoid these

injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged

or is completely worn out. The battery can explode in

a ﬁre.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F

(0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use DC power to charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C) such as inside metal box or car.

12. NEVER expose the battery or battery charger to rain

or wet conditions.

13. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

00BookAC18DANA.indb600BookAC18DANA.indb6 2022/03/1015:09:222022/03/1015:09:22

English

10. Do not immerse the battery or allow any ﬂuids to ﬂow

inside. Conductive liquid ingress, such as water,

can cause damage resulting in ﬁre or explosion.

Store your battery in a cool, dry place, away from

combustible and ﬂammable items. Corrosive gas

atmospheres must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁnd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁrst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁre. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or

store by securely pressing into the battery

cover until the ventilation holes are concealed to

prevent short-circuits (See Fig. 3).

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁcation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations

of the destination country.

Power Output

2 to 3 digit number

Fig. 1

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

00BookAC18DANA.indb700BookAC18DANA.indb7 2022/03/1015:09:222022/03/1015:09:22

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁrst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀer from those on your own

power tool.

NAME OF PARTS

1. Cordless Caulking Gun

Hook

Release button

Protrusion

Piston

(for cartridges)

Rack handle

Battery

(sold separately)

Trigger switch

LED light

Name plate

Motor

Holder nut

Dial

Rack (push-out rod)

(300 ml holder)

300 ml holder

Fig. 2

2. Battery

(optional accessories…sold separately) 3. Battery Charger

(optional accessories…sold separately)

Ventilation holes

Latch

Terminals

Battery cover

Battery Nameplate

Pilot lamp

Guide rail

Cord

Ventilation holes

Fig. 3

Fig. 4

00BookAC18DANA.indb800BookAC18DANA.indb8 2022/03/1015:09:222022/03/1015:09:22

English

SPECIFICATIONS

1. Cordless Caulking Gun

Model AC18DA

Motor DC motor

Dispensing speed 0–33 inch/min (0–14 mm/s)

Maximum dispensing force 674 lbs (3,000 N)

Battery Type Li-ion battery Model BSL1830C (3.0 Ah)

Voltage DC 18 V

Weight 5.1 lbs. (2.3 kg) (BSL1830C attached)

2. Battery Charger

Model UC18YFSL

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C)) BSL1830C: Approx. 45 min

Charging voltage DC 14.4–18 V

Charging current DC 3.5 A

Weight 1.1 lbs. (0.5 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

00BookAC18DANA.indb900BookAC18DANA.indb9 2022/03/1015:09:232022/03/1015:09:23

English

ASSEMBLY AND OPERATION

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charge

indicator lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Firmly Insert the battery into the battery charger as

shown in Fig. 6.

Battery

Guide rail

Pilot lamp

Fig. 6

3. Charging

When inserting a battery in the charger, the pilot lamp

will light up continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1- second intervals.) (See

Table 2)

(1) Lamp indication

The indications of the pilot lamp will be as shown

in Table 2, according to the condition of the battery

charger or the battery.

APPLICATIONS

○

Applying in ducts, kitchens and bathrooms, exterior

walls, etc.

○

Filling joints of exterior walls or tile

○

Reinforcing airtightness and waterprooﬁng

○

Joining and attaching plate glass, and repairing

aquariums

INSTALLING AND REMOVING THE

BATTERY

○

How to install the battery.

Align the battery with the groove in tool handle and

slip it into place.

Always insert it all the way until it locks in place with a

little click, If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 5).

○

How to remove the battery.

Withdraw battery from the tool handle while pressing

the latch (2 pcs) of the battery (Fig. 5).

Latch

Handle

Battery

Pull out

Push

Insert

Fig. 5

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on

the nameplate, the charger will burn out.

00BookAC18DANA.indb1000BookAC18DANA.indb10 2022/03/1015:09:232022/03/1015:09:23

Inhaltsverzeichnis

Sprachen:

Andere Metabo HPT Werkzeuge Handbücher

Metabo HPT

Metabo HPT M 18DYA Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung